Xerox WorkCentre M118 Installation and maintenance instructions
XEROX®WORKCENTRE M118 • 128
DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
XEROX®WORKCENTRE M118 DRUM CARTRIDGE
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
1. Remove the two screws located on the handle side end cap. Remove the end cap.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
REMANUFACTURING THE XEROX WORKCENTRE
M118/128 DRUM CARTRIDGE
By the Technical Staff at UniNet
SUPPLIES REQUIRED
1. Xerox WorkCentre M 118/128 developer (used in OPC cartridge)
2. Xerox WorkCentre M 118/128 drum cartridge replacement chip
3. Xerox WorkCentre M 118/128 OPC drum
4. Xerox WorkCentre M 118/128 wiper blade
5. Conductive Grease
TOOLS REQUIRED
1. Phillips head screwdriver
2. Small common screwdriver
3. Vacuum approved for toner
2. Remove the four screws from the inner end cap. Remove the end cap.
3. Follow the wires from the inner end cap to the sensor.
Pry up on the two locking tabs and remove the sensor.
Place a small piece of tape over the sensor hole.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
4. On the non gear side, remove the four screws from the end cap.
Remove the end cap.
5. On the large gear side, remove the metal plate and the drum bushing.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
6. On the opposite side (non gear side) pry off the white gear and the drum bushing.
7. Carefully separate the two halves. 8. Remove the drum and place aside.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
9. Remove the PCR. 10. Remove the two screws from the wiper blade.
Remove the blade.
11. Clean out any toner from the hopper.
Make sure you also clean out the auger post.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
12. Install the new wiper blade and two screws. 13. Clean the PCR with your normal cleaner. Wipe off the old
conductive grease from the shaft and replace. Re-install the
PCR in the assembly grease side to the black PCR holder.
14. Place the drum in the hopper and carefully place aside. 15. On the developer roller side, remove the two springs from
the metal slide cover.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
16. Remove the plastic spring arm, and the two screws.
17. Remove the screw from the contact plate on the opposite
side of the hopper.
18. Carefully pry up the three plastic tabs on the back edge of
the cartridge.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
19. Lift off the cover and locate the chip. 20. From the inside of the cover remove and replace the chip.
21. Remove all the old developer from the hopper. 22. Pour in the new developer.
Make sure you cover both augers.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
23. Snap the cover back in place.
Make sure all three tabs lock!
24. Install the back screw in front of the metal cover.
25. Install the plastic spring arm and the screw to hold it in
place (sliding the cover over allows the spring arm to fit
correctly).
26. On the opposite side, install the screw into the metal
contact.
XEROX WORKCENTRE M118 •128 DRUM CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
Other manuals for WorkCentre M118
2
This manual suits for next models
1
Table of contents
Other Xerox Printer manuals
Xerox
Xerox DocuPrint C2255 User manual
Xerox
Xerox PHASER 6140 Installation and user guide
Xerox
Xerox 6180DN - Phaser Color Laser Printer User manual
Xerox
Xerox B210 Operating manual
Xerox
Xerox WorkCentre M24 Color User manual
Xerox
Xerox 7700 User manual
Xerox
Xerox Phaser 6110 User manual
Xerox
Xerox DocuColor 7000AP Instruction Manual
Xerox
Xerox Phaser 6500 Operating manual
Xerox
Xerox 4850 HighLight Color User manual
Xerox
Xerox 3130 - Phaser B/W Laser Printer User manual
Xerox
Xerox Phaser 7750 Installation and maintenance instructions
Xerox
Xerox Phaser 6300 User manual
Xerox
Xerox Phaser 6022 Operating manual
Xerox
Xerox VersaLink C7000 User manual
Xerox
Xerox ApeosPort C6550 I Service manual
Xerox
Xerox DocuColor 7000 User manual
Xerox
Xerox Phaser 6700 Operating manual
Xerox
Xerox Phaser 8500 User manual
Xerox
Xerox PHASER 7500 User manual
