Bellini BR603AX User manual

啊哈

Installation and User manual

Content

Safety instructions---------------------------------- 1

Product description--------------------------------- 3

Operation mode-------------------------------------- 4

Installation--------------------------------------------- 5

Start using the range hood------------------------ 9

Maintenance and cleaning-------------------------10

Warranty------------------------------------------------ 11

20100610 issue 3

Black Fascia

Auto Slide-Out

Canopy Range Hood

BR603AX

BR903AX

BR603TBX

BR903TBX

Safety instructions 1

This manual explains the proper installation and use of your range hood, please read it

carefully before using even if you are familiar with the product. The manual should be kept

in a safe place for future reference.

Never to do:

zThis appliance is not intended for use by persons

(including children) with reduced physical, sensory

and mental capabilities, or lack of experience and

knowledge, unless they have been given

supervision or instruction concerning use of the

appliance by a person responsible for their safety.

zNever carry out flamable cooking under the

appliance

zThe exhaust from the range hood must not be

discharged into any heating flue, which may carry

combustion products from other sources.

zDo not leave lit gas burners exposed due to the risk

of fire.

zThis range hood is not recommended for

barbecues.

Always to do:

zPackaging materials (eg; polystyrene and

plastic items) must be kept out of reach of

babies or young children at all times due to

risk of suffocation.

zYoung children should be supervised to

ensure that they do not play with the

appliance.

zEnsure the range hood is switched off before

carrying out maintenance, to avoid any

possibility of electric shock.

zGrease filters must be removed every four

weeks (maximum) for cleaning to reduce the

risk of fire.

zThere must be adequate ventilation of the

room when the range hood is used at the

same time as appliances burning gas or other

fuels.

zAlways cover lit gas burners with pots or pans

when range hood is in use.

zAlways switch off gas burners before you

remove pots or pans.

zIf the supply cord is damaged, the cord must

be replaced by the manufacturer, its service

agent or similarly qualified persons in order to

avoid a hazard

zPlug must be accessible after installation.

Safety instructions 2

Never to do:

zThis range hood cannot be installed for outdoor use.

zIt is prohibited to fit the range hood over a solid fuel

stove

zThis appliance must not be connected to a chimney

or vent flue which is in use.

zThis appliance is not to be vented into the roof

cavity, must exit into open air.

zExhaust air must not be discharged into a wall

cavity, unless the cavity is designed for the purpose.

zThis appliance should not be connected to ducting

which ventilates rooms with fire places.

Always to do:

zAttention should be given to ensure that any

applicable regulations concerning discharge

of exhaust air are fulfilled.

zThis appliance should be installed and

maintained by a suitably qualified and

competent person in accordance with the

relevant safety regulations.

zBefore connecting the appliance to the mains

supply, ensure that the voltage and frequency

details on the rating plate are consistent with

the source of supply.

Product description 3

Component list:

1. Upper chimney retaining bracket

2. Upper decorative chimney (Inner)

3. Lower chimney retaining bracket

4. Flexible exhaust duct

5. Lower decorative chimney (outer)

6. Hood mount bracket

7. Outlet (diameter 150mm)

8. Main body

9. Grease mesh filter for BR603/903TBX

*2 pcs for BR603TBX, 3 pcs for BR903TBX

10. Grease mesh filter for BR603/903AX

Technical data:

Power supply: 220 – 240v, 50Hz

Motor: 190W

Lights: 2x20W Halogen lamp

Length of power cord: 2m

Air outlet diameter: 150mm

Accessories bag

Description Picture QTY

User Manual 1

1:1 installation guide template 1

Upper chimney retaining bracket 1

Lower chimney retaining bracket 1

Hood mount bracket 1

Outlet ( diameter 150mm)

Dry wall anchors plugs

Screw (ST4x8mm)

Screw (ST4x40mm)

Screw (ST4x30mm)

Operation Mode 4

Your range hood can be operated in two modes, choose the mode suitable for your kitchen before installation.

Air Extraction

Air Recirculation

To outside

To inside

For air extraction mode, a ducting kit is required, the air

is drawn in and cleaned by the grease filters and via the

ducting must be directed to the outside atmosphere.

Ducting must be vented to outside atmosphere

For air recirculation mode, charcoal filter (Optional

Accessory) must be installed to eliminate cooking

smells.

The air is drawn in and cleaned first by the grease filters

and then charcoal filter. The cleaned air is then

re-circulated back into kitchen through vents in the

Upper Decorative Chimney.

Installation 5

Dimensions:

BR603TBX/BR903TBX BR603AX/BR903AX

*Width of BR603TBX and BR603AX is 600mm, width of BR903TBX and BR903AX is 900mm

Installation:

Warning:

Check that the installation complies with the standards of local building, gas and electrical authorities. Before

connecting to the mains supply ensure the mains voltage corresponds to the voltage on the appliance rating

plate inside the range hood.

When installing the range hood, make sure you adhere to the minimum and maximum distances from the range

hood base to the cooktop hob surface.

Hints for exhaust duct installation

The following rules must be strictly followed to obtain optimal air extraction

•Keep exhaust duct short and straight

•Do not reduce the size or restrict exhaust duct

•When using flexible duct always install the duct pulled taut to minimize pressure loss

•Failure to observe these basic instructions will reduce the performance and increase noise levels of the

range hood

Ensure the exhaust ducting selected for installation complies with relevant standards and is fire

retardant.

1. Using a spirit level, mark a vertical line on the wall (Central to the cook top installed below) to indicate the

centre location of the hood and a horizontal line where the hood base will be positioned.

NOTE: The distance from the horizontal line to an electrical cooktop underneath must be minimum of

600mm & 650mm to the gas cook top and a maximum height of 800mm (refer to table below).

*If the instructions of the hob specify a greater distance than the minimum above, then that shall be the minimum height for installation

2. Use the installation guide template to determine where screw mount holes should be located. Make sure

vertical and horizontal lines on the installation guide template superimpose with the lines just drawn on the

wall.

3. According to the positions just marked as per installation guide template, drill holes in the wall and fit dry wall

anchor plugs into holes.

4. Fit the outlet on the top of range hood body and retain with 4pcs ST4x8mm screws.

Hood baseHorizontal line

Vertical centre line

Top of hob

Minimum:

Electric 600mm

Gas 650mm

Maximum:

800mm

5. Fit the flexible exhaust duct onto outlet. ( Air Extraction mode only )

Note : For the Air Circulation Mode option , skip step 5 and proceed with step 6.

6. Place Upper Decorative Chimney inside the Lower Decorative Chimney.

Connect the Lower Chimney retaining bracket to the Lower Decorative Chimney with 2 x ST4x8mm screws,

do not fully tighten, allowing for sufficient clearance to telescopically adjust the Upper Decorative Chimney to

the desired position when installation is completed.

Lower decorative chimney (Outer)

7. Install active Charcoal Filters ( Air Recirculation Mode only )

Note: For Air Extraction Mode option, skip Step 7 and proceed with Step 8.

Remove grease mesh filters and install active Charcoal Filter (Optional Accessory) onto the fan motor

housing (As shown in drawing below).

We strongly recommend the installation of Charcoal Filter to absorb cooking odors.

Upper decorative chimney (Inner)

Lower Chimney retaining bracket

8. Secure the hood mount bracket onto wall with 3 x ST4x40mm screws, making sure screws are securely

tightened.

9. Position the hood assembly onto the Hood Mount Bracket, ensuring that bracket hooks are securely

interlocking into the mounting slots of the hood assembly.

10. Secure the base of the hood with 2 x ST4x30mm anti -tilt screws to ensure unit is installed level , mounting

holes for the screws are accessible via the fan motor chamber.

11. Fasten the Lower Chimney retaining bracket to the wall with 2 x ST4x40mm screws.

12. Plug into the main power supply.

13. Position the Upper Chimney retaining bracket at the extendedheight of the decorative chimney and secure to

the wall with 2 x ST4x40mm screws.

* Total maximum extension height of BR603TBX and BR903TBX is 780mm, each chimney height is 400mm.

*Total maximum extension height of BR603AX and BR903AX is 980mm, each chimney height is 500mm.

14. Extend the Upper decorative chimney to the desired height and secure it with 2 x ST4 x 8mm screws to the

chimney retaining bracket.

15. Remove all blue protective film on chimney and cooker hood, the installation is now finished.

This manual suits for next models

Table of contents

Other Bellini Ventilation Hood manuals

Bellini

Bellini BRA603CPX Installation instructions

Bellini

Bellini BRA52UX-F User manual

Bellini

Bellini BRA603SX2 Installation instructions

Bellini

Bellini BRA903SLX Installation instructions

Bellini

Bellini CRHR6W01 User manual

Bellini

Bellini BBQRA123X Installation instructions

Bellini

Bellini BRA603SX-F Installation instructions

Bellini

Bellini BR603SPX-F User manual

Bellini

Bellini BR903IPX User manual

Bellini

Bellini BR603GCX User manual

Bellini

Bellini BDRA603TBX2 Installation instructions

Bellini

Bellini BDR603TFG User manual

Bellini

Bellini BRA603SX User manual

Bellini

Bellini BR603AX-F Installation instructions

Bellini

Bellini CRHR6W02 Installation instructions

Bellini

Bellini BR603GCX-1 User manual

Bellini

Bellini BRA52UX Instruction Manual

Bellini

Bellini 0229596 Installation instructions

Bellini

Bellini CRHR6W01 User manual

Bellini

Bellini BRA62SWP User manual

Bellini

Bellini BRA603GCX Installation instructions

Bellini

Bellini BRA603CPX2 Installation instructions

Bellini

Bellini BDRA603TBX Installation instructions

Bellini

Bellini BR903AX Installation instructions

Popular Ventilation Hood manuals by other brands

emmeti

emmeti RECUPA MED A-140 Installation and use manual

Nibe

Nibe F135 user manual

Kuppersberg

Kuppersberg INTRO 60 Technical Passport

Zephyr

Zephyr Spruce AK9834BS Use, care and installation guide

Hisense

Hisense MH6INBG manual

Miele

Miele DA 1255 Operating and installation instructions

Broan

Broan 46000 Specification sheet

GE Profile PV977 Owner's Manual & Installation Instructions

FALMEC

FALMEC FFRIA24W5FS Instruction booklet

Whirlpool

Whirlpool RH2600XL-1 SERIES installation instructions

Küppersbusch

Küppersbusch DX ISLA instruction manual

ETNA

ETNA AV360RVS Instructions for use

JUNO

JUNO JDF603E6 installation manual

Miele

Miele DA 6708 D Operating and installation instructions

Tricity Bendix

Tricity Bendix LE 150 Installation & operating instructions

AEG

AEG X68163BV1 user manual

AEG

AEG 125 D operating instructions

Smeg

Smeg KSEV97X instruction manual