ZKTeco X7 User manual

Produced by ZKTeco Inc.

System User Manual

X7 Access Control

Поставщик систем безопасности: TELECAMERA.RU

Wall mount installation

Access Control System Function:

(1)If a registered user verified, the device will

export the signal to unlock the door.

(2)Door sensor will detect the on-off state. If the

door is unexpected opened or improperly closed,

the alarm signal (digital value) will be triggered.

(3)If the device being illegally removed, the device

will export alarm signal.

(4)External exit button is supported; it is

convenient to open the door inside.

(5)External bell is supported.

1. Equipment Installation

(4)Fix the device to the back

cover.

(5)Fix the screw.

(1)Remove the screw on the

bottom of device.

(2)Take away the back cover.

(3)Fix the back cover on the wall

according to the mounting paper.

2. Structure and Function

Поставщик систем безопасности: TELECAMERA.RU

Warning: No operation when power on!

(1) The system supports NO LOCK and NC LOCK. For example the NO LOCK

(normally open at power on) is connected with ‘NO’ terminal, and the NC LOCK is

connected with ‘NC’ terminal.

(2) When the Electrical Lock is connected to the Access Control System, you need

to parallel one FR107 diode (equipped in the package) to prevent the

self-inductance EMF affect the system, do not reverse the polarities.

(I) Share power with the lock:

(II) Does not share power with the lock:

I①: ‘I’: device output current, ‘ULOCK’: lock voltage,’ ILOCK’: lock current.

Device share power with the

lock:

ULOCK=12V, I-ILOCK>1A……



And the lock is near to the

device.

Device does not share power

with the lock:

A. ULOCK =12V I-ILOCK ≤1A;

B. ULOCK ≠12V;

C. The lock is far apart from the

device.

3. Lock Connection

Поставщик систем безопасности: TELECAMERA.RU

Voltage output ≤ DC 12V for Alarm

Input DC 12V, 500mA (50mA standby)

Positive is connected with ‘+12V’, negative

is connected with ’GND’ (do not reverse the

polarities).

4. Connected with Other Parts

5. Connect with Power

Поставщик систем безопасности: TELECAMERA.RU

Instructions

Recommended Procedure:

Step 1: Install the device and power on.

Step 2: After the administrator password is authenticated and changed, register

users' fingerprints, cards, or passwords.

Step 3: Configure access control parameters, including modifying eight

passwords for opening the door and configuring the unlocking duration,

authentication mode, stealth mode, door status sensor mode, and alarm.

Functions of the Device

∣―1.User Management

∣∣―1.1 Administrator Operations

∣∣∣―Administrator Authentication

∣∣∣―Change Administrator Password

∣∣∣―Open the Door by the Administrator Password

∣∣∣―Administrator Password Be Forgotten

∣∣―1.2 Add Users

∣∣∣―Add Users

∣∣∣―Register Cards in Batches

∣∣―1.3 User Authentication

∣∣―1.4 Delete Users

∣∣∣―Delete a User

∣∣∣―Delete All Users

∣―2.Access Control Management

∣∣―2.1 Set/Change Eight Passwords for Opening the Door

∣∣―2.2 Configure Unlocking Duration

∣∣―2.3 Configure Authentication Mode

∣∣―2.4 Configure Concealed Mode

∣∣―2.5 Configure Door Sensor Mode

∣∣―2.6 Configure Alarm

∣∣∣―Configure Alarm setting

∣∣∣―Configure Error Operation-Triggered Alarm

∣∣∣―Configure Tamper Alarm

∣∣∣―Configure Alarm Delay for the Door Status Sensor

Поставщик систем безопасности: TELECAMERA.RU

Operation Instructions

1. User Management

1.1 Administrator Operations

To ensure data security of the device, you can operate the device only after the

administrator password is authenticated.

Administrator Authentication

1. Press [*]

(The indicator is off and

makes a long beep.)

2. Press[ #].

(You can authenticate the

password.)

3. Enter the administrator

password.

(The initial password is

1234.)

5. Exit.

(Press * or do not operate

the device within 20

seconds.)

4. The authentication is

successful.

(The indicator turns green.)

Note: The initial administrator password is 1234. You are advised to change

the initial password at the beginning.

Change Administrator Password

1. The administrator

password is authenticated.

2. Press 8.

(You can change the

password.)

3. Enter a new

administrator password.

YES

5. Succeeded.

(The indicator turns

green and makes a long

beep.)

4. Enter the new

administrator password

again for authentication.

6. Exit.

(The device automatically

exits the process when the

operation is completed.)

Failed.

(The indicator turns red

and makes three

beeps.)

Note: Four-digit passwords are automatically verified. For passwords with less

than four digits, press # to enter the verification process.

Open the Door by Entering the Administrator Password

Поставщик систем безопасности: TELECAMERA.RU

1. The administrator

password is authenticated.

2. Press 0.

(The indicator turns green

and makes a long beep.)

3. Press 0.

(The indicator turns green

and makes a long beep.)

5.Exit.

(The device automatically

exits the process when the

operation is completed.)

4. The door is opened

(The indicator turns green

and makes a long beep.)

Note: This function can be used to open the door.

Administrator Password Is Forgotten

If the administrator password is forgotten, you can press the tamper switch

three times to reset the password to the initial administrator password 30 to 60

seconds after the device is disassembled from the wall or door. (There is a long

beep 30 seconds after the device is disassembled from the wall or door.)

1.2 Add Users

Add Users

1. The administrator

password is authenticated.

2. Press 1.

(The indicator turns green

and makes a long beep.)

3. Register fingerprints or

cards. (Press fingers three

times to get a fingerprint or

swipe the card once.)

Yes

5. Exit.

(Press * to exit.)

4. Adding Users is

successful.

(The indicator turns green

and makes a long beep.)

Failed.

(The indicator turns red

and makes three beeps.)

Note: 1. In the registration process, the user ID increases automatically. The

device automatically enters the process of registering the next user when a user

is successfully registered.

2. The registration process fails if the fingerprint is of poor quality or the

fingerprint or the card has been registered. After the device indicator turns

Поставщик систем безопасности: TELECAMERA.RU

green, you can register the user again. Registered users must not be registered

again.

Register Cards in Batches

1. The administrator

password is authenticated.

2. Press 6.

(Registering Cards in

Batches)

3. Swipe the first card once

only.

5. Cards are successfully

registered in batches. 4. Enter the total number of

cards.

6. Exit.

(The device automatically

exits the process when the

operation is completed.)

Failed.

(The indicator turns red

and makes three beeps.)

YES

Yes

Note: 1. In the process of entering the total number of cards, three-digit

numbers are automatically verified. For numbers with less than three digits,

press # to enter the verification process. Press * to reenter the total number of

cards.

2. You must clear all the registered users before registering cards in batches. IDs

of to-be-registered cards must be consecutive numbers.

1.3 User Authentication

Authenticate Users' Fingerprints/Cards/Passwords

After the device is powered on, it enters the authentication state for users to

unlock the door.

Поставщик систем безопасности: TELECAMERA.RU

1. The device is in the

authentication state.

2. Press fingerprints, swipe

cards, or enter passwords.

Press # after entering a

password.

3. The authentication is

successful.

Yes

Failed.

(The indicator turns red

and makes three beeps.)

Note: Press # after entering a password for authentication. The door opens if

the entered password is identical with one of the eight passwords for opening

the door. The initial eight passwords for opening the door are empty. To change

passwords for opening the door, please refer to 2.1 Set/Change Eight Passwords

for Opening the Door.

1.4 Delete Users

Delete a user whose fingerprint or card is registered, or delete all users.

Delete a User

1. The administrator

password is authenticated.

2. Press2.

(The indicator turns green

and makes a long beep.)

3. Enter a user ID, press the

fingerprint, or swipe the

card.

YES

5. The user is deleted.

( The indicator turns green

and makes a long beep,

then turns red and makes a

long beep again.)

4. Determine whether the

user is authentic.

6. Exit.

(Press * or do not operate

the device within 20

seconds.)

Failed.

(The indicator turns red

and makes three beeps.)

Note: 1. In the process of entering user IDs, five-digit IDs are automatically

verified. For IDs with less than five digits, press # to enter the verification

process.

2. The device automatically enters the process of deleting the next user when a

Поставщик систем безопасности: TELECAMERA.RU

user is deleted.

3. The indicator turns red and makes a long beep in fifth step indicates system

exits when setting successfully.

Delete All Users

1. The administrator

password is authenticated.

2. Press 9.

(The indicator turns green

and makes a long beep.)

3. Press 9.

(The indicator turns green

and makes a long beep.)

5.Exit.

(The device automatically

exits the process when the

operation is completed.)

4. Deleting All Users is

successful.

( The indicator turns green

and makes a long beep,

then turns red and makes a

long beep again.)

Note: 1.Press 9 for automatic confirmation. Other values are considered

invalid. If an invalid value is entered, the device indicator turns red, and the

device makes a long beep and exits the process.

2. The indicator turns red and makes a long beep in fourth step indicates system

exits when setting successfully.

Поставщик систем безопасности: TELECAMERA.RU

Other manuals for X7

Table of contents

Other ZKTeco IP Access Controllers manuals

Popular IP Access Controllers manuals by other brands

Jantar

Jantar REX A-1-9 quick start guide

2N Access Unit Configuration manual

Kedacom

Kedacom KSCA120 Series quick start guide

H3C

H3C WX2880X installation guide

G4S

G4S S870-EX Installation and user instructions

PRASTEL

PRASTEL M2000PE manual

Allegion

Allegion interflex IF-281 Cylinder manual

TECOM

TECOM TS1067E manual

Fermax

Fermax Memokey 100C Installer manual

Fermax

Fermax CITYLINE MEMOKEY User& installer's manual

Software House

Software House iSTAR Pro 2U RM Quick start installation guide

AKCP

AKCP SP+ manual

Bpt

Bpt HNA/102 installation instructions

Civintec

Civintec CV9601T-T-1F installation manual

BioMax

BioMax N-X90W user manual

FingerTec

FingerTec s-Kadex user guide

H3C

H3C WX5002ACCESSCONTROLLER installation manual

C Prox Ltd

C Prox Ltd DPN-2 user manual