ACME ICARUS 620 User manual

CONTENTS

1. Safety Instructions ......................................................................................... 2

2. Technical Specifications ................................................................................. 4

3. How To Set The Unit....................................................................................... 5

3.1 Control Panel ........................................................................................... 5

3.2 Main Function.......................................................................................... 6

3.3 Home Position Adjustment .................................................................... 14

4. Control By Universal DMX Controller ........................................................... 14

4.1 DMX512 Connection.............................................................................. 14

4.2 Address Setting ...................................................................................... 15

4.3 DMX512 Configuration........................................................................... 16

5. Troubleshooting........................................................................................... 23

6. Fixture Cleaning ........................................................................................... 24

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will

not accept liability for any resulting defects or problems.

Unpack and check carefully to ensure that there is no transportation damage before using the

unit.

This product is for indoor use only. Use only in a dry location.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots is blocked, otherwise the unit will be overheated.

Before operation, ensure that you are connecting this product to the proper voltage in

accordance with the specifications in this manual or on the product’s specification label.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.Do not

operate this product at a lower or higher temperature.

DO NOT connect the device to any dimmer pack.

Keep flammable materials away from the fixture while operating to avoid fire hazard.

Make sure the power cord is not crimped or damaged; replace it immediately if damaged.

Unit’s surface temperature may reach up to 75℃. DO NOT touch the housing bare-handed

during its operation.

Avoid any flammable liquids, water or metal from entering the unit. Once it happens, cut off

the mains power immediately.

Please read the instruction carefully which includes important information

about the installation, usage and maintenance.

DO NOT operate in a dirty or dusty environment. DO clean the fixture regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid entanglement of the power cord with other wires.

The minimum distance to objects/surface must be more than 1.5 meters.

Disconnect mains power before fuse replacement or servicing.

Replace fuse only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the housing as there are no user serviceable parts inside.

DO NOT attempt to operate this unit if it becomes damaged. DO NOT attempt any repairs

yourself. Repairs carried out by unskilled people can lead to damage or malfunction. Please

contact the nearest authorized technical assistance center if needed.

Disconnect this product from its power source before servicing.

DO use the original packaging if the device is to be transported.

Avoid direct eye exposure to the light source while the product is on.

DO NOT operate this product if you see damage on the housing, shields, or cables. Have the

damaged parts replaced by an authorized technician at once.

Installation:

The fixture should be fixed on the clamp. Always ensure that the unit is firmly fixed to avoid

vibration and slipping off during operation. Ensure that the trussing or area of installation must be

able to hold 10 times the weight without any deformation. Always install a safety cable that can

hold at least 12 times the weight of the fixture when installing.

DO install and operate by qualified operator. It must be installed in a place where there is out of the

reach of people.

2. Technical Specifications

Power Voltage:

100-240V~ 50/60Hz

Power Consumption:

610W

Light Source:

37x20W RGBW LED

Zoom Range:

10°~60°

Movement:

Pan: 540°

Tilt: 270°

Pan/Tilt Resolution: 16bit

Dimming/Strobe:

0~100% smooth dimming, variable strobe speeds

Control:

DMX Channel: 14/26/15 Channels

Control Mode: DMX512, RDM

Firmware Upgrade: Update via DMX link

Construction:

Display: LCD display

Data In/Out: 3-pin & 5-pin XLR

Power In/Out: Power Connector in/out

Protection Rating: IP20

Features:

Electronic linear zoom system

Ring control, outstanding color macro effect

Dimension/Weight:

430x246x512mm, 19.5kgs

17"x9.7"x20"in, 42.9lbs

Photometric Diagram:

3. How To Set The Unit

3.1 Control Panel

1. Display: To show the various menus and the selected functions

2. LED:

POWER

Power on

DMX

DMX input present

3. Button:

To enter into move backward or leave the menu

DOWN

To go forward in the selected functions

To go backward in the selected functions

ENTER

To confirm the selected functions

4. DMX IN:

For DMX512 link, use 3/5 -pin XLR cable to link the unit and the DMX controller

5. DMX OUT:

For DMX512 link, use 3/5-pin XLR cable to link the next units

6. POWERCON IN:

To connect to supply power

7. POWERCON OUT:

To connect to the next fixture

8. FUSE(T 10A):

Protects the unit from damage of over-voltage or short circuit

3.2 Main Function

Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until

the required function is shown on the monitor. Select the function by pressing the ENTER button.

Use the UP/DOWN button to choose the submenu, press the ENTER button to store and

automatically return to the last menu. Press the MENU button or let the unit idle 30 seconds to exit

menu mode.

The main functions are shown below:

DMX Functions

To select DMX Functions, press the ENTER button to confirm, use the UP/DOWN button to select

DMX Address, DMX Channel Mode or View DMX Value.

DMX Address

To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to adjust the

address from 001 to 499/487/498, press the ENTER button to setup. Press the MENU button back to

the last menu or let the unit idle 30 seconds to exit menu mode.

DMX Channel Mode

To select DMX Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to

select Mode1 (14), Mode2 (26) or Mode3 (15), press the ENTER button to setup. Press the MENU

button back to the last menu or let the unit idle 30 seconds to exit menu mode.

View DMX Value

To select View DMX Value, press the ENTER button to confirm. Use the UP/DOWN button to view

the DMX channel values. Press the MENU button back to the last menu or let the unit idle 30

seconds to exit menu mode.

Fixture Setting

To select Fixture Setting, press the ENTER button to confirm, use the UP/DOWN button to select

Pan Inverse, Tilt Inverse, P/T Feedback,BL.O. P/T Moving, White Balance, Cooling Mode,Dimmer

Curve or Dimmer Speed.

Pan Inverse

To select Pan Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select No

(normal) or Yes (pan inverse), press the ENTER button to setup. Press the MENU button back to the

last menu or let the unit idle 30 seconds to exit menu mode.

Tilt Inverse

To select Tilt Inverse, press the ENTER button to confirm. Use the UP/DOWN button to select No

(normal) or Yes (tilt inverse), press the ENTER button to setup. Press the MENU button back to the

last menu or let the unit idle 30 seconds to exit menu mode.

P/T Feedback

To select P/T Feedback, press the ENTER button to confirm. Use the UP/DOWN button to select No

(Pan or tilt’s position will not feedback while out of step) or Yes (Feedback while pan/tilt out of step),

press the ENTER button to setup. Press the MENU button back to the last menu or let the unit idle

30 seconds to exit menu mode.

BL.O. P/T Moving

To select BL.O. P/T Moving, press the ENTER button to confirm. Use the UP/DOWN button to select

No (normal while pan/tilt moving) or Yes (blackout while pan/tilt moving), press the ENTER button

to setup. Press the MENU button back to the last menu or let the unit idle 30 seconds to exit menu

mode.

White Balance

To select White Balance, press the ENTER button to confirm. Use the UP/DOWN button to select

Red, Green or Blue. Once selected, press the ENTER button to confirm, and use the UP/DOWN

button to adjust the value from 125 to 255, press the ENTER button to setup. Press the MENU

button back to the last menu or let the unit idle 30 seconds to exit menu mode.

Cooling Mode

To select Cooling Mode, press the ENTER button to confirm. Use the UP/DOWN button to select

Auto or Silent. Once selected, press the ENTER button to setup. Press the MENU button back to the

last menu or let the unit idle 30 seconds to exit menu mode.

Dimmer Curve

To select Dimmer Curve, press the ENTER button to confirm. Use the UP/DOWN button to select

Linear, Square Law, Inverse Squ. or S-Curve. Once selected, press the ENTER button to store. Press

the MENU button back to the last menu or let the unit idle 30 seconds to exit menu mode.

Linear: The increase in light intensity appears to be linear as DMX value is increased.

Square Law: Light intensity control is finer at low levels and coarser at high levels.

Inverse Square Law: Light intensity control is coarser at low levels and finger at high levels.

S-Curve: Light intensity control is finger at low levels and high levels and coarser at medium levels.

This manual suits for next models

Table of contents

Popular Lighting Equipment manuals by other brands

Brizo

Brizo 8SP-MU-4 manual

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 installation instructions

IKEA

IKEA BJÖRKSPIREA manual

Laserworld

Laserworld Evolution Series ES-400RGB manual

Alien

Alien RG STAR user manual

EuroLite

EuroLite LED B-40 user manual

Qazqa

Qazqa Suplux SL 3 Black 103062 instruction manual

Commercial Electric

Commercial Electric 54568141 Use and care guide

CREE LIGHTING

CREE LIGHTING 304 Series installation instructions

Goobay

Goobay 49867 user manual

ECOMAN ITALIA

ECOMAN ITALIA LED T8 instruction manual

Alkalite

Alkalite Krypton KT-81 user manual

Clas Ohlson

Clas Ohlson GU10 manual

DTS

DTS DELTA 10 F user manual

ring

ring Solar Steplight manual

One Stop Gardens

One Stop Gardens 57696 Owner's manual & safety instructions

Chauvet DJ

Chauvet DJ COREpar UV120 ILS user manual

SIREM

SIREM Swimeo A2 instructions