ZKTeco SA32-E User manual

Single Door RFID Based Access Control

SA32-E/M

Thank you for choosing our product. Please read the instructions

carefully before operation. Follow these instructions to ensure that the

product is functioning properly. The images shown in this manual are

for illustrative purposes only.

New Firmware for 2.8/3/3.5-inch Color Screen

Product Overview

SA32-E

Single Door RFID Based Access Control

SA32-E is an Access Control Standalone Device with contact-less

smart card and password verications, which enables 3 verication modes

(Card only, PIN only, and Card & PIN) to ensure maximum safety and

exibility. With 1 Relay output (optional) and 1 PUSH (low) output,

1 door button Port and 1 doorbell Port, SA32 is simple but eective to use,

its convenience and adaptability allow it to be well deployed in residential

housing, oces and any other public facilities.

1. Specifications:

1.1Technical parameters:

NO Item Value

Operating voltage

DC 12V±10%

Operating current

< 100mA

Dimensions

120mm×78mm×22mm

Weight

110g

Ambient temperature



—60



Relative humidity

20%—80%

Storage

1000users

Card type (alternative)

EM(ID) card(IC card for options)

Card reading distance

－

15CM

1.2 Factory Default:

1.3 Light and Sound indicates:

Light: red and green

Light Description

Access control status

Red light flash every 1 sec

（

Slow flash

）

Holding state

Red light is always ON

Programming state

Green light is always ON within Open time

Unlocking state

Green light flash every 0.5sec (Fast flash)

Pending further action

Sound ：buzz

Description

I ndicates

1 short buzz

Valid input

3 short buzz

Invalid input

1 long buzz

Program success

Continuous long buzz

Restoring factory programming passwords

Programming

Password

123456 Common Access

Password

None

Backlight Auto (for options) Relay Unlock

output 5 Seconds

W26 port Input (for options) Security mode OFF

Open mode

Card or Access Password

Access Password include Private Access Password (PIN) and

Common Access Password

2. Installations Guide

JP1 terminal:

JP2 terminal:

Mark

Color

Function

Remark

+12V

Red

Power+

For options

GND

Black

Power-

DATA0

Green

WG DATA0

DATA1

White

WG DATA1

Brown

Relay NC output

COM

Blue

Relay Com output

Purple

Relay NO output

Mark

Color

Function

+12V

Red

Power+

GND

Black

Power-

PUSH

BLUE

Low level output

OPEN

Yellow

Door Release

BELL

Grey

BELL

White

BELL

emark:

let relay drive electric -

“-” poles.

lock, please connect a reverse diode with the lock’s “+” and

Wiring diagram:

3.2 To reset to Factory Programming Password (123456)

Step1、Turn off power and connect bin 2&3 of RST(S1)。

Step2、Turn on power and buzzer gives 3 long buzz with green light flash fast。

If need to set Manager Card, now read two empty cards first one as Manager Add Card and

Second one as Manager Delete Card with red light flashing and continuous short buzz .

Step3、Turn off power, disconnect bin2&3 and connect bin 1&2 of RST。

Step4、Turn on power again.

3.3 How to use Manager Card - MAC & MDC

To add a card user in standby mode: read MAC read new cards read MAC

To delete a card user in standby mode: read MDC read registered cards read MDC

To delete all users in standby mode: read MDC read MAC read MDC

Remark: User cards can be added or deleted continuously.

3.4 User ID No. explain

User ID is auto-generating 4-digit number started at 0001. The number increases with adding

user one by one and ignores deleting user. Common Access Password has no ID.

3.5 How to change PIN (When open mode: card+ PIN)

After reading card and input corresponding PIN to open the door, within 5 seconds, long press #

until the green lights flash fast. and then input new PIN # new PIN # , new PIN

changed successfully with a long buzz.

3. Programming Guide

ZKTeco Biometrics India Pvt. Ltd. www.zkteco.in E-mail: [email protected]

This manual suits for next models

Table of contents

Other ZKTeco IP Access Controllers manuals

Popular IP Access Controllers manuals by other brands

Jantar

Jantar REX A-1-9 quick start guide

2N Access Unit Configuration manual

Kedacom

Kedacom KSCA120 Series quick start guide

H3C

H3C WX2880X installation guide

G4S

G4S S870-EX Installation and user instructions

PRASTEL

PRASTEL M2000PE manual

Allegion

Allegion interflex IF-281 Cylinder manual

TECOM

TECOM TS1067E manual

Fermax

Fermax Memokey 100C Installer manual

Fermax

Fermax CITYLINE MEMOKEY User& installer's manual

Software House

Software House iSTAR Pro 2U RM Quick start installation guide

AKCP

AKCP SP+ manual

Bpt

Bpt HNA/102 installation instructions

Civintec

Civintec CV9601T-T-1F installation manual

BioMax

BioMax N-X90W user manual

FingerTec

FingerTec s-Kadex user guide

H3C

H3C WX5002ACCESSCONTROLLER installation manual

C Prox Ltd

C Prox Ltd DPN-2 user manual