ACME Solaris User manual

CONTENTS

1. Safety Instructions ......................................................................................... 2

2. Technical Specifications ................................................................................. 4

3. Control Panel ................................................................................................. 6

4. How To Set The Unit....................................................................................... 6

4.1 Main Function.......................................................................................... 6

4.2 Home Position Adjustment .................................................................... 14

5. Control By Universal DMX Controller ........................................................... 14

5.1 DMX512 Connection.............................................................................. 14

5.2 Address Setting ...................................................................................... 15

5.3 DMX512 Configuration........................................................................... 16

6. Troubleshooting........................................................................................... 31

7. Fixture Cleaning ........................................................................................... 32

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will

not accept liability for any resulting defects or problems.

Unpack and check carefully that there is no transportation damage before using the unit.

This product is for indoor use only. Use only in a dry location.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.

DO NOT connect the device to any dimmer pack.

Make sure there are no flammable materials close to the unit while operating to avoid fire

hazard.

Examine the power wires carefully; replace them immediately if there is any damage.

Unit’s surface temperature may reach up to 55℃. DO NOT touch the housing bare-handed

during its operation.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut

off the mains power immediately.

DO NOT operate in dirty or dusty environment, do clean fixtures regularly.

Please read the instruction carefully which includes important information about

the installation, usage and maintenance.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together twist other cables.

The minimum distance between light output and the illuminated surface must be more than

0.2 meters.

Disconnect mains power before fuse replacement or servicing.

Replace fuse only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center if

needed.

Disconnect the mains power if the fixture is has not been used for a long time.

DO use the original packing materials before transporting it again.

DO NOT look directly at the light while the LED is on.

DO NOT start on the unit without LED enclosure or when housing is damaged.

Installation:

The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of the

fixtures weight. Always use a safety cable that can hold 12 times of the weight of the fixture when

installing.

The equipment must be installed by professionals. It must be installed in a place where is out of the

reach of people and no one can pass by or under it.

2. Technical Specifications

Power Voltage:

AC 100~240V, 50/60Hz

Power Consumption:

580W

Light Source:

36x15W RGBW LED

49x0.06W CW LED

Beam Angle:

6°

Spot Angle:

10.8°

Movement:

Pan/Tilt movement: 360° Infinite

Pan/Tilt Resolution: 16bit

Dimmer/Shutter:

Smooth dimming from 0~100%, with 4 optional dimming curves; outstanding strobe effect with

variable speed

Control:

DMX channel: 166/206/22+144/21 channels

Protocols: DMX512, RDM, Art-Net

Firmware Upgrade via DMX link

Construction:

Display: LCD display

Data In/Out: 3-pin&5-pin XLR, RJ-45

Power In/Out: Power Connector in/out

Protection Rating: IP20

Features:

Variable CTO

Integrated multi features: beam, wash, pixel effect, star background and moonflower beam

36 (6x6) x 15W RGBW pixel control LED + 49 (7x7) CW star-effect LED

Preset a variety of graphics matrix effect

Outstanding color mixing effect

Excellent thermal control

Low noise: fan speed can be adjusted automatically according to temperature

Optional reflector mirror module can create moonflower effect

Dimensions/ Weight:

466x246x575mm, 20kgs

18.3”x9.7”x22.6”in, 44.1lbs

466mm

575mm

246mm

3. Control Panel

1. LED:

POWER

Power on

DMX

DMX input present

2. Display: To show the various menus and the selected function

3. Button:

To enter into move backward or leave the menu

To go backward to move up in the menu

DOWN

To go forward to move down in the menu

ENTER

To perform the desired functions

4. DMX IN:

For DMX512 link, use 3/5-pin XLR cable to link the unit and DMX controller

5. DMX OUT:

For DMX512 link, use 3/5-pin XLR cable to link the next units

6. ETHERNET: Transfers fixture’s information to a main controller

7. POWER IN: Connects to supply power

8. POWER OUT: Connects to the next fixture

9. FUSE(T 15A): Protects the unit from damage of over current

4. How To Set The Unit

4.1 Main Function

Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until

the required function is shown on the monitor. Select the function by the ENTER button. Use the

UP/DOWN button to choose the submenu, press the ENTER button to store and automatically

return to the last menu. Press the MENU button or let the unit idle 30 seconds to exit menu mode.

The main functions are shown below:

DMX Setting

To select DMX Settings,press the ENTER button to confirm, use the UP/DOWN button to select

Channel Mode, Art-Net Setup, Port A DMX Address or Port B DMX Address.

Channel Mode

To select Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to select

166 CH,206 CH, 22+144CH or 21 CH, press the ENTER button to store. Press the MENU button back

to the last menu or let the unit idle 30 seconds to exit menu mode.

Are-Net Setup

To select Are-Net Setup, press the ENTER button to confirm. Use the UP/DOWN button to select

Ethernet IP Setup or Art-Net Port Setup, press the ENTER button to store. When choose the

Ethernet IP Setup, use the UP/DOWN button to select IP Address or Subnet Mask.When choose

the Art-Net Port Setup, use the UP/DOWN button to select Net, Subnet, Port A Universe or Port B

Universe. Press the MENU button back to the last menu or let the unit idle 30 seconds to exit menu

mode.

Port A DMX Address

To select Port A DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to

adjust the address from 001 to 512, press the ENTER button to store. Press the MENU button back

to the last menu or let the unit idle 30 seconds to exit menu mode.

Port B DMX Address (This menu will only appear when the “Channel Mode” has selected the

“22+144 CH”)

To select Port B DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to

adjust the address from 001 to 512, press the ENTER button to store. Press the MENU button back

to the last menu or let the unit idle 30 seconds to exit menu mode.

Fixture Setting

To select Fixture Setting, press the ENTER button to confirm, use the UP/DOWN button to select

DMX Last State, Dimmer Speed, Pan Invert, Tilt Invertor P/T Feedback.

DMX Last State

To select DMX Last State, press the ENTER button to confirm. Use the UP/DOWN button to select

Hold (fixture continues to obey the last command it received Via DMX if DMX signal stops) or

Blackout (fixture blacks out if DMX signal stops), press the ENTER button to store. Press the MENU

button back to the last menu or let the unit idle 30 seconds to exit menu mode.

Dimmer Speed

To select Dimmer Speed, press the ENTER button to confirm. Use the UP/DOWN button to select

Fast or Smooth, press the ENTER button to store. Press the MENU button back to the last menu or

let the unit idle 30 seconds to exit menu mode.

Pan Invert

To select Pan Invert, press the ENTER button to confirm. Use the UP/DOWN button to select No

(normal) or Yes (pan invert), press the ENTER button to store. Press the MENU button back to the

last menu or let the unit idle 30 seconds to exit menu mode.

Tilt Invert

To select Tilt Invert, press the ENTER button to confirm. Use the UP/DOWN button to select No

(normal) or Yes (tilt invert), press the ENTER button to store. Press the MENU button back to the

last menu or let the unit idle 30 seconds to exit menu mode.

P/T Feedback

To select P/T Feedback, press the ENTER button to confirm. Use the UP/DOWN button to select No

(Pan or tilt’s position will not feedback while out of step) or Yes (Feedback while pan/tilt out of step),

press the ENTER button to store. Press the MENU button back to the last menu or let the unit idle

30 seconds to exit menu mode.

Display Setting

To select Display Setting, press the ENTER button to confirm, use the UP/DOWN button to select

LCD Intensity, LCD Contrast Ratio, Display Invert or Language.

LCD Intensity

Select LCD Intensity, press the ENTER button to confirm, present mode will blink on the display, use

the UP/DOWN button to adjust the value from 1 (dark) to 10 (bright), press the ENTER button to

store. Press the MENU button back to the last menu or let the unit idle 30 seconds to exit menu

mode.

LCD Contrast Ratio

Select LCD Contrast Ratio, press the ENTER button to confirm, present mode will blink on the

display, use the UP/DOWN button to adjust the value from 1to 30, press the ENTER button to store.

Press the MENU button back to the last menu or let the unit idle 30 seconds to exit menu mode.

Table of contents

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions