ZKTeco SF1008+ User manual
Quick Start Guide
SF1008+
Version: 1.0
Date: April 2020
1
1Overview
8-inch touchscreen
Camera & palm collector
Speaker
Reset button
Flash
Exit
button
Auxiliary
input
AUX
AL+
AL-
NC
COM
NO
BUT
GND
SEN
GND
Alarm
Lock
Sensor
GND
+12V Power
GND
INWD0
INWD1
Wiegand
In
Wiegand
Out
12V
GND
WD0
WD1
Networkinterface
RS232
RS485
12V
485B
485A
GND
TXD1
RXD1
GND
GND
GND
12V
12V
Power
interface
Tamper switch
Near-infrared flash
Thermal infrared temperature
measurement module
Microphone (Optional)
2
①
②
3
3 Device Installation
①Attach the mounting template sticker to the wall, and drill holes according to the mounting
paper.
②Fix the back plate on the wall using wall mounting screws.
③Attach the device to the back plate.
④Fasten the device to the back plate with a security screw.
Install on the wall
1 2
4
1.5m
INDOOR USE
Please refer to the following recommendations for installation.
AVOID DIRECT
SUNLIGHT
AND EXPOSURE
KEEP DISTANCE AVOID GLASS
REFRACTION
KEEP EFFECTIVE
DISTANCE
20-50cm
10ft
6.5ft
window
2 Installation Environment
Install on the barrier gate
Please thread the wire through the bracket before installation.
①Drill a hole on the barrier gate, insert the bracket into the hole and fix it with a nut.
②Adjust the angle of the device.
3
3 Device Installation
1
2
①
②
4
4 Standalone Installation
Alarm Smoke
detector
Lock TCP/IP
Exit button
Door sensor
Reader
PC
5 Door Sensor, Exit Button & Alarm Connection
Door sensor
Alarm power
Alarm
-
+
-+
-+
-+
Detector power
Smokedetector
Exitbutton
AUX
AL+
AL-
NC
COM
NO
BUT
GND
SEN
GND
GND
5
6 Lock Relay Connection
The system supports Normally Opened Lock and Normally Closed Lock.
The NO LOCK (normally unlocked when power-on) is connected with 'NO' and 'COM' terminals, and
the NC LOCK (normally locked when power-on) is connected with 'NC' and 'COM' terminals.
Take NC Lock as an example below:
1)Device not sharing power with the lock
Normally Closed Lock
DC12V
DC12V
2)Device sharing power with the lock
+12V
GND
FR107
FR107
Normally Closed Lock
GND
AUX
GND
SEN
GND
BUT
NO
COM
NC
AL-
AL+
DC12V
+12V
GND
GND
AUX
GND
SEN
GND
BUT
NO
COM
NC
AL-
AL+
7 Wiegand Reader Connection
Access controller
+12V
GND
Wiegand reader
INWD0
INWD1
12V
GND
WD0
WD1
Maximum DC12V input.
6
8 Barrier Connection
9 RS485 Connection
Barrier gate
+12V
GND
GND
485+
485-
12V
485B
485A
GND
TXD1
RXD1
GND
GND
GND
12V
12V
485 reader
12V
485B
485A
GND
TXD1
RXD1
GND
GND
GND
12V
12V
Note: 485A and 485B can be connected to the barrier gate or the 485 reader, but cannot be
connected to the gate and the reader at the same time.
11 Ethernet Connection
Connect the device and computer software over an Ethernet cable. An example is shown below:
: 192.168.1.201Default IP address
: 255.255.255.0 Subnet mask
: 192.168.1.130IP address
: 255.255.255.0 Subnet mask
Note: In LAN, IP addresses of the server (PC) and the device must be in the same network segment
when connecting to ZKBioAccess EP software.
Click on [Comm.] > [Ethernet] > [IP Address], input the IP address and click on [OK].
10 Power Connection
12V3ADC
Recommended power supply: 12V - 3A
To share the power with other devices, use a power supply with higher current ratings.
7
ZKBioAccessEP
12 UserRegistration
8
Method1: Register on the device
Clickon> [User Mgt.] > [New User] to register a new user. Settings include entering user ID and
name, registering palm, face, password and user photo, setting user role and access control role.
When there is no super administrator set in the device, click on to enter the menu. After setting the
super administrator, the system will request for the administrator’s verification before entering the menu.
For the security purpose, it is recommended to register a super administrator at the first time you use
the device.
LL
L
Enroll Palm
9
Method 2: Register on ZKBioAccess EP software
Please set the IP address and cloud service server address on the device.
2. Click [Personnel] > [Person] > [New] to register users in the software.
3. Add users to access levels.
4. Click [Access] > [Device] > [Device Control] > [Synchronize All Data to Devices].
For more details, please refer to the ZKBioAccess EP User Manual.
1. Click [Access] > [Access Device] > [Device] > [Search Device] to add the device to the software.
When the device has set the server address and port, it can be added automatically.
Step1
Step2
Step3
Step4
Table of contents
Other ZKTeco Security System manuals
ZKTeco
ZKTeco FaceDepot-7BL User manual
ZKTeco
ZKTeco OP-400 User manual
ZKTeco
ZKTeco ZKX6550 User manual
ZKTeco
ZKTeco X7 User manual
ZKTeco
ZKTeco DM10 User manual
ZKTeco
ZKTeco SpeedFace Series User manual
ZKTeco
ZKTeco FR1200 User manual
ZKTeco
ZKTeco ProBio User manual
ZKTeco
ZKTeco FMD Pro 2.0 User manual
ZKTeco
ZKTeco RF100 User manual
Popular Security System manuals by other brands
EDM
EDM Solution 6+6 Wireless-AE installation manual
Highway Safety Group
Highway Safety Group EA401 user manual
Siren
Siren LED GSM operating manual
Detection Systems
Detection Systems 7090i Installation and programming manual
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 instructions
Siemens
Siemens FDM273 manual