3idee le-idc3 User manual
www.3idee.eu
le-idc3 VESA adapter
Assembly instructions
The VESA adapter is compatible with the following products from Lenovo
(lenovo.com):
IdeaCentre AIO 3 27 (R3-Windows 11 Home-8GB-512GB), IdeaCentre AIO
3 27 (R5-Windows 11 Home-16GB-512GB), IdeaCentre AIO 3 27
(R7-Windows 11 Home-16GB-1TB), IdeaCentre AIO 3 Gen 6, IdeaCentre
AIO 3i 24 (i5-Windows 11 Home-16GB-512GB)
The VESA adapter allows you to conveniently mount your LENOVO brand All-in-
One PC to a monitor arm with a VESA hole pattern (75 x 75mm). Use the included
screws and nuts for this.
If you want to mount your VESA adapter directly to the wall, use suitable screws
and dowels (not included).
Make sure that the device is switched off and disconnected from the
mains to avoid possible injury or damage
2
Assembly instructions
Assembly instruction
Step 1
Place your Lenovo All-in-One PC securely on a soft surface.
Now remove the base of your Lenovo monitor if it is attached.
Step 2
Figure 1
Position your 3idee VESA adapter with the arrow and text
"UP" so that it is visible to you and with the arrow pointing
towards the top edge of the screen.
(Figure 1)
Step 3
Figure 2
Attach the VESA adapter to the monitor mount as shown.
(Figure 2)
Step 4
Figure 3
Take the 4 supplied M3x14 pan-head screws (separate screw
bag) and attach the adapter to the monitor.
(Figure 3)
3Assembly instructions
Step 5
Figure 4
For this step we recommend a 2nd person.
Now lift the monitor and hold it to your monitor mount.
Fasten the VESA adapter with the 4 included M4x14 screws
(screw bag: SP2).
It is best to fasten 2 screws diagonally first, so that the
monitor cannot fall down and you can fasten the remaining
screws without any effort.
ATTENTION: Pay attention to the right screws!
(Figure 4)
Step 6
Figure 5
Tighten the screws firmly. Done! (Figure 5)
4
Assembly instructions
Safety instructions
General notes
Make sure that all screws are tight and that the monitor audibly clicks into place during installation (if
present).
The material of the adapter is not heat resistant. Avoid direct heat around the adapter such as PC
exhaust or direct sunlight in summer.
PLA is UV resistant but not suitable for high temperatures.
Avoid jerky movements (pulling, tearing) on the PC monitor. This can affect the performance of the
VESA adapter.
Do not subject the PC monitor to excessive loads such as leaning or pushing. This can impair the
performance of the VESA adapter.
Material Notes
The adapter is made of high-quality polylactide (PLA) plastic. PLA is both a colorfast and UV-resistant
material and has low flammability. Polylactide has a low temperature resistance of approx. 35°C- 40°C
and is therefore not suitable for use in the vicinity of direct heat and heat sources.
Important note: Due to the low temperature resistance, the adapter is not suitable for use in vehicles
such as mobile homes or caravans. The temperatures prevailing there could affect the material and
impair the functionality of the adapter.
We wish you a lot of fun with your product.
Your 3idee Team
Responsible for this content:
3idee Technologies S.à r.l
5, ZA Um Lenster Bierg
L-6125 Junglinster
Luxembourg
Powered by TCPDF (www.tcpdf.org)
Table of contents
Other 3idee Adapter manuals
3idee
3idee le-idc3 User manual
3idee
3idee acr-s24 User manual
3idee
3idee ass-mxaq User manual
3idee
3idee smsng-cfg70 User manual
3idee
3idee de-sdc User manual
3idee
3idee hp-pro-g6 User manual
3idee
3idee de-sdc User manual
3idee
3idee 24B1H User manual
3idee
3idee de-aw34 User manual
3idee
3idee smsng-s24d User manual
3idee
3idee xia-27dm User manual
3idee
3idee smsng-g7 User manual
3idee
3idee de-se2417 User manual
3idee
3idee ox-mag User manual
3idee
3idee hp2i-o User manual
3idee
3idee hp-34f User manual
3idee
3idee VESA xia-1c User manual
3idee
3idee smsng-og9 User manual
3idee
3idee hp-x User manual
3idee
3idee ass-vz VESA User manual
