Whirlpool CAE2743BQ User manual

Whir I

COMMERCIAL

LAUNDRY

®INSTALLATION

INSTRUCTIONS

COMMERCIAL WASHER

MODELS

CAE2743BQ

CAE2763BQ

CAE2793BQ

QCAE2733BQ

INSTRUCTIONS

D'INSTALLATION

LAVEUSECOMMERCIALE

TABLE OF CONTENTS Page

Washer Safety .......................................................................... 2

Tools & Parts ............................................................................ 3

Dimensions .............................................................................. 4

Location Requirements ........................................................... 5

Drain System ............................................................................ 6

Electrical Requirements .......................................................... 7

Installation instructions .......................................................... 8

Connect Drain Hose ................................................................ 9

Connect Inlet Hoses .............................................................. 10

Level Washer .......................................................................... 11

InstaRing Coin Slide and Coin Box ....................................... 11

Complete InstaRation ............................................................ 12

Typical Full Load Sizes .......................................................... 12

Washer Maintenance ............................................................. 13

If You Need Assistance ......................................................... 14

Alternate Parts ....................................................................... 14

TABLE DES MATIERES Page

S6curit_ de la laveuse ........................................................... 15

Outillage et pi_ces ................................................................. 16

Dimensions ............................................................................ 17

Exigences d'emplacement ................................................... 18

Syst_me de vidange .............................................................. 19

Sp6cifications 61ectriques .................................................... 20

instructions d'installation ..................................................... 21

Raccordement du tuyau de vidange .................................... 22

Raccordement des tuyaux d'arriv6e d'eau ......................... 23

15tablissement de I'aplomb de la laveuse ............................ 24

InstNlation de la glissi_re et de la bore h monnaie ........... 24

Achever I'installation ............................................................. 25

Taille typique des charges completes ................................. 25

Entretien de la laveuse .......................................................... 26

Si vous avez besoin d'assistance ........................................ 27

Autres pi_ces ......................................................................... 27

W10474263C

W10474279B = SP www.whirlpoolcomrnerciallaundry.com

WASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions,

including the following:

[] Read all instructions before using the washer.

[] Do not wash articles that have been previously cleaned

in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, other flammable, or explosive

substances as they give off vapors that could ignite or

explode.

[] Do not add gasoline, dry-cleaning solvents, or other

flammable, or explosive substances to the wash water.

These substances give off vapors that could ignite or

explode.

[] Under certain conditions, hydrogen gas may be

produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. if the hot water system has not been

used for such a period, before using the washing

machine, turn on all hot water faucets and let the water

flow from each for several minutes. This will release

any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during

[] Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used

near children.

[] Before the washer is removed from service or discarded,

remove the door or lid.

[] Do not reach into the washer if the drum, tub or agitator is

moving.

[] Do not install or store the washer where it will be exposed to

the weather.

[] Do not tamper with controls.

[] Do not repair or replace any part of the washer or attempt any

servicing unless specifically recommended in this manual or in

published user=repair instructionsthat you understand and

have the skills to carry out.

[] See "Electrical Requirements" located in the installation

instructions for grounding instructions.

this time. SAVE THESE iNSTRUCTiONS

FOR YOUR SAFETY i

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

Tools Needed:

TOOLS &PARTS

LeveJ Pliers Utility Knife

Adjustable Wrench

Optional tools:

Flat=Blade Screwdriver

Parts Supplied:

Water Inlet Hoses (2)

Inlet Hose Washers (4) Drain hose with clamp,

U=form, and cable tie

DIMENSIONS

Front View

[

411/4"

(1.047 m)

1" --D

(25 ram)

27"

(686 ram)

-(5211/2"

46 ram)

.,,i- 25/8'' 5/8,,

(67 ram) (16 ram)

NOTE: Service panel not included on some models.

35"

(889 ram)

(25 ram)

Side View

271/2"

-,t----- (699 mm)_ INon=coin=operated

27" "=---_ I models:

(686 ram) _ 61/4,,

¢,--V (159 mm)

,' ' Coin-operated

............................_................ ' models:

q 81/4,,

(210 ram)

Back View

431/4''

(1.o98m)

36"

(914 ram)

61/2 H

(165 ram)

(25 ram'

41/4,,

(108 ram)

27"

(686

51/2 H

40 mm)

411/4"

(1.047 m)

351/2''

(902 ram)

LOCATION REQUIREMENTS

Selecting the proper location for your washer improves

performance and minimizes noise and possible washer "walk."

Your washer can be installed in a basement, laundry room, or

recessed area. See "Drain System."

Companion appliance location requirements should also be

considered.

IMPORTANT." Do not install or store the washer where it will be

exposed to the weather. Do not store or operate the washer in

temperatures at or below 32°F (0°C). Some water can remain in

the washer and can cause damage in low temperatures. Proper

installation is your responsibility.

You will need:

[] A water heater set to 120°F (49°C).

[] A grounded electrical outlet located within 4 ft. (1.2 m) of

power cord on back of washer. See "Electrical Requirements."

[] Hot and cold water faucets located within 4 ft. (1.2 m) of hot

and cold water fill valves on washer, and water pressure

of 20-100 psi (138-690 kPa). A pressure reduction valve

should be used in the supply line where inlet pressure

entering the building exceeds 100 PSi (690 kPa) to avoid

damage to the washer mixing valve.

[] Single washer installations require 12" (300 mm) minimum

risers to provide an air cushion and avoid noise and damage

to valves.

[] A level floor with maximum slope of 1" (25 mm) under entire

washer. Installing on carpet is not recommended.

[] Floor must support washer's total weight (with water and load)

of 315 Ibs (143 kgs).

[] A floor drain under the bulkhead. Prefabricated bulkheads

with electrical outlets, water inlet lines, and drain facilities

should be used only where local codes permit.

Recessed Area or Closet Installation

This washer may be installed in a recessed area or closet.

The installation dimensions shown are the minimum spaces

allowable. Additional spacing should be considered for ease of

installation and servicing. If closet door is installed, the minimum

air openings in top and bottom of door are required. Louvered

doors with air openings in top and bottom are acceptable.

Companion appliance spacing should be considered.

Minimum installation spacing

14" max, _! .....

(356 ram)_.

(127ram)I_--....

(25 ram}

ram)

(25 ram)

(761

(75=

)cm_)l

DRAIN SYSTEM

Drain system can be installed using a floor drain, wall standpipe,

floor standpipe, or laundry tub. Select method you need.

Floor standpipe drain system

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum

carry-away capacity: 10 gal. (38 L) per minute. Top of standpipe

must be at least 39" (990 mm) high; install no higher than

96" (2.44 m) from bottom of washer.

Floor drain system

(

Floor drain system requires a Siphon Break Kit (Part Number

285834). Minimum siphon break: 28" (710 mm) from bottom

of washer. Additional hoses may be needed.

Laundry tub drain system

Wall standpipe drain system

Minimum capacity: 20 gal. (76 L). The top of the laundry tub

must be at least 39" (990 mm) above floor.

See requirements for floor standpipe drain system.

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into agrounded 3prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

[] A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply

is required. A time-delay fuse or circuit breaker is recommended.

It is recommended that aseparate circuit breaker serving only

this appliance be provided.

[] This washer is equipped with a power supply cord having

a 3 prong grounding plug.

[] To minimize possible shock hazard, the cord must be plugged

into a mating, 3 prong, grounding-type outlet, grounded in

accordance with local codes and ordinances. If a mating outlet

is not available, it is the personal responsibility and obligation

of the customer to have the properly grounded outlet installed

by a qualified electrician.

[] If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that

the ground path is adequate.

[] Do not ground to a gas pipe.

[] Check with a qualified electrician if you are not sure the

washer is properly grounded.

[] Do not have a fuse in the neutral or ground circuit.

GROUNDING INSTRUCTIONS

For a grounded, cord=connected washer:

This washer must be grounded. In the event of a malfunction

or breakdown, grounding will reduce the risk of electrical

shock by providing a path of least resistance for electric

current. This washer is equipped with a cord having an

equipment-grounding conductor and a grounding plug.

The plug must be plugged into an appropriate outlet that is

properly installed and grounded in accordance with all local

codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock.

Check with a qualified electrician or serviceman if you are

in doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance - if it will

not fit the outlet, have a proper outlet installed by a qualified

electrician.

For a permanently connected washer:

This washer must be connected to a grounded metal,

permanent wiring system, or an equipment grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead

on the appliance.

INSTALLATION INSTRUCTIONS

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

It is necessary to remove all shipping materials for proper

operation and to avoid excessive noise from washer.

1. Move washer to within 4 ft (1.2 m) of its final location; it must

be in a fully upright position.

NOTE: To avoid floor damage, set washer onto cardboard

before moving it and make sure lid is taped shut.

2. To avoid damaging floor, place cardboard supports from

shipping carton on floor behind washer. Tip washer back and

place on cardboard supports. Remove shipping base. Set

washer upright.

iMPORTANT: Removing shipping base is necessary for proper

operation. Ifyour washer includes a sound shield, please refer

to the instructions included with the sound shield to install it

at this time.

3. Remove tape from washer lid, open lid, and remove cardboard

packing tray from tub. Be sure to remove all parts from tray.

NOTE: Keep tray in case you need to move washer later.

CONNECT DRAIN HOSE

Proper routing of the drain hose avoids damage to your floor

due to water leakage.

Remove drain hose from the washer drum

1. Remove tape from the washer drain port on the back of

the washer.

2. If clamp is not already in place on elbow end of drain hose,

slide it over end as shown.

3. Squeeze clamp with pliers and slide elbow end of drain

hose onto washer drain port and secure with clamp.

4. The washer drain system can be installed using a floor drain,

wall standpipe, floor standpipe, or laundry tub.

5. Place hose into standpipe (shown in picture) or over side

of laundry tub.

IMPORTANT: 4.5" (114 mm) of drain hose should be inside

standpipe; do not force excess hose into standpipe or lay

on bottom of laundry tub. Drain hose form must be used.

Drain

hose form

6. For floor drain installations, you will need to remove the drain

hose form from the end of the drain hose. You may need

additional parts with separate directions. See "Tools and Parts."

7. The floor drain system requires a siphon break that may be

purchased separately. The siphon break (Part Number 285834)

must be a minimum of 28" (710 mm) from the bottom of the

washer. Additional hoses might be needed.

CONNECT INLET HOSES

Insert new hose washers (supplied) into each end of the inlet

hoses. Firmly seat the washers in the couplings.

Washer Coupling

Connect Inlet Hoses to Water Faucets

1. Attach hose to hot water faucet. Screw on coupling until it is

seated on washer. Repeat process for cold water.

(

Connect (nlet Hoses to Washer

1. Attach cold water hose to cold water inlet valve marked with a

blue ring. Screw coupling by hand until it is snug.

2. Attach hot water hose to hot water inlet valve marked with a

red ring. Screw coupling by hand until it is snug.

3. Use pliers to tighten couplings an additional two-thirds turn.

2. Use pliers to tighten the couplings an additional two-thirds

turn.

NOTE: Do not overtighten. Damage to the valve can result.

4. Turn on water faucets to check for leaks. A small amount

of water may enter washer. It will drain later.

iMPORTANT: Do not overtighten or use tape or sealants on valve

when attaching to faucets or washer. Damage can result.

Clear Water Lines

[] Run water through both faucets and inlet hoses, into a laundry

tub, drainpipe, or bucket, to get rid of particles in the water

lines that might clog the inlet valve screens.

[] Check the temperature of the water to make sure that the hot

water hose is connected to the hot water faucet and that the

cold water hose is connected to the cold water faucet.

NOTE: Replace inlet hoses after 5 years of use to reduce the

risk of hose failure. Record hose installation or replacement

dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts,

wear, or leaks are found.

This manual suits for next models

Table of contents

Languages:

Other Whirlpool Washer manuals

Whirlpool

Whirlpool AWSE7000 User manual

Whirlpool

Whirlpool LPR4231A User manual

Whirlpool

Whirlpool 8315954 User manual

Whirlpool

Whirlpool Cabrio WTW6400SW2 User manual

Whirlpool

Whirlpool LOAD-SENSING W10330946A User manual

Whirlpool

Whirlpool TOP-LOADING WASHER User manual

Whirlpool

Whirlpool WWDC 8220/1 User manual

Whirlpool

Whirlpool LA5300XM User manual

Whirlpool

Whirlpool LLV8245BW0 User manual

Whirlpool

Whirlpool 3950319 User manual

Whirlpool

Whirlpool WFW9150WW User manual

Whirlpool

Whirlpool LMR4131A User manual

Whirlpool

Whirlpool GHW9400PL User manual

Whirlpool

Whirlpool W11556538A-SP User manual

Whirlpool

Whirlpool LHB 802 User manual

Whirlpool

Whirlpool WWDC 7410 User manual

Whirlpool

Whirlpool Cabrio,- WED7300X User manual

Whirlpool

Whirlpool FSCR70212 Installation and operation manual

Whirlpool

Whirlpool W10275729D User manual

Whirlpool

Whirlpool WFW94HEXW Parts list manual

Whirlpool

Whirlpool WTW5600XW Assembly instructions

Whirlpool

Whirlpool 3360620 User manual

Whirlpool

Whirlpool AWO/D 43115 User manual

Whirlpool

Whirlpool Duet Steam User manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Beko

Beko WKB 51231 PTMA manual