Aluprof DC282 User manual
1
433MHz
OPERATING MANUAL FOR UNDER PLASTER SWITCH WITH RADIO RECEIVER
DC282, DC228, DC318, DC319
AC
230V/50Hz
Technical specifications:
Technical data:
- Power supply: ~ 230 V / 50 Hz
- Applied for max 50 Nm tubular motor
- Frequency: 433.92MHz
- Can store 20 channels at most
- Radiated power: 10 miliwat (mW)
- Operating temperature: ~ -20oC ~ +55oC
- Average range: 200 meters (in open space)
35 meters (inside building)
- Dimension 80x80 mm
Works with standard version tubular motors and can match all DC
remote controllers (without DC115B).
Company reserves the tolerance of catalog data due the different
conditions usage.
DC282
DC228
DC318
DC319
NOTE
- Installation of the switch should be carried out by authorized persons
(e.g. SEP authorisations to operate electrical devices up to 10 kV).
- The switch is designed for use in dry rooms and should not be exposed
to direct weather conditions..
- The switch should be powered by a separate circuit and protected by a quick
fuse for example: circuit breaker type B10
Buttons function
SET P2
LED
DOWN
STOP
UP
LED
UP
STOP
DOWN
Activation of the P2 SET button
in remote controller DC318
and DC 319 is performed by a
combination of both keys
“UP” and “DOWN”.
Central Office, Production Plant in: Bielsko –Biala
ul. Warszawska 153, 43-300 Bielsko Biała, Polska
tel. +48 33 81 95 300, fax. +48 33 82 28 512
Production Plant:
ul. Gosławicka 3, 45-446 Opole, Polska
tel. +48 77 40 00 000, fax. +48 77 40 00 006
e-mail: Aluprof@aluprof.eu
2
1. Electrical connections between motor and under plaster swich
Power 230V / 50 Hz
DC282
2. Memorizing the first transmitter
The sequences should be done for the first and each additional transmitter which has to be programmed
Power on, next press „SET P2”
button
The LED should
blink
Press „STOP” button
The LED is
lightining
Pres the „UP”
buton on the
remote controller
The LED will blink
3 times
OK
The transmitter
has been added
correctly
3. Erasing the memory
The sequences should be done for each transmitter which had to be deleted
Power on, next press „SET P2”
button
The LED should
blink
Press „STOP” button
The LED is
lightining
Pres the „DOWN”
buton on the
remote controller
The LED will blink
3 times
OK
The transmitter
has been deleted
correctly
Wiring diagram
4. Mode change (with or without suport)
Power on, next press „UP” & „STOP”
buton at once for 6 seconds
The LED wil blink 3 times.
Reset done correct.
OK
the operating
mode has been
changed
"In accordance with the provisions of the Directive of the European Parliament and of the Council 2012/19 / EU of 4 July 2012 on waste
electrical and electronic equipment (WEEE), it is prohibited to place of used equipment together with other wastes, marked with crossed
out wheeled bin symbol.
The users are obliged to transfer their used equipment to a designated collection point for proper processing.
The marking means, at the same time, that the equipment was put on the market after 13 August 2005.
These legal obligations have been introduced to reduce the amount of waste generated from waste electrical and electronic equipment
and to ensure an appropriate level of collection, recovery and recycling. The equipment does not contain any dangerous components,
which would have any particularly negative impact on the environment and human health."
This manual suits for next models
3
Other Aluprof Receiver manuals
