Whispbar K526 User manual
K526
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 4 x 1 x 1 x 2
x 2 x 1 x 1
Revision No: 2C 1
Fitting Kit K526
MAX kgs (lbs)
W/P WHD
Chevrolet
Lacetti , 5dr Hatch 03-08 EU 40 kgs (88 lbs) 40 kgs (88 lbs)
2
Fitting Kit EN
K526
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K526
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K526
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = 725A
B = 726A
C = 727A
5
Fitting Kit EN
K526
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
6
Fitting Kit EN
K526
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-256
B = 11-04-257
C = 11-04-244
●Fit rubber pads (supplied with fitting kit) to
foot. Pad may vary in shape to that shown.
●Make sure the pad fits into the holes
underneath the foot.
7
Fitting Kit EN
K526
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 5 Nm (3.7 ft lb).
8
Fitting Kit EN
K526
●Tighten locking screw on both legs evenly.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
9
Fitting Kit EN
K526
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Table of contents
Other Whispbar Automobile Accessories manuals
Whispbar
Whispbar K523W User manual
Whispbar
Whispbar K846W User manual
Whispbar
Whispbar K174W User manual
Whispbar
Whispbar K450W User manual
Whispbar
Whispbar K856W User manual
Whispbar
Whispbar K360W User manual
Whispbar
Whispbar K484W User manual
Whispbar
Whispbar K948W User manual
Whispbar
Whispbar K973W User manual
Whispbar
Whispbar K335W User manual
Whispbar
Whispbar K762W User manual
Whispbar
Whispbar K820W User manual
Whispbar
Whispbar K092W User manual
Whispbar
Whispbar K822 User manual
Whispbar
Whispbar K944W User manual
Whispbar
Whispbar K937W User manual
Whispbar
Whispbar K194W User manual
Whispbar
Whispbar K930 User manual
Whispbar
Whispbar K541W User manual
Whispbar
Whispbar K850W User manual
