Whispbar K758W User manual
K758W
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 2 x 2 x 4 x 4
x 1 x 4
Revision No: 1A 1
Fitting Kit K758W
MAX kgs (lbs)
W/P WHD
BMW
1 Series F21, 3dr Hatch 12-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
1 Series F21, 3dr Hatch 12-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
1 Series F20, 5dr Hatch 12-+ NZ 75 kgs (165 lbs) 75 kgs (165 lbs)
1 Series F20, 5dr Hatch 12-+ AU 75 kgs (165 lbs) 75 kgs (165 lbs)
1 Series F20, 5dr Hatch 12-+ EU 75 kgs (165 lbs) 75 kgs (165 lbs)
1 Series F20, 5dr Hatch 12-+ ZA 75 kgs (165 lbs) 75 kgs (165 lbs)
1 Series F20, 5dr Hatch 12-+ CN 75 kgs (165 lbs) 75 kgs (165 lbs)
2
Fitting Kit EN
K758W
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
●This kit fits type A, B, C and D.
●Use keys to remove covers.
3
Fitting Kit EN
K758W
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
●Attaches to factory-fitted mounting points
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Adjust crossbar in or out to suit vehicle.
Refer to the crossbar instructions for
crossbar adjustment.
4
Fitting Kit EN
K758W
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
●Remove plastic clamp block by gripping bar
leg with fingers and push firmly with
thumbs until clamp block drops out behind
leg.
●Select plastic internal block (from fitting kit)
and insert into foot.
●Repeat for all legs.
5
Fitting Kit EN
K758W
Fitment
●Open or remove fixed-point covers.
●Select grubscrews and screw into the
vehicle's fixed points.
●Do not over tighten.
●Repeat for all four positions.
●Refer to the underside of the pad for the
part number.
6
Fitting Kit EN
K758W
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 11-04-224
B = 11-04-225
●Ensure the fixed-point covers sit vertically
in the recess in the pads.
●Place crossbars on pads ensuring the pads
fit into the holes underneath the foot and
the grubscrew passes through the hole in
the foot.
●Repeat for all four positions.
●Tighten adjusting screw to 5 Nm (3.7 ft lb)
hand tight.
7
Fitting Kit EN
K758W
●Place wingnut over grubscrew and tighten
down.
●Repeat for all legs.
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
8
Fitting Kit EN
K758W
Maintenance
●Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
●Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
●Set crossbars a minimum distance of
700mm (27 1/2") apart where no other
distance is specified in the fitting
instructions. This is especially important
when carrying long loads.
●Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
●Some glass/panoramic roofs and radio
antennae may not be able to be used when
the product is fitted.
●Do not modify this product.
●Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the
fitting instructions.
●Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
●Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
●Objects with pointed ends (e.g. ski poles)
should be carried with the pointed ends to
the rear of the vehicle.
●Remove all loose or removable objects
from the load prior to loading.
●Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
●A loaded roof rack system can alter the
performance of your vehicle. Be especially
aware of the effects of side winds,
changing of direction, and braking
performance. Avoid rapid acceleration and
deceleration. Drive carefully.
●Note that the total height of the vehicle
increases when upright loads are carried.
●Products should be locked during transport
if they have locks fitted.
9
Fitting Kit EN
K758W
●Check and replace worn out or defective
parts.
●Keep the product clean and maintained.
●Never drive into a car wash with the roof
rack system fitted.
●Lubricate locks and adjusting screws at
regular intervals.
●Remove the products from the vehicle
when not in use. Make sure all loose parts
are stored safely.
●Yakima Products, Inc.
Archimedesbaan 25
3439 ME Nieuwegein
The Netherlands
+31 (0)30 600 1070
www.whispbar.eu
www.whispbar.co.uk
●Yakima Products, Inc.
15025 SW Koll Pkwy.
Beaverton, OR 97006-6056
USA
www.whispbar.com
www.whispbar.ca
10
Table of contents
Other Whispbar Automobile Accessories manuals
Whispbar
Whispbar K439W User manual
Whispbar
Whispbar K088W User manual
Whispbar
Whispbar K109W Operation and installation manual
Whispbar
Whispbar K491W User manual
Whispbar
Whispbar K340W Operation and installation manual
Whispbar
Whispbar K417W Operation and installation manual
Whispbar
Whispbar K868W User manual
Whispbar
Whispbar K541 Operation and installation manual
Whispbar
Whispbar K145W Operation and installation manual
Whispbar
Whispbar K429W User manual
Whispbar
Whispbar K157W User manual
Whispbar
Whispbar K951W Operation and installation manual
Whispbar
Whispbar K867W User manual
Whispbar
Whispbar K774W User manual
Whispbar
Whispbar K797W User manual
Whispbar
Whispbar K538W User manual
Whispbar
Whispbar K089W User manual
Whispbar
Whispbar K382W User manual
Whispbar
Whispbar K174W User manual
Whispbar
Whispbar S43W User manual
