Yacht Devices YDTC-13 User manual
User Manual
Digital Thermometer YDTC-13
Digital Barometer YDBC-05
also covers models
YDTC-13R, YDTC-13RT, YDTC-13N, YDTC-13NT
YDBC-05R, YDBC-05RT, YDBC-05N, YDBC-05NT
Software version 1.22
2015
© 2015 Yacht Devices Ltd. Document YDBC05TC13-004. March 24, 2015.
Web: http://www.yachtd.com/
NMEA 2000® is a registered trademark of National Marine Electronics Association.
SeaTalk NG is a registered trademark of Raymarine UK Limited. Garmin® is a
registered trademark of Garmin Ltd.
Contents
Introduction .4
Warranty and Technical Support .6
Product Specication .7
Device Connection and Testing .9
Programming the Device 14
APPENDIX А. Troubleshooting 23
APPENDIX B. Description of Connectors and Joints 25
APPENDIX С. NMEA 2000 Messages 27
Package Contents
Device 1 pc.
This Manual 1 pc.
— 4 —
Introduction
This Manual contains information on how to install, congure and operate YDTC-13
digital thermometers (hereinafter Thermometer) and YDBC-05 digital barometers
(hereinafter Barometer) intended for using on pleasure crafts.
The Thermometer and Barometer (hereinafter, where the dierences are not
critical, Devices) have one digital sensor. Up to 50 devices may be used on a vessel
simultaneously; this limitation is set by the network specication. Data from the
Devices can be displayed on chartplotters, digital navigation instruments, as well as
used by other digital equipment of the vessel.
The Thermometer performs measurements within the range from -55 to +125 °С
(-67..+257 °F), the sensor is placed outside the case on a exible 95cm-long wire in a
sealed stainless steel sleeve and can be used to measure the temperature of gases and
liquids. The wire, if necessary, can be elongated up to 100 meters. The Thermometer
can be congured to display its data as "Air temperature", "Sea temperature",
"Temperature in the refrigerator", "Temperature in the engine room", etc.
The Barometer is intended for measuring atmospheric pressure within the range
from 300 to 1100 hPa (mbar). The sensor is located inside the device case. The
Barometer identier can be congured so that data from several Barometers will be
simultaneously displayed on a chartplotter.
The Devices are designed for operating in an NMEA 2000 network and are
compatible with a wide range of equipment supporting this protocol. Raymarine
SeaTalk NG, Simrad SimNet, Furuno CAN networks are branded versions of NMEA
2000 and dier only in the type of connectors. In its devices, Garmin uses the NMEA
2000 Micro connector which is compatible with the DeviceNet Micro connector. Our
— 5 —
Devices are supplied with dierent types of connectors, making it possible to connect
them to networks of dierent manufacturers without any adapters. The Device model
is shown on the case.
Device model Type of the connector, compatibility
(see Appendix B)
YDBC-05R, YDTC-13R Raymarine SeaTalk NG Female
YDBC-05RT,
YDTC-13RT Raymarine SeaTalk NG Female Terminator
YDBC-05N, YDTC-13N,
YDBC-05NT, YDTC-13NT
NMEA 2000 Micro Male, DeviceNet Micro Male,
Garmin NMEA 2000 Male
To connect to other types of NMEA 2000 networks, a cable adapter is required
(it is not supplied with the Device and must be purchased separately). Note that the
Devices are not compatible with the NMEA 0183 protocol.
According to the specication, an NMEA 2000 network has two terminators
(120-Ohm resistors) connected to the NMEA 2000 bus ends. Device models with the
T index at the end of their names contain a built-in terminator and should be
connected to the network instead of the terminator. This allows a zero-cost connection
of the Devices to existing networks with no free connectors. Please note that according
to the specication, you can not use more than two devices with the T index on one
NMEA 2000 bus.
We thank you for purchasing our Devices and wish you happy voyages!
— 6 —
Warranty and Technical Support
1. The Device warranty is valid for two years from the date of purchase. If a Device
was purchased in a retail store, when applying under a warranty case, the sale
receipt can be requested.
2. The Device warranty is terminated in case of violating the instructions of this
Manual, case integrity breach, repair or modication of the Device without
manufacturer’s written permission.
3. Modication of the Thermometer sensor cable is performed by the user at his own
risk, the warranty does not cover the Device failure in this case.
4. If a warranty request is accepted, the defective Device must be sent to the
manufacturer.
5. The warranty liabilities include repair and replacement of the goods and do not
include the cost of equipment installation and conguration, as well as shipping
the defective Device to the manufacturer.
6. Responsibility of the manufacturer in case of any damage as a consequence of the
Device operation or installation is limited to the Device cost.
7. The manufacturer is not responsible for any errors and inaccuracies in guides and
instructions of other companies.
8. The Device requires no maintenance. The Devices case is non-dismountable. In
case of a fault, please refer to Appendix A before contacting the technical support.
9. The manufacturer accepts applications under the warranty and provides technical
support only via e-mail or by the authorized dealers.
10. Contact details of the manufacturer and a list of the authorized dealers are
published on the website: http://www.yachtd.com/.
— 7 —
Product Specification
Figure 1. Combined drawing of the Thermometer and Barometer
— 8 —
Device parameter Value Unit
Operating voltage (from an NMEA 2000 network) 7..16 V
Protection against reverse polarity Yes —
Consumption current of the Thermometer / Barometer 24 / 24 mA
Load Equivalency Number 1 LEN
Operating temperature range (except the Thermometer sensor) -40..+80 °С
Weight of the Thermometer / Barometer 31 / 11 g
NMEA 2000 data output resolution 0.01 °С / hPa
Parameters of the Barometer
Measurement range 300..1100 hPa
Relative measurement accuracy ± 0.12 hPa
Absolute measurement accuracy, at 0..+65 °С± 1 hPa
Absolute measurement accuracy in the rest of the range ± 2.5 hPa
Parameters of the Thermometer
Measurement range -55..+125 °С
Error of the thermometer within the range of -10..+85°C, max ± 0.5 °С
Error of the thermometer within the rest of the range, max ± 2 °С
— 9 —
Device Connection and Testing
The Device requires no maintenance; calibration of the digital sensors has been
performed by the manufacturer.
When deciding where to install the Device, choose a dry mounting location.
Avoid places where the Device can be ooded with water, this can damage it. The
Thermometer sensor has a waterproof case made of stainless steel and is not intended
for permanent location in hostile environments such as sea water. To prevent
corrosion, when installing outdoors protect the sensor case with the help of a coating
of paint.
Read the model number on the Device case. If the model name has the T index at
the end (for example, YDBC-05NT), then the device has a built-in terminator (with
resistance of 120 Ohm) and must be connected to the bus instead of an existing
terminator. Dierent connectors for terminators (blue) and devices (white) are used
in the SeaTalk NG network, which eliminates the chance to err. In networks with the
NMEA 2000 Micro connectors (DeviceNet Micro, Garmin NMEA 2000), devices are
connected to the Female connector on the bus, while terminators are connected to
both Male and Female connectors.
The Device is directly connected to the bus without a drop cable. Before connecting
the Device, turn o the bus power supply. Refer to the manufacturer's documentation
if you have any questions regarding the use of connecting cables, terminators and
connectors:
• SeaTalk NG Reference Manual (81300-1) for Raymarine networks
• Technical Reference for Garmin NMEA 2000 Products (190-00891-00) for
Garmin networks
— 10 —
After connecting the Device, close the lock on the connection to ensure its water
resistance and reliability.
Figure 1. SeaTalk NG bus with the YDBC-05RT, YDTC-13R and
YDBC-05R (left to right)
After turning on the bus power supply, the Device LED will produce short signals
every 2 seconds.
If the Device is connected to a network having a chartplotter or any other device
transmitting a PGN 0x1F814 (129044) message with chart datum conguration or
Other manuals for YDTC-13
1
This manual suits for next models
9
Table of contents
