ABB GE GEH4576 User manual
Description
Provides remote circuit breaker trip indication
using a single pole double throw switch
actuated by the breaker mechanism.
NOTE: Bell alarm cannot be installed in left
pole of circuit breaker models earlier than Jan
1, 1979 (date code D901*). Refer to factory
if in doubt.
Installation
CAUTION: The breaker must be completely
de energized and disconnected from the
electrical circuit, when the bell alarm is being
installed. This is mandatory because the
breaker must be in the ON position while the
accessory is being installed.
Place the breaker in a TRIPPED position
(handle at midpoint) by rotating trip button.
Remove cover mounting screws (4) and
handle (Figure 2).
—
Figure 1
—
Figure 2
1
GEH4576 INSTALLATION INSTRUCTIONS
Bell Alarm Switch Accessory
For Types TED, THED
4 COVER SCREWS
(8 FOR THLC1 AND
TLB1)
1.
2.
Note position of accessory mounting holes.
(Figure 3).
Install accessory as shown (Figure 4).
Adjust switch lever so that it actuates switch
within dimension shown with circuit breaker
in reset position. Trip the breaker by pushing
trip bar forward. Switch should actuate. if
not, readjust.(Figure 4).
Make two notches in cover, one for lever
clearance, and one for lead exit as shown in
Figure 5. Affix identification label.
Replace handle and breaker cover, taking care
not to pinch wires or switch lever between
cover and case.
Check continuity of bell alarm switch as
shown in Figure 6. Repeat Step 5 if necessary.
CIRCUIT
BREAKER
IN RESET OR
OFF POSITION
—
Figure 3
—
Figure 4
2
.01" TO .03" TRAVEL MUST
ACTUATE SWITCH
3.
4.
5.
6.
7.
8.
—
Figure 6
—
Figure 5
NOTE: UL listing is voided when the
ciicuit breaker is modified to add an
accessory.
3
—
ABB Inc.
305 Gregson Drive
Cary, NC 27511.
electrification.us.abb.com
—
We reserve the right to make technical
changes or modify the contents of this
document without prior notice. With
regard to purchase orders, the agreed
particulars shall prevail. ABB Inc. does not
accept any responsibility whatsoever for
potential errors or possible lack of
information in this document.
We reserve all rights in this document and
in the subject matter and illustrations
contained therein. Any reproduction or
utilization of its contents – in whole or in
parts – is forbidden without prior written
consent of ABB Inc.
Copyright© 2019 ABB
All rights reserved
—
GE is a trademark of GE. Manufactured
by ABB Inc. under license from GE.
1SQC930049M0201, GEH4576 February 2020
These instructions do not purport to cover all details or variations in equipment nor to provide for every
possible contingency to be met in connection with installation operation or maintenance. Should further
information be desired or should particular problems arise which are not covered sufficiently for the
purchaser’s purposes, the matter should be referred to the ABBCompany.
Table of contents
Other ABB Security System manuals
ABB
ABB SACO 16D1 User manual
ABB
ABB Welcome M2303 User manual
ABB
ABB M2131xPx-A series User manual
ABB
ABB 83327-500 User manual
ABB
ABB Arc Guard System TVOC-2 Product manual
ABB
ABB M2231 SERIES User manual
ABB
ABB FIM 1300 Series User manual
ABB
ABB Welcome M2303 User manual
ABB
ABB Welcome M21311P1-A Setup guide
ABB
ABB SAS-W1.1E User guide
Popular Security System manuals by other brands
EDM
EDM Solution 6+6 Wireless-AE installation manual
Highway Safety Group
Highway Safety Group EA401 user manual
Siren
Siren LED GSM operating manual
Detection Systems
Detection Systems 7090i Installation and programming manual
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 instructions
Siemens
Siemens FDM273 manual