AUROOM Cala User manual
Prefabricated sauna cabin
Dry finnish sauna cabin
INSTALLATION MANUAL
MODEL Cala 150x150
auroomwellness.com
Assembly instructions
1. Preparations
·Sauna package must be stored in a heated and dry room.
·Prior to installation ithe package must be opened and stored for 48h to adjust to
relative humidity of the room (22o
C, 40-60% RH).
·Ensure the sauna model fits in the designated room with sufficient extra room for
ease of installation.
·Clean the location of sauna with care in order to not damage any details, elements
·Room must be well ventilated and with water drain on or near the position of the
sauna.
·Sauna is intended to be installed on a level surface to ensure proper installation and
quality of the installed product.
·Adequate electrical supply must be ensured for electrical components of the sauna.
Refer to user manuals of respective products.
·Electrical connections to the power grid and to the sauna may only be carried out by
legally competent and certified specialist.
·Producer cannot be held responsible for any errors resulting from disregard to the
levelness of substructure, inadequate storing conditions, inadequate power supply,
unauthorized alterations to components or any other circumstances occuring from
deviations described in this manual and/or good customs.
2. List of tools
·Water level
·Tape measure
·Power drill
·Rubber or plastic mallet
·Silicone gun
·Screwdriver set
Installation of a sauna requires at least two (2) persons.
3. Installations
·Follow the instructions precisely.
·Always start from 1 and continuosly move forward in an organized manner.
·Keep the installation site always clean and organized.
·This manual does not take into account any possible peculiarities of the installation
site.
·Take care not to damage any components during installation due to dropping,
dragging or careless handling.
·Special attention towards elements - they must be stored with care and kept away
from any hard or sharp objects. Glasses are tempered and even smallest damages
to the surface or corners can lead to concentration of stress and shattering of the
glass.
1. Baseframe
1. Check substructure level. Sauna must be installed on a level surface.
2. Connect the base frame elements
3. Fix the elements with screws
4. Check baseframe diagonals for equality and right corners
5. Apply silicone under basefame and fix in place
NOTE! If the sauna is to be moved after installation, silicone can be installed afterwards.
Figure 1a.
Figure 1b.
Diagonal 1
Diagonal 2
2. Wall elements
1. Start assembly by placing previously assembled elements
A1 & A2 on stable baseframe.
2. Fix A1 & A2 elements with corner post CP-1 as indicated on Figure 2a, 2b.
Figure 2a.
A1
1
A2
2CP-1
3
Corner fixing
Figure 2b.
Corner fixing
Figure 2b.
2.1 Wall elements
1. Place previously assembled elements B1 & B2 on stable baseframe.
2. Fix B1 & B2 elements with corner post CP-1 as indicated on Figure 2.1a, 2.1b.
Figure 2.1a.
B1
1
B2
2
CP-1
3
Corner fixing
Figure 2.1b.
Corner fixing
Figure 2.1b.
2.2 Wall elements
1. Place previously assembled elements C1 & C2 on stable baseframe.
2. Fix C1 & C2 elements with corner post CP-1 as indicated on Figure 2.2a, 2.2b.
Figure 2.2a.
Corner fixing
Figure 2.2b.
Corner fixing
Figure 2.2b.
C1
1
C2
2
CP-1
3
2.3 Wall elements
1. Place previously assembled element D1 on stable baseframe.
2. Fix D1 element with corner post CP-1 as indicated on Figure 2.3a.
Figure 2.3a.
D1
1
3. Ceiling elements
1. Place the first ceiling element on top of prefiously installed and fixed wall elements (Figure
3a). Check walls for vertical level. Ceiling element must sit flush with walls external layer
and with no excessive gaps between internal panels. Fix with screws.
2. Place the second ceiling element on top of walls with approx. 10mm gap with previous
ceiling and slide into place. Attach additional plywood support pieces on the joint between
ceilings. Fix with screws around.
NOTE! Do not support elements on edge of previous installed element!
Figure 3a.
CE1
CE2
4. Bench support placement
Figure 4a.
1. Place bench supports in sauna, check for level.
2. Fix bench supports with screws.
639
239
Figure 4b.
600
Figure 5a.
5. Bench frames
1. Place upper bench frame and fix with screws.
2. Place lower bench frame and fix with screws.
NOTE! First fasten the screws on sidewalls, then backwall.
2
1
Figure 5b.
Table of contents
Other AUROOM Plumbing Product manuals
Popular Plumbing Product manuals by other brands
Weka
Weka 506.2020.00E ASSEMBLY, USER AND MAINTENANCE INSTRUCTIONS
Kohler
Kohler K-6228 Installation and care guide
UBERHAUS DESIGN
UBERHAUS DESIGN 75175017 Operator's manual
American Standard
American Standard DetectLink 6072121 manual
Uponor
Uponor Contec TS Mounting instructions
Pfister
Pfister Selia 49-SL Quick installation guide
Kohler
Kohler Centerset K-15240 Homeowner's guide
Viega
Viega Prevista Dry 8522.33 Instructions for use
Sanela
Sanela Lema SLP 59RB Instructions for use
Elkay
Elkay EDF15AC Installation, care & use manual
Hans Grohe
Hans Grohe AXOR Citterio E 36702000 Instructions for use/assembly instructions
baliv
baliv WT-140 manual