Atmel ATSAMB11 BluSDK SMART User manual

ATSAMB11 BluSDK SMART

AT Command - Getting Started Guide

USER GUIDE

Introduction

This document explains the details about:

Getting started with the setup of ATSAMB11 Xplained board

How to use AT Command on ATSAMB11 Xplained board

Features

Reset the link layer

Set device configuration

Start scan

Stop scan

Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]

Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016

Table of Contents

Introduction .....................................................................................................................1

Features .....................................................................................................................1

Table of Contents ........................................................................................................2

1Purpose .....................................................................................................................3

2Demo Setup..................................................................................................................4

3Hardware Setup ...........................................................................................................5

4Software Setup.............................................................................................................6

4.1 Installation Steps...................................................................................................................................6

4.2 Build Procedure.....................................................................................................................................6

5Running the Demo.......................................................................................................8

6BluSDK SMART Software Architecture....................................................................10

7ATMEL EVALUATION BOARD/KIT IMPORTANT NOTICE AND DISCLAIMER........11

8Revision History ........................................................................................................12

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]

Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016

1 Purpose

This getting started guide describes the setup of ATSAMB11 Xplained board and bringing up an AT CMD

example supplied as part of BluSDK Smart release.

The AT command set is listed in the following table.

Table 1-1. AT Command Set

Command

Command Description

Command Syntax

Reset

Reset the link layer

AT+RESET

Configuration

Set device configuration

AT+CFG_DEF

Start Scan

Start scan operation

AT+SCAN

Stop Scan

Stop an ongoing scan operation

AT+STOP

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]

Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016

2 Demo Setup

Figure 2-1. Demo Setup of the AT CMD Application on ATSAMB11

USB Cable

AT Command Prompt

ATSAMB11

BLE Link

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]

Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016

3 Hardware Setup

Connect the ATSAMB11 board to the host PC using a Micro-USB cable.

Figure 3-1. EDBG USB Port

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]

Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016

4 Software Setup

4.1 Installation Steps

1. Install the latest Atmel Studio [Atmel Studio 7.0 (build 629 or later) web installer

(recommended)]

http://www.atmel.com/tools/ATMELSTUDIO.aspx.

2. Install the latest Atmel Software Framework.

This package will install the following examples within the Atmel Studio environment:

AT CMD application for ATSAMB11

4.2 Build Procedure

The following procedure is explained for ATSAMB11 application example.

1. Select New Example Project.

Figure 4-1. Creating a New Example Project

2. Select “SAMB11” in device family, enter “at cmd” in search window, and expand Atmel Corp

Projects. The location and the name of the project can be selected in the respective fields. Click

OK.

Figure 4-2. Selecting AT CMD Application from Example Projects

3. Accept the license Agreement. The Atmel studio will generate the AT CMD project for ATSAMB11.

4. Build the solution.

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]

Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016

Figure 4-3. Building the AT CMD Application

5. Download the application via the USB to the ATSAMB11 board by using the Device Programing

option available in Tools as shown below.

Figure 4-4. Flashing the Application on Atmel MCU

6. Inside the device programming the user has to select the correct configuration for the device and

finally program the device by using the program button.

Figure 4-5. Flash Programming

7. Once the application is flashed, now AT CMD Application is ready for usage.

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]

Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016

5 Running the Demo

Type one of four commands you want on the console.

1. Reset command

Type “AT+RESET” and then press ‘Enter’ key.

Figure 5-1. RESET command

UART Initialized

Device name : Atmel BLE Device

Device Address : 0xF8F005F35D67, Type : 0

>>BLE Stack Initialized, use “AT+” for AT-Commands

# CMD Handler Ptr.

-------------------------------------------------------

01 RESET 100108b9

02 SCAN 10010917

03 STOP 10010941

04 CFG_DEF 100108cf

-------------------------------------------------------

AT+RESET

Searching for CMD handler...

Processing...Reset Handler

DONE

2. CFG_DEF command

Type “AT+CFG_DEF” and then press ‘Enter’ key.

Figure 5-2. CFG_DEF command

AT+CFG_DEF

Searching for CMD handler...

Processing... Config Handler

DONE

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]

Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016

3. SCAN command

Type “AT+SCAN” and then press ‘Enter’ key. After a while, scan results should be shown as below.

Figure 5-3. SCAN command

AT+SCAN

Searching for CMD handler...

Processing... Scan Handler

DONE

AT_BLE_SCAN_INFO:

Device Addr.: 0xF8F005F35BE4

AddrType : 0x00

RSSI : -68

AT_BLE_SCAN_INFO:

Device Addr.: 0xF8F005F35BE4

AddrType : 0x00

RSSI : -66

AT_BLE_SCAN_INFO:

Device Addr.: 0xACEE9E19AE82

AddrType : 0x00

RSSI : -78

AT_BLE_SCAN_INFO:

Device Addr.: 0xF8F005F35978

AddrType : 0x00

RSSI : -77

AT_BLE_SCAN_INFO:

Device Addr.: 0xF8F005F35978

AddrType : 0x00

RSSI : -76

4. STOP command

Type “AT+STOP” and then press ‘Enter’ key.

Figure 5-4. STOP command

AT+STOP

Searching for CMD handler...

Processing... Stop Handler

DONE

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]

Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016

6 BluSDK SMART Software Architecture

Figure 6-1 illustrates the top level diagram for the BLU-SDK SMART configuration.

Figure 6-1. ATSAMB11 Software Architecture

Other manuals for ATSAMB11 BluSDK SMART

Table of contents

Other Atmel Microcontroller manuals

Atmel

Atmel develer DevelBoard Blue Quick user guide

Atmel

Atmel SAM4L Xplained Pro User manual

Atmel

Atmel AT89C5131A-L User manual

Atmel

Atmel AVR32918 User manual

Atmel

Atmel XMEGA A3 series User manual

Atmel

Atmel AT88CK101BK8 Installation manual

Atmel

Atmel AT18F-DK3 User manual

Atmel

Atmel STK520 User manual

Atmel

Atmel ATtiny13A User manual

Atmel

Atmel SAM4SD32B Instruction Manual

Atmel

Atmel C51 Installation and operating instructions

Atmel

Atmel ATAB5749 Installation and operating instructions

Atmel

Atmel AVR ATtiny15L Owner's manual

Atmel

Atmel ATtiny104 Xplained Nano User manual

Atmel

Atmel AVR4901 Installation and operating instructions

Atmel

Atmel AVR2052 User manual

Atmel

Atmel SMARTCARD XPRO User manual

Atmel

Atmel AVR ATtiny15L User manual

Atmel

Atmel AT32UC3L064 User manual

Atmel

Atmel SAM G55 Xplained Pro User manual

Atmel

Atmel MC320 User manual

Atmel

Atmel AT32UC3A3256S User manual

Atmel

Atmel ATtiny25 User manual

Atmel

Atmel AVR ATmega103 User manual

Popular Microcontroller manuals by other brands

AMS

AMS AS7261 Demo Kit user guide

Novatek

Novatek NT6861 manual

Espressif Systems

Espressif Systems ESP8266 SDK AT Instruction Set

Nuvoton

Nuvoton ISD61S00 ChipCorder Design guide

STMicrolectronics

STMicrolectronics ST7 Assembler Linker user manual

Texas Instruments

Texas Instruments Chipcon CC2420DK user manual

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM user guide

NEC

NEC 78GK0S/K 1+ Series Application note

Mikroe

Mikroe SEMITECH N-PLC Click Application note

Intel

Intel Agilex user guide

Cypress

Cypress CY4607 HX2VL quick start guide

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE manual

Texas Instruments

Texas Instruments TMS320F2837 D Series Workshop Guide and Lab Manual

CYPRES

CYPRES CY14NVSRAMKIT-001 user guide

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM user guide

Espressif Systems

Espressif Systems ESP8266EX Programming guide

Abov

Abov AC33M8128L user manual

Laird

Laird BL654PA user guide