ABB SREA-01 Troubleshooting guide

ABB Drives

Quick Start-up Guide

SREA-01 Ethernet Adapter Module

3AUA0000042902 Rev A

Effective: 01.10.2008

©2008 ABB Oy. All rights reserved.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

SREA-01 Quick Start-up Guide

2

SREA-01 Quick Start-up Guide

1. Connecting power and network

Connect 9–28 V AC/DC to Vin+ and Vin-.

Connect a cross-over Ethernet cable directly to the unit for start-

up. You can use a network after you have configured the unit.

2. Connecting to SREA-01 over Ethernet

The default Ethernet configuration is:

IP address: 10.200.1.1

Subnet mask: 255.255.255.0

Username: admin

Password: admin

Connection method 1:

Configure your PC to the same subnet (e.g. IP address 10.200.1.2

and subnet mask 255.255.255.0).

Use Internet Explorer or Mozilla Firefox and go to location

http://10.200.1.1.

Connection method 2:

Install the ABB IP Configuration Tool from the attached CD. When

you start the program, it will search for connected SREA-01

modules. You can change the network settings of the module by

double clicking it.

Use Internet Explorer or Mozilla Firefox and go to location

http://<ip of the SREA-01 module>, e.g. http://10.200.1.1.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

SREA-01 Quick Start-up Guide

3

3. Connecting drive(s)

If you have a single ACS350, ACH550 or ACS550, it is easiest to

use the supplied RJ45 cable to connect to the panel port.

If you have multiple drives or an ACS800, use the RS-485

connection. Connect the A- channels of the SREA-01 unit and the

drives together, the B+ channels together and the COM connector

to the data ground connectors of the drives. Use 120 ohm

terminating resistors in the network.

4. Basic drive settings

Check the communication settings of the drive (either group 52 or

53 in most drives, depending on the connection type).

Station id/number has to be unique for each drive! The baud rate

selection and parity have to be same on all drives and

SREA-01. You can use for example 9600 bit/s, no parity, 1 stop bit.

5. Basic SREA-01 settings

You can change the Ethernet settings under Setup – Ethernet.

Select the correct drive connection settings under Setup –

Modbus.

• Select Physical Interface.

• Usually most other settings are suitable by default (RTU,

9600 bps, no parity, 1 stop bit).

SREA-01

X1 pin Wire

Panel port

RJ45 pin

RX (RS-232) white-orange 1

TX (RS-232) white-blue 3

COM orange and blue 2 and 6

X1 RS-232: Select EIA-232

X1 RS-485: Select EIA-485

X2: Select EIA-232 D-sub

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

SREA-01 Quick Start-up Guide

4

To search for connected drives, go to page Configuration –

Devices and select autodetect.

6. More information

For more detailed information, please refer to the SREA-01 User’s

Manual located on the attached CD-ROM.

Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: [email protected]

Other manuals for SREA-01

1

Table of contents

Popular Control Unit manuals by other brands

Festo

Festo Compact Performance CP-FB6-E Brief description

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Quick installation guide

JS Automation

JS Automation MPC3034A user manual

JAUDT

JAUDT SW GII 6406 Series Translation of the original operating instructions

Spektrum

Spektrum Air Module System manual

BOC Edwards

BOC Edwards Q Series instruction manual

KHADAS

KHADAS BT Magic quick start

Etherma

Etherma eNEXHO-IL Assembly and operating instructions

PMFoundations

PMFoundations Attenuverter Assembly guide

GEA

GEA VARIVENT Operating instruction

Walther Systemtechnik

Walther Systemtechnik VMS-05 Assembly instructions

Altronix

Altronix LINQ8PD Installation and programming manual

Eaton

Eaton Powerware Series user guide

WAGO

WAGO 750-407/040-000 manual

Sony

Sony CCU-590 Operation manual

Graco

Graco 25D614 instructions

Task Force Tips

Task Force Tips YE-RF-900 Instructions for installation, safe operation and maintenance

Shini

Shini SPV-U Series manual