AXIOMTEK NA-810A Manual
NA-810
Hardware Installation Guide
For service person only
ii
Disclaimers
The information in this manual has been carefully checked and is
believed to be accurate. AXIOMTEK Co., Ltd. assumes no
responsibility for any infringements of patents or other rights of third
parties, which may result from its use.
AXIOMTEK assumes no responsibility for any inaccuracies that may
be contained in this document. AXIOMTEK makes no commitment to
update or to keep current the information contained in this manual.
AXIOMTEK reserves the right to make improvements to this
document and/or product at any time and without notice.
No part of this document may be reproduced, stored in a retrieval
system, or transmitted, in any form or by any means, electronic,
mechanical, photocopying, recording, or otherwise, without the prior
written permission of AXIOMTEK Co., Ltd.
©Copyright 2007 by AXIOMTEK Co., Ltd.
All rights reserved.
Version A1 January 2007
Printed in Taiwan
iii
Safety Approvals
CE Marking
FCC Class A
FCC Compliance
This equipment has been tested and complies with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. If not installed and used in
accordance with proper instructions, this equipment might generate
or radiate radio frequency energy and cause harmful interference to
radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one
or more of the following measurers:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with
emission limits.
iv
Safety Precautions
Before getting started, read the following important cautions.
1. Be sure to ground yourself to prevent static charge when
installing the internal components. Use a grounding wrist strap
and place all electronic components in any static-shielded
devices. Most electronic components are sensitive to static
electrical charge.
2. Disconnect the power cords from the NA-810 before making
any installation. Be sure both the system and the external
devices are turned OFF. Sudden surge of power could ruin
sensitive components. Make sure the NA-810 is properly
grounded.
3. Do not open the system’s top cover. If opening the cover for
maintenance is a must, only a trained technician is allowed to
do so. Integrated circuits on computer boards are sensitive to
static electricity. To avoid damaging chips from electrostatic
discharge, observe the following precautions:
9Before handling a board or integrated circuit, touch an
unpainted portion of the system unit chassis for a few seconds.
This will help to discharge any static electricity on your body.
9When handling boards and components, wear a wrist-grounding
strap, available from most electronic component stores.
Trademarks Acknowledgments
AXIOMTEK is a trademark of AXIOMTEK Co., Ltd.
Other brand names and trademarks are the properties of their
respective owners.
v
Table of ContentsDisclaimers ......................................................ii
FCC Compliance.........................................................................iii
Chapter 1..............................................................................................1
1.1 General Description............................................................1
1.2 Standard Features..............................................................2
1.3 System Specifications.........................................................2
1.3.1 Hardware.................................................................2
1.4 System Placement..............................................................5
Chapter 2..............................................................................................2
2.1 Preinstallation Checklist .....................................................2
2.2 Connectors and Jumpers....................................................2
2.2.1 Connectors ..............................................................2
2.2.2 Jumper Settings .........................................................3
2.3 Setting up the appliance.....................................................5
2.3.1 Installing a memory module (DIMM)..........................5
2.3.2 Installing Display Interface.......................................5
2.3.3 Installing Serial Port Interface..................................5
2.3.4 Installing Keyboard and PS/2 Mouse DIN
Connectors..........................................................................6
Chapter 3..............................................................................................7
3.1 BIOS Introduction...............................................................7
3.2 BIOS Setup.........................................................................7
3.3 Standard CMOS Setup.......................................................8
3.4 Advanced BIOS Features.................................................11
3.5 Advanced Chipset Features.............................................16
3.6 Integrated Peripherals......................................................18
3.7 Power Management Setup...............................................22
3.8 PNP/PCI Configuration.....................................................26
vi
3.9 PC Health Status..............................................................29
3.10 Frequency / Voltage Control.............................................30
3.11 Load Optimized Defaults..................................................31
3.12 Set Supervisor/User Password.........................................32
3.13 Save & Exit Setup.............................................................34
3.14 Quit Without Saving..........................................................35
Appendix A......................................................................................... 36
NA-810 Hardware Installation Guide
Introduction
Chapter 1
Introduction
This chapter contains the general information and the detailed
specifications of the NA-810 Network Appliance server. Chapter 1
includes the following sections:
1.1 General Description
NA-810A
NA-810B
NA-810C
1
NA-810 Hardware Installation Guide
Introduction
2
NA-810 series is designed for network software solution providers
those have data secure, voice over IP, video streaming, network
bandwidth controller and another networking appliance requirements
across this stable and reliable multiple LAN device.
There can be deployed up to four Ethernet LAN ports combinations
for customer selection in the maximum for application.
NA-810 series has pretty good enclosure management interface to be
implemented in the factory default. It can support P.O.S.T (Power on
Self Test) feature through hyper-terminal by console port.
And it has room space for one hard drive deployment. Customer can
implement system log and monitoring functions through this
hardware specification. With its innovative mechanical and
electrical design, NA-810 series provides one mini-PCI expansion slot
for VPN encryption / decryption adapter board and another special
functions enabling. It cans enhancement network security process
performance and of-load the CPU loading.
NA-810 series can support wonderful networking application platform
by excellent cost with performance ratio.
1.2 Standard Features
zVIA V4 Eden / C7 processor with 400MHz FSB
zFour Ethernet LAN ports combinations are for NA-810.
zSupport BIOS redirected to COM port feature
zSupport RS-232 and two USB
zOne Mini-PCI slot for another network security encryption
board
zSupports Linux Code 2.6 afterward version.
1.3 System Specifications
1.3.1 Hardware
zProcessor:
VIA V4 Eden / C7 processor with 400MHz FSB
NA-810 Series:
NA-810 Hardware Installation Guide
Introduction 3
NA-810A-4ER-400ÆEden 400MHz
NA-810B-4ER-1GÆC7 1GHz
NA-810C-4ER-1.5GÆC7 1.5GHz
zBIOS:
Award 4MB Flash BIOS Plug & Play
zL2 Cache:
Built-in in CPU
zMain Memory:
One DDRII 400/533 memory SO-DIMM can be up to 1GB in the
maximum
zIDE Interface:
Support two ATA 66/100/133 EIDE channels
Support two channels for S-ATA 1
zEthernet:
Totally has four 10/100 Ethernet LAN port connections are
available.
zExpansion:
One Mini-PCI 32-bit/33MHz for security encryption card or other
third-party cards expansion
zCompact-FlashTM:
One IDE interface CompactFlashTM socket for embedded use
zLink/Active LED (Single color)for LAN port #1, port#2, port#3 and
port#4
1. The yellow LED is on when there is an active connection on the
LAN port.
2. The LED flashes when there is transmit or receive activity to or
from the appliance.
3. The LED is dark when it off line.
zDimensions:
NA-810A: 30mm(H) x 214mm(W) x 150mm(D)
NA-810B: 44mm(H) x 214mm(W) x 150mm(D)
NA-810C: 44mm(H) x 430mm(W) x 248mm(D)
NA-810 Hardware Installation Guide
Introduction
4
zOperation environment:
Air temperature: 0° C – 40°C
Humidity: 5% – 95%
This manual suits for next models
2
Table of contents
Other AXIOMTEK Server manuals
AXIOMTEK
AXIOMTEK NA-814 Manual
AXIOMTEK
AXIOMTEK NA-821 Series User manual
AXIOMTEK
AXIOMTEK IRU131 User manual
AXIOMTEK
AXIOMTEK NA-550 Series User manual
AXIOMTEK
AXIOMTEK NA-1301 Manual
AXIOMTEK
AXIOMTEK NA-401 Manual
AXIOMTEK
AXIOMTEK NA590 Series User manual
AXIOMTEK
AXIOMTEK NA580 series User manual
AXIOMTEK
AXIOMTEK NA-320 Series User manual
AXIOMTEK
AXIOMTEK NA570 Series User manual
