ZKTeco C2-260 User manual

Installation Guide

C2-260 Metal Cabinet

Version: 1.0

Due to regular upgrades of systems and products, ZKTeco could not guarantee exact consistency between the

actual product and the written information in this manual.

1 Cautions

Please note the following cautions. Mis-operation may lead to personal injury or equipment

failure:

1. Do not energize the system before installation is complete; never carry out installation activities when

the system is energized.

2. All peripheral devices must be grounded.

3. The conduits of wires under relay must be matched with metaled conduits, other wires can use PVC

conduits.

4. It is strongly recommended that the length of exposed part of any connection cable should not be

longer than 4 mm. Professional clamping tools may be used to avoid unintentional contact of exposed

wires to avoid short-circuit or communication failure.

5. It is recommended that card readers and buttons be installed at height of 1.4m-1.5m above ground.

6. It is recommended to use the power supply for control panel, and external power supply for each lock.

7. The appliance shall be installed and wired in accordance with national electrical code and by qualified

personnel only.

Description of normal working state:

Connect the system to the power supply. If the system works properly, the POWER indicator (red) is lit

constantly.

2 Control Panel Indicators

When the C2-260 is powered on, normally the POWER indicator (red) is lit constantly, the RUN indicator

(green) shall flash slowly (indicating the system is normal), and other indicators are all off.

COMM indicator (yellow): It flashes when the system is communicating with other devices (e.g., PC). When

the indicator is flashing continuously, it indicates data transmission. When the indicator is flashing slowly,

it indicates real-time monitoring status.

Product Dimension

C2-260 Aux485/WR485

C2-260 Metal Cabinet

330.0mm

364.6mm

75.7mm

Installation of Panel & Cabinet

C2-260 Panel

Heat Dissipation Hole

Aux485

Power Supply

Cable ConduitPower Indicator

(Punch Hole for cables)

MountingHoles

We recommend drilling the mounting plate screws into solid wood (i.e. stud/beam).

MountingHoles

5Internal Wiring Diagram

C2-260

Power Indicator

Aux485

Power Supply

LNG V-

V+

B-B+

12V Battery

(Prepared by the user)

Wiring Legend

1. The auxiliary input may connect to infrared body detectors, re alarms, or smoke detectors.

2. The auxiliary output may connect to alarms, cameras or doorbells, etc.

3. PC RS485 indicates the RS485 cable is connected to the DM10/AUX485 through this port. The RS485 Reader port can

be connected externally to RS485 reader.

4. Restore factory setting: The NO.4 of DIP switch is OFF by default. When it is moved up and down for three times

within 5 seconds and nally returned to OFF position, the factory settings will be restored after the access control panel

is restarted, and the IP address will restore to the default (192.168.1.201).

5. The terminals above are set through the relevant access control software. Please see the respective software manual for

further details.

Notes:

7AUX485 Connection

AUX485

+12V

485B

485A

AUX

DC12V

AUX485

+12V

485B

485A

AUX

DC12V

485A

485B

GND

Notes:

1. A C2-260 can connect to maximum two AUX485 modules.

2. Each AUX485 module can connect to maximum four auxiliary devices.

3. Each AUX485 module requires a separate power supply.

RS485 Reader Connection

RS485-

RS485+

GND

VCC

RS485 Reader

Note:

1. It’s recommended to connect maximum four readers to one C2-260.

2. A single RS485 reader interface can supply a maximum of 750 mA (12V) current. So the entire current

consumption should be less than this max value when the readers share the power with the panel.

Exit Button Connection

EXIT

GND

BUT

K2SExitButton

GND

V+

Normally Closed Lock

Lock Relay Connection

The system supports both Normally Opened Lock and Normally Closed Lock. The NO Lock (Normally

Opened when powered) is connected with 'NO' and 'COM' terminals, and the NC Lock (Normally Closed

when powered) is connected with 'NC' and 'COM' terminals. The power can be shared with the lock or can

be used separately for the lock, as shown in the example with NC Lock below.

Device not sharing power with the lock

GND

+12V DC COM

COM

GND

Maximum30V2Ainput.

FR107 Diode

TCP/IP

Device sharing power with the lock

+12V

Do not reverse

the polarity.

Do not reverse

the polarity.

Other manuals for C2-260

Table of contents

Other ZKTeco IP Access Controllers manuals

ZKTeco

ZKTeco MultiBio 700 User manual

ZKTeco

ZKTeco ProFace X Series User manual

ZKTeco

ZKTeco C3 User manual

ZKTeco

ZKTeco SC800 User manual

ZKTeco

ZKTeco C3 Pro User manual

ZKTeco

ZKTeco Notus User manual

ZKTeco

ZKTeco MB10-VL User manual

ZKTeco

ZKTeco MiniAC Plus User manual

ZKTeco

ZKTeco FR1200 Datasheet

ZKTeco

ZKTeco Green Label ProFace X User manual

ZKTeco

ZKTeco X6 Instruction sheet

ZKTeco

ZKTeco KF1000-U User manual

ZKTeco

ZKTeco SCR-100 Plus User manual

ZKTeco

ZKTeco VF Series User manual

ZKTeco

ZKTeco MultiBio 700 User manual

ZKTeco

ZKTeco ZKX5030A User manual

ZKTeco

ZKTeco MA500 Troubleshooting guide

ZKTeco

ZKTeco RevFace15 User manual

ZKTeco

ZKTeco SpeedFace-VSL Series User manual

ZKTeco

ZKTeco Atlas Bio Series User manual

ZKTeco

ZKTeco C5S120 Guide

ZKTeco

ZKTeco BioPro SA50 User manual

ZKTeco

ZKTeco ProCapture-T User manual

ZKTeco

ZKTeco BioServer 2 User manual

Popular IP Access Controllers manuals by other brands

Jantar

Jantar REX A-1-9 quick start guide

2N Access Unit Configuration manual

Kedacom

Kedacom KSCA120 Series quick start guide

H3C

H3C WX2880X installation guide

G4S

G4S S870-EX Installation and user instructions

PRASTEL

PRASTEL M2000PE manual

Allegion

Allegion interflex IF-281 Cylinder manual

TECOM

TECOM TS1067E manual

Fermax

Fermax Memokey 100C Installer manual

Fermax

Fermax CITYLINE MEMOKEY User& installer's manual

Software House

Software House iSTAR Pro 2U RM Quick start installation guide

AKCP

AKCP SP+ manual

Bpt

Bpt HNA/102 installation instructions

Civintec

Civintec CV9601T-T-1F installation manual

BioMax

BioMax N-X90W user manual

FingerTec

FingerTec s-Kadex user guide

H3C

H3C WX5002ACCESSCONTROLLER installation manual

C Prox Ltd

C Prox Ltd DPN-2 user manual