ABB FEPL-02 Ethernet POWERLINK User manual
Safety instructions
WARNING! Obey the safety instructions of the drive. If you ignore them, injury or death, or
damage to the equipment can occur.
Mechanical installation
Electrical installation
Layout of the module
1. Pull out the lock.
2. Install the module carefully to an option
module slot of the drive. See the drive
hardware manual.
3. Push in the lock.
4. Tighten the screw to torque 0.8 N·m
using a Torx TX10 screwdriver.
13
4
WARNING! Do not use excessive force, or leave the screw too loose. Over-tightening can
damage the screw or module. A loose screw decreases the EMC performance, and can
cause an operation failure.
No. Description
1Lock
2 Mounting and grounding screw
3 RJ-45 connector [X1]
4 RJ-45 connector [X2]
5 Diagnostic LEDs
6 MAC address
5
3
2
4
1
6
—
OPTIONS FOR ABB DRIVES
FEPL-02 Ethernet POWERLINK adapter
module
Quick installation and start-up guide
Connection procedure
Connect the network cables to connectors [X1] and [X2] on the module.
1. Connect the cable from the master to the left port [X1].
2. In the line topology, if there are more slave devices in the same line, connect the next slave
device to the right port [X2].
Start-up
To control the drive with the adapter module, set at least the basic parameters listed in the table
below. For full parameter descriptions, refer to the adapter module’s user manual or to the drive’s
firmware manual.
Basic parameter settings
To take the settings into use, validate and refresh the parameters with parameter 51.27 FBA par
refresh.
Further information
Index Name Value
20.01 Ext1 commands Fieldbus A
22.11 Speed ref1 source FBA A ref 1
28.11 Frequency ref1 source FBA A ref 1
50.01 FBA A enable Enable (or select the option slot in which the module is installed). This
activates the communication module. The HOST LED becomes green.
50.02 FBA A comm loss func Fault
51.02 Profile The CANopen device profile (CiA 402) is the default value.
See the latest version of FEPL-02 Ethernet POWERLINK adapter
module user's manual (3AUA0000123527 [English]) in ABB library
(www.abb.com/drives/documents).
For more information on ABB fieldbus options and protocols,
see the fieldbus communications web page
(new.abb.com/drives/connectivity/fieldbus-connectivity).
FEPL-02 manual
Fieldbus communications web
page
© Copyright 2023 ABB. All rights reserved.
Specifications subject to change without notice.
3AXD50000158164 Rev B (EN) 2023-01-25
abb.com/drives
Other manuals for FEPL-02 Ethernet POWERLINK
2
Other ABB Adapter manuals
ABB
ABB WBCA Series User manual
ABB
ABB AC 31 Installation and operating instructions
ABB
ABB Unifix AD Manual
ABB
ABB 520ADD02 User instructions
ABB
ABB RCNA-01 User manual
ABB
ABB FBIP-21 BACnet/IP Installation manual
ABB
ABB Tina 3A/Aps User manual
ABB
ABB SPA-ZC 400 Guide
ABB
ABB SPA-ZC 400 User manual
ABB
ABB REPL-01 User manual
ABB
ABB SLTA Option Card Serial LonTalk Product manual
ABB
ABB RDNA-01 User manual
ABB
ABB Busch-AudioWorld Busch-iDock 8218 U-500 User manual
ABB
ABB FEIP-21 Installation manual
ABB
ABB FDNA-01 User manual
ABB
ABB FMBT-21 User manual
ABB
ABB MTQ22-FBP User manual
ABB
ABB RS485 Modbus adapter Installation manual
ABB
ABB FENA-01 User manual
ABB
ABB CCA-01 User manual
