Wirepath WPS-565-BUL-A User manual
CAMERA
BULLET
INSTALLATION MANUAL
Review manual thoroughly before installation.
Retain for future reference.
WPS-565-BUL-A
2
WPS-565-BUL-A Installation Manual
Safety Instructions
This information is provided to ensure your safety and to prevent
physical or nancial loss. Please read this document carefully before installing and
operating the camera.
1. Handle with care.
Use caution when handling to avoid damage to sensitive internal
components.
2. Do not install camera under extreme temperatures.
This camera only operates under temperature conditions between 14˚F ~
140˚F.
3. Do not mount the camera directly facing bright light sources.
Exposing the camera to strong light over long periods of time will
damage the camera’s sensor.
4. Do not supply voltage other than 12V DC or 24V AC.
This camera regulates power within this range. Higher voltages will
damage the camera’s electronic components.
5. Do not install camera in environments with extreme humidity.
Installing camera in environments with extreme humidity may cause
moisture to condense on the surface of the lens or dome cover,
which can affect picture quality.
WPS-565-BUL-A Installation Manual
3
© 2014 Wirepath Surveillance
Table of Contents
1. Features 5
2. Package Contents 6
3. Wiring Recommendations 7
3.1. Wiring Connections 7
4. Installation Instructions 8
5. Camera Operation Setup 10
5.1. Focus, Zoom and Position 10
5.2. Using the Test Adapter 10
6. OSD SETUP Menu 11
6.1. Default Settings Description 11
6.2. How to Navigate the OSD SETUP Menu 12
6.2.1. OSD Joystick (Test Adapter) 12
6.2.2. How to Save Settings 12
6.3. OSD Menu Structure Outline 13
6.4. OSD MENU SETTINGS 15
6.4.1. LENS Menu 15
6.4.1.1. DC Mode 15
6.4.1.2. MANUAL Mode 15
6.4.2. EXPOSURE Menu 16
6.4.2.1. SHUTTER 16
6.4.2.2. AGC (Auto Gain Control) 16
6.4.2.3. DWDR(Digital Wide Dynamic Range) 16
6.4.3. WHITE BALANCE Menu 17
6.4.3.1. Auto Modes 17
6.4.3.2. AWCSET Mode 17
6.4.3.3. WB MANUAL Setting Mode 17
6.4.4. BACKLIGHT Menu 18
6.4.4.1. BLC (Back Light Compensation) Setup 18
6.4.4.2. HLC (High Light Compensation) Setup 18
6.4.5. DAY & NIGHT Menu 19
6.4.5.1. D&N EXT (External Sensor) 19
6.4.5.2. D&N COLOR Mode 19
6.4.5.3. B/W Setting 19
6.4.5.4. D&N AUTO Setting 19
4
WPS-565-BUL-A Installation Manual
6.4.6. DPC (Dead Pixel Compensation) 20
6.4.7. SPECIAL Menus 21
6.4.7.1. CAM TITLE Setting 21
6.4.7.2. MOTION Detection 21
6.4.7.3. PRIVACY Setting 22
6.4.7.4. PARK LINE Setting 22
6.4.7.5. IMAGE ADJ. Setting 23
6.4.7.6. COMM ADJ. — RS485 Setup 24
6.4.8. Exit Menu — Save and Reset 24
6.4.8.1. SAVE 24
6.4.8.2. NOT SAVE 24
6.4.8.3. RESET 24
7. Troubleshooting 25
8. Specications 26
9. Dimensions 27
10. 5-Year Limited Warranty 27
11. Contacting Technical Support 27
WPS-565-BUL-A Installation Manual
5
© 2014 Wirepath Surveillance
1. Features
1/3” 960H Sony Super-HAD II CCD
The Sony Super HAD II CCD is ideal for low lux illumination, resulting in a clear and
crisp image.
Varifocal Auto-Iris Lens
This camera features a varifocal lens with a focal length of 2.8-12 mm. The auto-
iris function intuitively manages the amount of light passing through the lens for
consistent image brightness.
DWDR (Digital Wide Dynamic Range)
Digital Wide Dynamic Range is ideal for high contrast environments, improving
the contrast between very dark and very bright areas in a scene, and producing
a more balanced image.
2D Digital Noise Reduction
Digital noise reduction produces clear images in low light conditions. Not only
does it help to reduce image noise, but it also minimizes burring of objects
in motion, producing extremely clear picture quality — even under low-light
conditions.
RS-485 Connection and OSD
This camera features an OSD (on-screen display) for initial setup and settings
adjustment. Remote control is possible using a compatible DVR or PTZ controller
connected to the camera’s RS485 wire leads.
Weatherproof Housing
The IP66-rated weatherproof housing makes this camera ideal for outdoor
surveillance.
External Zoom and Focus Adjustments
Adjust the camera without the need to remove the lens cap for quick
adjustments.
Video Test Port
Adjust angle, zoom, and focus at the camera for fast and easy installation.
6
WPS-565-BUL-A Installation Manual
2. Package Contents
(1) WPS-565-BUL-A Camera
(1) WPS-ACC-PWR-M AC/DC Power Plug
(1) OSD Joystick / BNC Test Adapter
(4) Surface Mounting Screws (includes 1 spare)
(4) Wall Anchors (includes 1 spare)
(1) 3mm Allen key
(1) Installation Manual
(1) Spare Silica packet in vacuum sealed bag
NOTE: A POWER SUPPLY IS NOT INCLUDED WITH THIS CAMERA.
The PS-12DC-1A or WPS-PS multiple output power supplies are recommended.
NOTE 2: A SILICA DESICCANT PACK IS MOUNTED INSIDE THE DOME HOUSING.
This package should remain inside the housing after installation, even when
adding additional desiccant packs.
WPS-565-BUL-A Installation Manual
7
© 2014 Wirepath Surveillance
3. Wiring Recommendations
Wiring should be installed, terminated, and tested for connectivity before the
camera is installed. Specications for each connection are detailed below.
3.1. Wiring Connections
12V DC
Power In
BNC
Video Out RS485 Leads
1. Power (Required)
It is recommended to install the camera power supply near the recording
location and run a remote power wire to the camera. Use the included WPS-
ACC-PWR-M to adapt the power wire to the camera.
Use the voltage drop calculator at www.SnapAV.com to nd the correct gauge for a given length of
wire.
Pinout Wire Size (AWG) Power Requirements
+
—
Minimum 18 AWG
Calculate based on
voltage and wire
length
12V DC or 24V AC
(500mA minimum)
Included WPS-ACC-PWR-M is illustrated to demonstrate the correct polarity for power.
2. BNC Video Output (Required)
Install coaxial cable for transmitting video to a DVR or display monitor.
Recommended Cable Connector Type
RG-59 or RG-6 75-ohm rated BNC connectors
Use a BNC-RCA adapter for composite input
3. RS485 Communication +/- Wires (Optional)
Connect the RS485 wires to a controller or a Wirepath DVR for remote access
to the OSD setup menu.
Pinout Wire Size (AWG)
Camera Controller Minimum 24 AWG
2 Cat5e/6 conductors or 2-conductor alarm wire is
recommended
+(White) +(Positive)
-
(Green)
-
(Negative)
Important! Separate and insulate the ends of the RS485 wires if they will not be
connected. DO NOT connect the + and - wires together.
1 2 3
8
WPS-565-BUL-A Installation Manual
4. Installation Instructions
Wiring must be installed before the camera. See the previous page for
connections and wiring recommendations.
Step 1. Prepare for Installation
A. Unpack the camera and locate the included hardware, silica packet, and
3mm Allen wrench. If a mounting accessory is being used, unpack the acces-
sory and become familiar with its installation and use.
B. Depending on the mounting location, it may be easier to position for the cor-
rect eld-of-view before installation. See step 3, “Position the Camera” on the
next page for adjustment instructions.
Step 2. Mount the Camera
Using Mounting Accessories
Mount the accessory according to its instructions, make wiring connections, and
mount the camera. Then, continue these instructions at Step 3 on the next page
to complete camera installation.
Surface Mounting
A. Use the camera mounting base as a template to mark the location of the 3
screws on the mounting surface.
B. Connect the camera to the wiring and move it into position. Avoid pinching
the wires between the camera and the mounting surface.
C. Use 3 of the included screws to secure the camera and hand-tighten them
evenly.
WPS-565-BUL-A Installation Manual
9
© 2014 Wirepath Surveillance
Step 3. Position the Camera
Adjust the camera to point in the proper direction using adjustment points A,
B, and C. Use the 3mm Allen wrench to loosen and tighten each adjustment
screw.
A. Horizontal rotation
B. Swivel left or right
C. Tilt viewing angle
Step 4. Adjust Focus, Zoom, and Menu Settings
See “Camera Operation Setup” beginning on the next page for instructions. Set
the focus and zoom adjustments, and adjust the OSD Setup Menu options as
needed. Disconnect the test adapter after completing adjustments.
Step 5. Close the Camera
Remove the spare silica packet from its sealed foil package (taking care not to
rip the inner packet) and place it inside the test adapter opening.
A
B
C
10
WPS-565-BUL-A Installation Manual
5. Camera Operation Setup
5.1. Focus, Zoom and Position
The lens of the camera has manual focus and zooms knobs for setting the
correct eld of view. Connect the test adapter as described below to use a
monitor at the camera location for viewing adjustments. Use the included 3mm
Allen Wrench to adjust focus and zoom.
5.2. Using the Test Adapter
Connect to the “Test
Adapter” plug above.
Focus
(Front)
Zoom
(Rear) Test Adapter Connector
Connect the yellow BNC
adapter to a video monitor to
view the menu.
Use a BNC-RCA adapter to connect
to a TV’s yellow “Composite” input.
Connect the red power
plug to a 12V DC, 500mA
minimum power supply.
Use the center button to
navigate the OSD menu
structure.
Table of contents
Other Wirepath Security Camera manuals
Wirepath
Wirepath Surveillance WPS-550-BUL-IP User manual
Wirepath
Wirepath WPS-750-BUL-IPH User manual
Wirepath
Wirepath WPS-300-CUB-IP-WH User manual
Wirepath
Wirepath WPS-700-DOM-A-WH User manual
Wirepath
Wirepath WPS-100-BUL-A-SL User manual
Wirepath
Wirepath WPS-365-DOM-A User manual
Wirepath
Wirepath WPS-365-BUL-A User manual
Wirepath
Wirepath WPS-500-BUL-A-WH User manual
Wirepath
Wirepath WPS-500-DOM-A-WH User manual
Wirepath
Wirepath WPS-100-DOM-A-WH User manual
