Whirlpool 8315954 User manual

Installation Instructions

I PORTANT:

Read and save

these instructions

I PORTANT:

Installer: eave Installation Instructions

with the owner.

Owner: Keep Installation Instructions for

future reference.

Save Installation Instructions for local

electrical inspector’s use.

CO ERCIAL

WASHER

120-volt, 60-Hz odels

Part No. 8315954B

COMMERCIA

AUNDRY

PRODUCTS

www.whirlpool.com

8315954 Rev B ENv06:YC10665/8315954A 5/3/10 11:04 AM Page 1

PAGE 2

Before you start...

We have provided many important

afety me age in thi manual and

on your appliance. Alway read

and obey all afety me age .

WARNING

Thi i the afety alert ymbol.

Thi ymbol alert you to

potential hazard that can kill or

hurt you and other .

All afety me age will be preceded

by the afety alert ymbol and the

word “DANGER” or “WARNING”.

The e word mean:

All afety me age will tell you

what the potential hazard i , tell you

how to reduce the chance of injury,

and tell you what can happen if the

in truction are not followed.

You can be killed or seriously

in ured if you donʼt immediately

follow instructions.

You can be killed or seriously

in ured if you donʼt follow

instructions.

DANGER

Your safety and the safety of others are very important.

I PORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons

when using your washer, follow basic precautions, including the following:

SAVE THESE INSTRUCTIONS

•Read all instructions before using

the washer.

• Do not wash articles that have

been previously cleaned in,

washed in, soaked in, or spotted

with gasoline, dry-cleaning

solvents, other flammable or

explosive substances as they give

off vapors that could ignite or

explode.

• Do not add gasoline, dry-cleaning

solvents, or other flammable or

explosive substances to the wash

water. These substances give off

vapors that could ignite or

explode.

• Under certain conditions,

hydrogen gas may be produced in

a hot water system that has not

been used for 2 weeks or more.

HYDROGEN GAS IS EXP OSIVE. If

the hot water system has not been

used for such a period, before

using a washing machine, turn on

all hot water faucets and let the

water flow from each for several

minutes. This will release any

accumulated hydrogen gas. As

the gas is flammable, do not

smoke or use an open flame

during this time.

• Do not allow children to play on or

in the washer. Close supervision of

children is neceassary when the

washer is used near children.

• Before the washer is removed from

service or discarded, remove the

lid.

• Do not reach into the washer if the

tub or agitator is moving.

• Do not install or store this washer

where it will be exposed to the

weather.

• Do not tamper with controls.

• Do not repair or replace any part

of the washer or attempt any

servicing unless specifically

recommended in the Owner's

Manual or in published user-repair

instructions that you understand

and have the skills to carry out.

• See Installation Instructions for

grounding requirements.

8315954 Rev B ENv06:YC10665/8315954A 5/3/10 11:04 AM Page 2

Check location where washer will be

installed. Proper installation is your

responsibility. Make sure you have

everything necessary for correct

installation.

Do Not store or operate washer below

32°F (0°C) (some water may remain in

washer).

Hot and cold water faucets: Must be

within 4 feet (1.2 meters) of the back

of the washer and provide water

pressure 10 - 100 PSI (69-690 kPa). A

pressure reduction valve should be

used in the supply line where inlet

pressure entering the building

exceeds 100 PSI (690 kPa) to avoid

damage to the washer mixing valve.

Grounded

electrical outlet

is required. See

Electrical

requirements.

Single washer

installations require

12-inch (300 mm)

minimum risers to

provide an air

cushion and avoid

noise and damage

to valves.

Untape and

open washer

lid. Remove

packages and

hoses from

washer.

Water heater: Set to

deliver 120°F (49°C)

water to the washer.

Standpipe drain system: Needs a

two-inch (50 mm) minimum carry-

away capacity of 17 gallons (64.4

liters) per minute. Top of standpipe

must be at least 39 inches (990 mm)

high and no higher than 72 inches

(1.83 m) from bottom of washer.

Level floor: Maximum slope

under washer — 1 inch (25 mm).

Front access to the pump area is

available by removing 2 No. T20

Torx®† screws and then removing

the front panel.

I PORTANT: Floor must be sturdy

enough to support loaded washer

weight of 315 pounds (143 Kg).

A floor drain should be

provided under the bulkhead.

Prefabricated bulkheads with

electrical outlets, water supply

lines and drain facilities should

be used only where local

codes permit.

I PORTANT: Observe all governing

codes and ordinances.

PAGE 3

No. T20 TORX®†

screws

†® TORX is a registered trademark of Acument

Intellectual Properties, C.

8315954 Rev B ENv06:YC10665/8315954A 5/3/10 11:04 AM Page 3

PAGE 4

Tools needed for

installation:

Level Pliers

Utility

knife

Wrench

Scissors

Flat-blade

screwdriver

Electrical requirements

Grounding

prong

Figure 1

3-prong grounding-

type outlet

3-prong

grounding

plug

Power

supply cord

Plug into a grounded 3-prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions

can result in death, fire, or electrical

shock.

Electrical Shock Hazard

Parts supplied for

installation:

Remove parts from packages. Check

that all parts were included.

1 hose clamp

2 inlet hoses

4 flat water hose washers

2 front-leveling legs with nuts

1 drain hose

Recommended

grounding method

For your personal safety, this appliance

must be grounded. This appliance is

equipped with a power supply cord

having 3-prong grounding plug. To

minimize possible shock hazard, the cord

must be plugged into a mating 3-prong

grounding-type outlet, grounded in

accordance with local codes and

ordinances. See Figure 1. If a mating

outlet is not available, it is the personal

responsibility and obligation of the

customer to have a properly grounded

3-prong outlet installed by a qualified

electrician.

WARNING – Improper connection of the

equipment-grounding conductor can

result in a risk of electric shock. Check with

a qualified electrician or serviceman if you

are in doubt as to whether the appliance is

properly grounded. Do not modify the plug

provided with the appliance – if it will not fit

the outlet, have a proper outlet installed by

a qualified electrician.

WARNING

*0" *0"

Front view

(door not shown

Side view

Minimum installation spacing

Recessed area

instructions

This washer may be installed in a

recessed area or closet.

The installation dimensions shown are

the minimum spaces allowable.

Additional spacing should be

considered for ease of installation

and servicing. If closet door is

installed, the minimum air openings in

top and bottom of door are required.

ouvered doors with air openings in

top and bottom are acceptable.

Companion appliance spacing

should be considered.

Closet door

Front view Closet door

17"

(430 mm)

14"

(350 mm)

max.

(100 mm)

min.

1" (25 mm)

min.

(76 mm)

24 sq. in.

(1.55 sq. m)

24 sq. in.

(1.55 sq. m)

48 sq. in.

(3.10 sq. m)

48 sq. in.

(3.10 sq. m)

If codes permit and a separate ground wire

is used, it is recommended that a qualified

electrician determine that the ground path

is adequate.

Do Not ground to a gas pipe.

Check with a qualified electrician if you are

not sure the washer is properly grounded.

Do Not have a fuse in the neutral or ground

circuit.

A 120-volt, 60-Hz, AC-only, 15- or

20-ampere fused electrical supply is

required. (Time-delay fuse or circuit breaker

is recommended.) It is recommended that

a separate circuit serving only this

appliance be provided.

8315954 Rev B ENv06:YC10665/8315954A 5/3/10 11:04 AM Page 4

Use new hoses and washers that came

with your Whirlpool washer.

Replace inlet hoses after 5 years of use

to reduce the risk of hose failure.

Inspect and replace inlet hoses if

bulges, kinks, cuts, wear, or leaks are

found. When replacing your inlet hoses,

mark the date of replacement on the

label with a permanent marker.

2.Insert a flat washer into each end

of the inlet hoses. Check that washers

are firmly seated in couplings.

Coupling

3.Attach hose to bottom inlet

valve opening first. Then second hose

to top inlet. Tighten couplings by

hand; then use pliers to make an

additional two-thirds turn.

7.Before

attaching water

inlet hoses, run

water through

both faucets into

a bucket. This will

get rid of particles

in water lines that

might clog hoses.

Mark which is the hot water faucet.

8.Attach bottom hose (inlet

marked “H”) to hot water faucet.

Attach top hose (inlet marked “C”) to

cold water faucet. Tighten coupling

to faucet by hand; then use pliers to

make final two-thirds turn.

PAGE 5

Inlets are plastic.

Do Not strip or

crossthread.

Hot water

inlet valve

Cold

water

inlet

valve

Washer

4.Move washer close to final

position. Put “hook” end of drain hose

into standpipe. Estimate length of

drain hose needed when washer is in

final position. Hose must be cut

exactly to length so “hook” end is

held tightly over edge of standpipe. If

drain hose is too long, cut straight end

of hose. (Do Not cut “hook” shaped

end of drain hose.)

DO NOT FORCE EXCESS LENGTH OF

DRAIN HOSE DOWN THE STANDPIPE.

THIS COULD CAUSE SIPHONING. See

Step 6.

5.Place hose clamp over washer

drain connector. Push drain hose onto

washer connector. Use pliers to open

clamp and slide clamp over drain

hose. Check for good fit.

6.Measure and mark a point

approximately 16 inches (406 mm)

from the plug end of the shipping

strap. Cut this shipping strap at this

point.

Check that hose is not

twisted or kinked and is

securely in place.

Put “hook” end of drain

hose into standpipe.

Tightly wrap the shipping

strap around the

standpipe. Push plug into

the nearest hole in the

shipping strap.

Now start...

With washer in laundry area.

Pull firmly to remove the end of

shipping strap from the back of the

washer. The shipping strap plug must

be completely removed from the

washer for the self-leveling legs to

be released.

Save the shipping strap for use in

Step 6.

Excessive Weight Hazard

Use two or more people to move

and install washer.

Failure to do so can result in back

or other in ury.

WARNING

9.Stack two corner posts on top of

each other. Tilt washer backwards and

insert corner posts 3 inches (76 mm)

in from one side of washer as shown.

Repeat with other corner posts on other

side of washer.

Shipping

tape

Pull the strap completely

out of the washer.

1. Remove tape that covers

shipping strap. Pull to completely

remove the shipping strap with 2

cotterpins from the inside of the

washer.

16"

(406 mm)

8315954 Rev B ENv06:YC10665/8315954A 5/3/10 11:04 AM Page 5

PAGE 6

1/2"

(13 mm)

Base

Nut

10.Use legs and nuts from parts

package. Screw nut down to within

1/2 inch (13 mm) of

base.

11.

Insert legs into correct

holes at each front corner

of washer until nuts touch washer.

Do Not tighten nuts until Step 14.

13.Tilt washer forward raising

back legs 1 inch (25 mm) off of floor.

To adjust rear self-leveling legs, gently

lower washer to floor. Check levelness

of the washer by placing a

carpenter’s level on top of the

washer, first side to side; then front to

back.

14.If washer is not level, adjust

the front legs up or down. Make final

check with level.

When washer is level, use wrench

to turn nuts on front legs up tightly

against washer base. If nuts are not

tight against washer base, the washer

may vibrate.

20.Check that you have all of

your tools. Check that the shipping

strap was removed from the back of

the washer and used to secure the

drain hose.

If entire strap is not removed, washer

may vibrate and be noisy.

21.Plug power supply cord into

grounded outlet.

18.Check that all parts are now

installed. See parts list, Page 3. If there

is an extra part, go back through

steps to see which step was skipped.

19.Turn on water faucets and

check for leaks. Tighten couplings if

there is leaking. Do Not overtighten;

this could cause damage to faucets.

12.Tilt washer backward and

remove corner posts. Gently lower

washer to floor.

ove washer to its permanent

location. Remove cardboard or

hardboard from under washer.

17.CHECK ELECTRICAL

REQUIRE ENTS. BE SURE YOU HAVE

CORRECT ELECTRICAL SUPPLY AND

RECO ENDED GROUNDING

ETHOD.

15.Remove the service door of

the meter case. ift the service door

up at the back and remove. Install

money accepting device (refer to

manufacturers instructions for proper

installation). For washers using coin

slides, use adapter kit (provided with

washer). Replace meter case service

door.

16.Install added security device.

• Ensure power is not supplied to the

washer.

• Open and remove the service

door.

• ay the security cone small side

down over the oblong hole in the

bottom rear of the meter case

assembly.

• Pass the security bolt through this

cone and thread it by hand into

the cage nut below the oblong

opening.

• Tighten the security bolt by hand a

few turns before using a wrench to

tighten until snug.

NOTE: Installing the security bolt

provides added security, but will add

to the service time when the top needs

to be removed for servicing the

washer.

Security

Cone

Security

Bolt

Cage

Nut

8315954 Rev B ENv06:YC10665/8315954A 5/3/10 11:04 AM Page 6

Check list for washer

operation

Check the following if the washer is

not operating properly:

1. Power supply cord is plugged in.

2. Circuit breaker is not tripped or fuse

blown.

3. Timer has been advanced to start

of a cycle.

4. Water faucets are turned on.

5. Inlet and drain hoses are not

kinked.

6. Washer lid is closed.

7. Inlet valve is frozen if not sheltered

from the weather.

8. Suds level. Excess suds will slow the

spin and cause poor rinsing.

Operate the washer through a

complete cycle with no detergent.

Use less detergent or a controlled

suds type detergent in future loads.

PAGE 7

Additional features

Disconnect power before making

electrical connections.

Failure to do so can result in death

or electrical shock.

Electrical Shock Hazard

WARNING

For WAR RINSE where applicable:

• Remove screws from each end of

the console bottom.

• Pull the console bottom forward;

lift and tilt back.

• Connect J1 to J2

To SAVE WATER where applicable:

• ocate water level switch on

back of washer. (See Back Page.)

• Turn shaft 45° counterclockwise.

If you need

assistance…

The Whirlpool®Commercial aundry

Trade Partner Support Center will

answer any questions about

operating or maintaining your washer

not covered in the Installation

Instructions. The Whirlpool®

Commercial aundry Trade Partner

Support Center is available by dialing

1-800 NO BE TS (1-800-662-3587) —

the call is free.

When you call, you will need the

washer model number and serial

number. Both numbers can be found

on the serial-rating plate located on

your appliance.

22.For electro/mechnical

models only. Check the wash cycle

time. The washer has a 9-minute wash

in the Normal Cycle. Remove the

timer from the meter case of the

washer to manually start the timer.

Start the washer and allow it to

complete the Normal cycle.

Timers can be started by turning the

clutch assembly counterclockwise

until the washer starts to fill with water.

23.If the washer fails to start or

does not give the proper washer

cycle time, the clutch assembly of the

timer can be adjusted. Remove the

timer from the meter case. Adjust the

clutch assembly screw clockwise if

the washer does not start after the

coin slide mechanism has been fully

actuated in or out. Adjust the clutch

assembly counterclockwise if the

washer segment of the Normal cycle

was less than 9 minutes.

Timer-front view

Rotate

counterclockwise

only. Timer "off" position

Timer clutch

adjustment screw

8315954 Rev B ENv06:YC10665/8315954A 5/3/10 11:04 AM Page 7

PAGE 8

Typical full load sizes

Load Loading Load Loading

Type Suggestion Type Suggestion

Mixed 3 double sheets Heavy 3 pair pants

oad 4 pillowcases work 3 shirts

6 pair shorts clothes 1 coverall

8 T-shirts 4 pair jeans

2 shirts 1 overall

2 blouses

8 handkerchiefs

Permanent 2 double or Knits 3 blouses

Press 1 king size sheet 4 slacks

1 tablecloth 6 shirts

1 dress 4 tops

1 blouse 4 dresses

2 slacks

3 shirts

2 pillowcases

It is recommended that fiberglass

items not be washed in coin-

operated washers. If these items are

washed in the washer, run the washer

through a complete cycle to rinse

any residue away that might be left in

the washer.

Moving the washer to

a new location...

Wedge blanket

between tub ring

and cabinet top.

Remove front legs.

Tape 2

sides.

Tape rear

legs in “up”

position.

Note: Do Not

place blanket

in this area

(switch).

• Remove the front legs from the

base of the washer.

• Place both rear leveling legs in the

upper position and tape securely.

• Apply tape to the side and bottom

of the cabinet near the rear.

• Open washer lid, wedge a blanket

between the tub ring and the

cabinet top restricting the tub

movement.

• Handle washer gently. Do Not drop

washer while using hand truck.

Operating Tips

Fire Hazard

Never place items in the washer

that are dampened with gasoline or

other flammable fluids.

No washer can completely remove

oil.

Do not dry anything that has ever

had any type of oil on it (including

cooking oils).

Doing so can result in death,

explosion, or fire.

WARNING

8315954 Rev B ENv06:YC10665/8315954A 5/3/10 11:04 AM Page 8

Power supply cord

11⁄2"

(40 mm)

Cold

Hot

251⁄2"

(650 mm)

Drain hose

connector

(180 mm)

43"

(1.09 m)

(25 mm)

381⁄8"

(970 mm)

51⁄4"

(133 mm)

35"

(890 mm)

27"

(685 mm)

273⁄4"

(705 mm)

Water

inlets

(127 mm)

(180 mm)

Label

Water level

switch and

shaft

PAGE 9

8315954 Rev B ENv06:YC10665/8315954A 5/3/10 11:04 AM Page 9

3/10

Part No. 8315954B

04/10

Printed in U.S.A.

Prepared by Whirlpool Corporation

Benton Harbor, Michigan 49022

® Registered Trademark/TM Trademark of Whirlpool, U.S.A., Whirlpool Canada P icensee in Canada

8315954 Rev B ENv06:YC10665/8315954A 5/3/10 11:04 AM Page 10

Other manuals for 8315954

Table of contents

Languages:

Other Whirlpool Washer manuals

Whirlpool

Whirlpool LBR5432PT2 User manual

Whirlpool

Whirlpool WTW500CMW User manual

Whirlpool

Whirlpool WFW6620HW User manual

Whirlpool

Whirlpool WFW5605MW User manual

Whirlpool

Whirlpool WHP1000S User manual

Whirlpool

Whirlpool WFE 1480DW User manual

Whirlpool

Whirlpool W10330947A User manual

Whirlpool

Whirlpool Duet Steam User manual

Whirlpool

Whirlpool LA6055XS User manual

Whirlpool

Whirlpool AWO 3361 User manual

Whirlpool

Whirlpool WFW9400SW - Duet HT Series User manual

Whirlpool

Whirlpool AWM 285/3 User manual

Whirlpool

Whirlpool LSR6332KQ1 User manual

Whirlpool

Whirlpool WIII User manual

Whirlpool

Whirlpool WTW5010LW User manual

Whirlpool

Whirlpool LSV9244DQ0 User manual

Whirlpool

Whirlpool AWM 9100 GH User manual

Whirlpool

Whirlpool LA5578XS User manual

Whirlpool

Whirlpool Maytag 7MMVWC465JW User manual

Whirlpool

Whirlpool ALA 101 User manual

Whirlpool

Whirlpool AL5143V User manual

Whirlpool

Whirlpool LA6500XP User manual

Whirlpool

Whirlpool W10200828B User manual

Whirlpool

Whirlpool Cabrio WTW6400SW2 User manual

Popular Washer manuals by other brands

Tricity Bendix

Tricity Bendix AW 1000 W Operating & installation instructions

Panasonic

Panasonic NA-F60L5WRB operating instructions

GE WSLP1500 Dimensions and installation information

Electrolux

Electrolux EWF1284EDW Service manual

Bosch

Bosch WAN2829BSN User manual and installation instructions

LG TV2516DV3B owner's manual

LG TH2517DSAV owner's manual

VESTEL

VESTEL CMH-XL 7510 TE user manual

AEG

AEG 74335 User information

Johnson

Johnson JWF721A user manual

Beko

Beko WTE7604XLW0 owner's manual

Danby

Danby DTT100A1WDB Owner's use and care guide

Amica

Amica WA 14 Ex operating instructions

Daewoo

Daewoo DWD-F1222 instruction manual

Bosch

Bosch WAS28461AU instruction manual

Miele

Miele PW 6080 Vario manual

Finlux

Finlux FLX108CF220 user manual

Beko

Beko WKB 51231 PTMA manual