WELLTEC parcelkiosk Bedal 3S User manual
Welltec-UM-Bedal_171206_EN_Rev.07
User Manual Bedal 3S
Ver. 07
User Manual Bedal 3S
Introduction
Installation
1
Operation
Introduction 2
Operating Condition 3
Contents
Enclosed Parts 8
About Bedal 4
Measuring Dimension & Weight 19
Specifications 5
Precautions
Error Code 22
Description of Units 6
H/W Installation 9
S/W Installation 17
Interface Flow 18
Measurable / Non-Measurable Items 26
Warranty 27
Operational Precautions 23
Ver. 07
User Manual Bedal 3S
2
Welcome!
Thank you for selecting Bedal 3S.
This manual is prepared to provide you with guidelines on how to properly operate and
Maintain Bedal 3S. Please read this user manual before operating in order to prevent
unexpected malfunction or damage. Please refer to the manual carefully and follow the
instruction.
Copyright
Any of the contents should not be copied, re-printed or translated into other languages
without Welltec’s approval.
Introduction
Introduction
Ver. 07
User Manual Bedal 3S
Operating Condition
3
Caution: Serious bodily injury or mechanical damage may result from
insufficient attention to or incorrect compliance with warning
messages with this symbol.
●Do not attempt to disassemble or reassemble the machine. It may cause an electric
shock or mechanical problem.
●Disconnect the power immediately if liquid or a foreign object enter the inside of the
machine.
●Do not input metal or inflammable material into the inlet.
●Remove the power cable while moving the machine.
●Where the wind is directly blowing to the machine(air conditioner, fan, etc), it may
cause weighing error and extra time for measurement(need to secure stability).
●Be careful not to place object that exceeds the allowable load of Bedal 3S, as this will
cause the malfunction. (Even if no power is applied, overload might cause permanent
damage)
●Be careful not to place the machine where the rear cover is in contact with wall.
(Measurement error or unstable might occur due to vibration)
●Please avoid to install at places like below :
- Near window or places exposed to direct sunlight.
- Where vibration is detected or unstable place (causing measurement errors)
- Where temperature changes suddenly or poorly ventilated.
- Places exposed to hot or cold air directly. (not office circumstance)
- Not solid enough or weak floor.
- Near excessive electromagnetic waves are generated (causing measurement errors)
- Where strong winds blow (measurement time may be increased)
●Temperature: -10℃ ~ 40℃
●Humidity: 10~85%RH, Non-Condensing.
Introduction
Ver. 07
User Manual Bedal 3S
About Bedal
4
Bedal 3S is an electronic Dimensional Scanner that automatically measures the
weight and dimension of parcels. It transmits captured dimension, weight,
image and other data to the host like Windows based PC, Tablet or TCP/IP linked
server. Not working as a standalone, Bedal 3S is an Input Device required to be
linked to your computer. Bedal 3S will pay for itself, enjoy automatic measuring and
experience your time with saving cost!
Introduction
Ver. 07
User Manual Bedal 3S
Specifications
5
* Specification is subject to be revised without notice.
Introduction
No
Criteria Specification (Module)
1
Installation Type
Stand Alone
Desktop type
2
Display
Dimensions
6 Digit FND x
3
Weighing
6 Digit FND x
1
3
Regular Shape
Dimension
Min & Max
Width
10 cm ~ 410 cm
Length
10 cm ~ 43 cm
extendable 43 cm to 75 cm
Height
4 cm ~ 48 cm
Division
Width
0.5 cm
Length
Height
Tolerance
Width
±
0.5 cm
Length
±
1 cm
Height
±
0.5 cm
4
Weighing
Min & Max
0.25 kg ~ 32
kg
Division
0.05kg
Tolerance
Under 25 kg
±
0.05 kg
Over 25 kg
±
0.1 kg
5
Light Signal
LED
Green light
On
Green light
Blinking
Red light
On
Red light
Blinking
Ready
Processing
Error
Not Ready
6
Sound
Buzzer
Beep Sound (built
-in on board)
7
Measuring Time
Regular
Max
3 seconds
8
Camera
Web Cam
1M Pixel (TBD)
9
Ethernet
LAN
IEEE 802.3 10/100Mbps Ethernet port (RJ
-45), 1ea
10
Interface
USB Hub Port
USB 2.0 (A type) x
4ea
USB 2.0 (B type) x
1ea
RS-232C
D
-SUB 9Pin (male) x 1ea
D
-SUB 9Pin (female) x 1ea
11
Size
Standard
558mm(L) X 567mm(W) X 847mm(H)
Side Extendable
874mm(L) X 567mm(W) X 847mm(H)
12
Operating Condition
Indoor Temperature
15℃
~ 40℃
Humidity
10~85%RH Non
-condensing
13
Input Power
AC Adapter
100
-240 VAC ~ 50/60Hz 1.5A
14
Power Consumption
17 W max
15
Acoustic Sound Level
48 dB(A) max (Beep sound excluded)
16
Weight
Without Packing
23kg (28kg/With Packing)
17
Compliance
International
CE
Korea
KC / Scale Certification
Ver. 07
User Manual Bedal 3S
Description of Units
6
· LED: Green and red LED lights for operation status.
· Speaker: Voice instruction of operation.
· Object Detect Sensor : Start measuring the weight and dimension of the object by sensing the
object placed on the Weight Measurement.
· Sensor (Height Measure): Measure the height of object.
· Sensor (Length Measure): Measure the length of object. (1 side extendable)
· Sensor (Width Measure): Measure the width of object.
· Weight Measurement: Measure the weight of object.
· Camera : To capture the object image
· Indicator : Display measured dimension and weight information.
Front
1
Introduction
Speaker
Camera
Object Detect Sensor
Indicator
Sensor (Length Measure)
*Extendable
Weight Measurement
Sensor (Width Measure)
LED
Sensor (Height Measure)
Ver. 07
User Manual Bedal 3S
7
Rear
2
I/O
Interface Power S/W
Serial Label
DC Power
Jack
USB 2.0
A Type
USB B Type
RS-232C (M)
RS-232C (F)
LAN (RJ45)
USB 2.0 USB 2.0
* Printer will use the power source separately.
* PC will use PC LAN Port for internet connection, Tablet PC need Wi-Fi (customer installation).
* PC (control) or server need to be able to download operation program.
* D-Sub (M/F) is for Firmware Update.
* Display Port is for exterior display unit. (optional)
* USB 3.0 (Host Port) is used as printer port when Bedal 3S is the host of the configuration.
Indicator
Port
Description of Units
Introduction
Ver. 07
User Manual Bedal 3S
8
Check all parts are included after unpacking.
1
Enclosed Parts
Installation
①Main Body
●Main Units
●Adaptor & Cable
①DC Adaptor ②Power Cable
●Screws
①Truss M4X10L * 6pcs
③USB Cable (A-B)
②Upper Unit ③Indicator
Ver. 07
User Manual Bedal 3S
9
After unpacking, remove 4 screws marked as circle on the below picture &
remove the rear cover. (keep the screws)
1
H/W Installation
Installation
Table of contents
Other WELLTEC Scanner manuals
