3idee de-se2417 User manual
www.3idee.eu
de-se2417 VESA Adapter
Assembly instructions
The VESA adapter is compatible with the following products from Dell (dell.com):
S2216M, S2316H, S2316M, S2317HJ, S2416H, S2717Q, S2817Q, SE2216H,
SE2416H, SE2416HSC, SE2416HX, SE2716H, SE2716H, SE2717HR,
SE2717HX and SE2417HGX.
The VESA adapter allows you to conveniently mount your DELL brand monitor to a
monitor arm with a VESA hole pattern (75 x 75mm). Use the included screws and
nuts.
If you want to mount your VESA adapter directly to the wall, use suitable screws
and dowels (not included).
2
Assembly instructions
Assembly instruction
Step 1
Place your screen in a safe, soft place so that your screen
does not get damaged.
Remove the base of your monitor if it is already attached.
Use a screwdriver and press it into the white dot above the
base.
Figure
Step 2
Slide the VESA adapter into the screen as shown. (Figure 1)
When you hear a "click" sound, the adapter has successfully
snapped into place and is securely connected to the screen.
To check: Pull a little on your adapter to test if it is properly
engaged.
Figure 1
Step 3
Check again if the VESA adapter is firmly connected to the
monitor. (Figure 2)
Figure 2
3Assembly instructions
Step 4
Now hold the VESA adapter on your monitor arm and screw
it tight from behind with the other hand. (Figure 3)
Figure 3
Step 5
When fully assembled, it should now look as shown. (Figure
4)
Figure 4
4
Assembly instructions
Safety instructions
General notes
Make sure that all screws are tight and that the monitor audibly clicks into place during installation (if
available).
The material of the adapter is not heat resistant. Avoid direct heat around the adapter such as PC
exhaust or direct sunlight in summer.
PLA is UV resistant but not suitable for high temperatures.
Avoid jerky movements (pulling, tearing) on the PC monitor. This can affect the performance of the
VESA adapter.
Do not subject the PC monitor to excessive loads such as leaning or pushing. This can impair the
performance of the VESA adapter.
Material Notes
The adapter is made of high-quality polylactide (PLA) plastic. PLA is both a colorfast and UV-resistant
material and has low flammability. Polylactide has a low temperature resistance of approx. 45°C-55°C
and is therefore not suitable for use in the vicinity of direct heat and heat sources.
We wish you a lot of fun with your product.
Your 3idee Team
Responsible for this content:
3idee Technologies S.à r.l
5, ZA Um Lenster Bierg
L-6125 Junglinster
Luxembourg
Powered by TCPDF (www.tcpdf.org)
Table of contents
Other 3idee Adapter manuals
3idee
3idee hp2i-o User manual
3idee
3idee hp-s User manual
3idee
3idee smsng-s27d User manual
3idee
3idee smsng-g7 User manual
3idee
3idee hp-z32 User manual
3idee
3idee smsng-cv27 User manual
3idee
3idee hp2x-o User manual
3idee
3idee de-aw34 User manual
3idee
3idee S2216M User manual
3idee
3idee vs-vx24 User manual
3idee
3idee smsng-s32bm User manual
3idee
3idee hp-mh User manual
3idee
3idee Q-ew27 User manual
3idee
3idee 24V2Q User manual
3idee
3idee smsng-s24b User manual
3idee
3idee csl-f24 User manual
3idee
3idee de-sdc User manual
3idee
3idee Q-E32003R User manual
3idee
3idee hp-pav User manual
3idee
3idee MSI - G241VC-017 User manual
