Bellini BR603GCX User manual

Installation and User manual

Content

Safety instructions----------------------------------------1

Product description---------------------------------------3

Operation mode-------------------------------------------4

Installation---------------------------------------------------5

Start using the range hood------------------------------10

Maintenance and cleaning------------------------------11

Warranty-----------------------------------------------------12

Curve Glass Canopy

Range Hood

20111101 Issue 4

BR603GCX

BR903GCX

For warranty service call 1300 373 199(Australia)

or 0508 123108(New Zealand) to connect you to

the nearest authorised service centre

Safety instructions

This manual explains the proper installation and use of your range hood, please read it

carefully before using even if you are familiar with the product. The manual should be kept

in a safe place for future reference.

Never to do:

zThis appliance is not intended for use by persons

(including children) with reduced physical, sensory

and mental capabilities, or lack of experience and

knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

zNever carry out flamable cooking under the

appliance

zThe exhaust from the range hood must not be

discharged into any heating flue, which may carry

combustion products from other sources.

zDo not leave lit gas burners exposed due to the risk

of fire.

zThis range hood is not recommended for

barbecues.

Always to do:

zPackaging materials (eg; polystyrene and

plastic items) must be kept out of reach of

babies or young children at all times due to

risk of suffocation.

zYoung children should be supervised to

ensure that they do not play with the

appliance.

zEnsure the range hood is switched off before

carrying out maintenance, to avoid any

possibility of electric shock.

zGrease filters must be removed every four

weeks (maximum) for cleaning to reduce the

risk of fire.

zThere must be adequate ventilation of the

room when the range hood is used at the

same time as appliances burning gas or other

fuels.

zAlways cover lit gas burners with pots or pans

when range hood is in use.

zAlways switch off gas burners before you

remove pots or pans.

zIf the supply cord is damaged, the cord must

be replaced by the manufacturer, its service

agent or similarly qualified persons in order to

avoid a hazard

zPlug must be accessible after installation.

Safety instructions

Never to do:

zThis range hood cannot be installed for outdoor use.

zIt is prohibited to fit the range hood over a solid fuel

stove

zThis appliance must not be connected to a chimney

or vent flue which is in use.

zThis appliance is not to be vented into the roof

cavity, must exit into open air.

zExhaust air must not be discharged into a wall

cavity, unless the cavity is designed for the purpose.

zThis appliance should not be connected to ducting

which ventilates rooms with fire places.

Always to do:

zAttention should be given to ensure that any

applicable regulations concerning discharge

of exhaust air are fulfilled.

zThis appliance should be installed and

maintained by a suitably qualified and

competent person in accordance with the

relevant safety regulations.

zBefore connecting the appliance to the mains

supply, ensure that the voltage and frequency

details on the rating plate are consistent with

the source of supply.

Product description

Component list:

1. Upper decorative chimney bracket

2. Upper decorative chimney(Inner)

3. Lower decorative chimney bracket

4. Flexible exhaust pipe

5. Lower decorative chimney(outer)

6. Hood mount bracket

7. Outlet(diameter 150mm)

8. Main body

9. Grease mesh filter

Technical data:

Power supply: 220 – 240v, 50Hz

Lights: 2x20W Halogen lamp

Motor: 190W

Length of power cord: 2m

Air outlet diameter: 150mm

Accessories bag

Description Picture QTY

User Manual 1

1:1 installation guide template 1

Upper decorative chimney bracket 1

Lower decorative chimney bracket 1

Hood mount bracket 1

Outlet( diameter 150mm)

Dry wall anchors plugs

Screw(ST4x8mm) 8

Screw(ST4x40mm)

Screw(ST4x30mm)

Screw(4x22mm)

Decorative ring* 4

Rubber insert* 4

*BR903GCS only

Operation Mode

Your range hood can be operated in two optional modes, choose the mode suitable for your kitchen before

installation. Air Exaction

Air Recirculation

To outside

To inside

For air exaction mode, a ducting kit is required, the air is

drawn in and cleaned by the grease filters and directed

outside.

Ducting must be vented to outside atmosphere.

For air recirculation mode, charcoal filter is a must to

eliminate cooking smells.

The air is drawn in and cleaned first by the grease filters

and then charcoal filter. The cleaned air is then

re-circulated back into kitchen through grilles on the

upper decorative chimney.

Installation

Dimensions:

BR603GCX BR903GCX

Installation:

Warning:

Check that the installation complies with the standards of local building, gas and electrical authorities. Before

connecting to the mains supply ensure the mains voltage corresponds to the voltage on the appliance rating

plate inside the range hood.

When installing the range hood, make sure you adhere to the minimum and maximum distances from the range

hood base to the cooktop hob surface.

Hints for exhaust duct installation

The following rules must be strictly followed to obtain optimal air extraction

•Keep exhaust duct short and straight

•Do not reduce the size or restrict exhaust duct

•When using flexible duct always install the duct pulled taut to minimize pressure loss

•Failure to observe these basic instructions will reduce the performance and increase noise levels of the

range hood

Ensure the exhaust ducting selected for installation complies with relevant standards and is fire retardant.

1. Using a spirit level mark a vertical centre line on the wall where the hood is to be positioned, and a horizontal

line where the hood base will be.

NOTE: The distance from the horizontal line to an electrical cooktop underneath must be minimum of

600mm & 650mm to a gas cook top and a maximum height of 800mm (refer to table below).

*If the instructions of the hob specify a greater distance than the minimum above, then that shall be the minimum height for installation

2. Use the installation guide template to determine where screw mount holes should be at. Make sure vertical

and horizontal line on the installation guide template superpose with the line just drew on the wall.

3. According to the position just marked by installation guide template, drill holes on the wall and hammer dry

wall anchor plugs into holes.

4. Fit the outlet on the top of range hood body with 4pcs ST4x8mm screws.

Hood baseHorizontal line

Vertical centre line

Top of hob

Minimum:

Electric 600mm

Gas 650mm

Maximum:

800mm

5. Fit the flexible exhaust pipe onto outlet.

* If choose air extraction mode, please install the flexible exhaust pipe; if choose air recirculation mode, no

need to install the flexible exhaust pipe, please skip this step and go to step 6 directly

6. Use 2pcs ST4x8mm screws to attach lower and upper chimney together, do not fasten screws too much,

make sure upper decorative chimney can be telescopically adjusted after assembled.

Lower decorative chimney(Outer)

7. Remove grease mesh filter and install active charcoal filter onto motor chamber according to below drawing.

* If choose air recirculation mode, we strongly recommend you have charcoal filter installed; if choose air

extraction mode, please skip this step and go to step 8 directly.

8. Secure the hood mount bracket onto wall with 3pcs screw ST4x40, make sure the screws are fastened

completely and the hood mount bracket is securely fastened to wall.

Upper decorative chimney(Inner)

Lower Chimney bracket

9. Hang on the hood onto the hook of the hood mount bracket, make sure the mount slot on cooker hood

completely slide into hooks.

*Above photo is for BR903GCX. For BR603GCX, glass already installed on main body

10. Fasten the 2pcs anti-tilt ST4x30mm screws onto wall to ensure horizontality of cooker hood. You can find out

screw holes inside hood near the motor chamber.

11. Use 3pcs ST4x40mm screws to secure the lower decorative chimney bracket onto wall.

12. Plug in the main power supply.

13. Determine position where upper decorative chimney maximum extent to, use 2pcs ST4x40mm screws to

secure the upper decorative chimney bracket onto wall.

*Total maximum extension height is 980mm; each chimney height is 500mm.

14. Carefully put the glass according to the arrow direction onto the cooker hood, and then fasten the screws+

decorative ring + rubber washer to fix the glass.

* for BR603GCX, glass already installed on main body so skip this step but go to next step directly.

15. Extend the upper decorative chimney to desired height and fix it with the upper decorative chimney bracket

by 2pcs ST4x8mm screws.

16. Remove all blue protective film on chimney and cooker hood, the installation is now finished.

This manual suits for next models

Table of contents

Other Bellini Ventilation Hood manuals

Bellini

Bellini BR903AX Installation instructions

Bellini

Bellini 0229596 Installation instructions

Bellini

Bellini BRA62SWP User manual

Bellini

Bellini BRA603SX User manual

Bellini

Bellini BBQRA123X Installation instructions

Bellini

Bellini BDR603TFG User manual

Bellini

Bellini BDRA603TBX2 Installation instructions

Bellini

Bellini BR603GCX-1 User manual

Bellini

Bellini BR903IPX User manual

Bellini

Bellini BRA903SLX Installation instructions

Bellini

Bellini BRA52UX Instruction Manual

Bellini

Bellini BRA603CPX Installation instructions

Bellini

Bellini BRA603SX-F Installation instructions

Bellini

Bellini CRHR6W01 User manual

Bellini

Bellini CRHR6W01 User manual

Bellini

Bellini BRA603GCX Installation instructions

Bellini

Bellini BRA603SX2 Installation instructions

Bellini

Bellini BDRA603TBX Installation instructions

Bellini

Bellini BRA52UX-F User manual

Bellini

Bellini BR603AX-F Installation instructions

Bellini

Bellini BR603SPX-F User manual

Bellini

Bellini BRA603GCX2 Installation instructions

Bellini

Bellini BBQR123X User manual

Bellini

Bellini BR603AX User manual

Popular Ventilation Hood manuals by other brands

emmeti

emmeti RECUPA MED A-140 Installation and use manual

Nibe

Nibe F135 user manual

Kuppersberg

Kuppersberg INTRO 60 Technical Passport

Zephyr

Zephyr Spruce AK9834BS Use, care and installation guide

Hisense

Hisense MH6INBG manual

Miele

Miele DA 1255 Operating and installation instructions

Broan

Broan 46000 Specification sheet

GE Profile PV977 Owner's Manual & Installation Instructions

FALMEC

FALMEC FFRIA24W5FS Instruction booklet

Whirlpool

Whirlpool RH2600XL-1 SERIES installation instructions

Küppersbusch

Küppersbusch DX ISLA instruction manual

ETNA

ETNA AV360RVS Instructions for use

JUNO

JUNO JDF603E6 installation manual

Miele

Miele DA 6708 D Operating and installation instructions

Tricity Bendix

Tricity Bendix LE 150 Installation & operating instructions

AEG

AEG X68163BV1 user manual

AEG

AEG 125 D operating instructions

Smeg

Smeg KSEV97X instruction manual