Weinmann ULM CASE I User manual

ULM CASE I / VALISE ULM I /

VALIGIA ULM I

Emergency Case / Valise d'urgence /

Valigia per l'emergenza medica WM 8840

Description and instructions for use /

Description de l'appareil et mode d'emploi /

Descrizione dell'apparecchio e istruzioni per l'uso

English 3

Français 20

Italiano 38

EN 3

Contents

1 Overview....................................................................... 4

1.1 Special markings on the device............................... 5

2 Device Description.......................................................... 6

2.1 Purpose of use ..................................................... 6

2.2 Functional description............................................ 6

3 Safety Instructions .......................................................... 7

4 Assembly....................................................................... 8

4.1 Assembly of wall mounting ..................................... 8

5 Operation...................................................................... 9

5.1 Space Dividers .................................................... 9

5.2 Tube Holders ....................................................... 9

5.3 Ampoule Holders ................................................. 9

5.4 Inserting Oxygen Cylinders .................................. 10

5.5 MEDUMAT Holder ............................................. 10

5.6 OMNIVAC holder ............................................. 11

6 Hygiene preparation .................................................... 11

7 Functional Test.............................................................. 12

8 Maintenance ................................................................ 12

8.1 Intervals............................................................ 12

8.2 Disposal ........................................................... 13

9 Supply Schedule........................................................... 13

9.1 Standard Supply Schedule ................................... 13

9.2 Accessories ....................................................... 14

9.3 Replacement Parts ..............................................14

10 Technical Speciﬁcations................................................. 16

11 Warranty..................................................................... 17

12 Declaration of conformity ............................................. 18

4EN Overview

Legend

1 Magnetic closing

2 Cover

3 Case top

4 Upper insert

5 Short (121mm) bottom divider

6 Retaining clamp

7 Oxygen cylinder compartment

8 Lower insert

9 Case bottom

10 Case lock

11 Case handle

12 Long (211mm) bottom divider

1 Overview

13 Lead seal

14 Medium (147 mm) bottom divider

15 Tube holder:

a) Oropharyngeal tubes, large

b) Oropharyngeal tubes, small

16 Keys

Set of two belts for oxygen cylinder

18 Laryngoscope bag

Ampoule holder 200 mm (10 places for ampoules)

Ampoule holder 260 mm (13 places for ampoules)

21 Ampoularium

22 MEDUMAT holder

23 OMNIVAC holder

Overview EN 5

1.1 Special markings on the device

No. Symbol Meaning

Device ID plate ULM CASE I

1 SN Serial number

Year of manufacture

CE marking

Other markings

2Removing the bars

6EN Device Description

2 Device Description

2.1 Purpose of use

ULM CASE I is used to hold and transport emergency

medical devices, instruments, medicines, bandages and

other parts.

2.2 Functional description

ULM CASE I has been perfectly equipped for each time

of use. The interior of the case bottom can be set up with

dividers to ﬁt your speciﬁc needs. Accessories, such as am-

poule holders, tube holders and belts for oxygen cylinders

provide further customization potential.

ULM CASE I can also be equipped with individual holders

for the ventilation device MEDUMAT and the OMNIVAC

suction system.

Safety Instructions EN 7

3 Safety Instructions

For your own safety, the safety of your patients, and to

comply with the requirements of EU Directive 93/42/

EEC, please observe the following points:

• Please follow the instructions in this User’s Manual. They

are a part of the case and therefore must be available

at all times.

• Prerequisites for use of this case include thorough

knowledge and observation of this User’s Manual.

• The case is intended only for the described purpose.

• If third-party items are used, functional failures may oc-

cur and ﬁtness for use may be restricted. Biocompatibi-

lity requirements may also not be met. Please note that

in such cases, any claim under warranty and liability

will be voided if neither the accessories nor genuine

replacement parts recommended in the instructions for

use are used.

• Be sure that spilled liquids (for example, from ampou-

les) are cleaned up immediately. Observe the warning

and disposal regulations of the manufacturers involved.

• To prevent infection or bacterial contamination, observe

the instructions in Section “6 Hygiene preparation” on

page 11.

• If the case is equipped with oxygen cylinders and other

devices, be sure to observe the accompanying User’s

Manuals and special instructions.

• Protect the oxygen cylinders from accidents.

• Keep the devices free from oil and grease.

• Make sure you wash your hands before handling

oxygen cylinders.

• When assembling the parts and when changing cylinders,

turn all screws by hand. Do not in any event use tools.

• Always open the cylinder valve slowly.

• Smoking and open ﬂames are strictly forbidden in the

vicinity of oxygen-related equipment.

• Make sure you always have adequately ﬁlled oxygen

cylinders. It is recommended that you keep a full

oxygen cylinder in reserve.

8EN Assembly

4 Assembly

4.1 Assembly of wall mounting

If you would like to mount the case on the wall of a

vehicle, use wall mounting WM 15370 (see Section “9

Supply Schedule” on page 13).

If you would like to mount the case on the wall of a buil-

ding, use the appropriate wall mounting WM 15731 (see

Section “9 Supply Schedule” on page 13).

1. Mark the spots for the holes on the surface where you

want to fasten the case.

You can use the wall mounting as a stencil.

2. Drill the holes:

– in vehicles: with a drill bit of 3 mm in diameter

– in buildings: with an appropriate bit for the requi-

red dowel.

3. Screw the wall mounting tightly into place.

Wall mounting WM 15370

Wall mounting WM 15371

Operation EN 9

5 Operation

5.1 Space Dividers

The interior of the case bottom can be separated as desi-

red with the space dividers (5, 12 and 14). See Illustration

1, Device Overview, for an example.

Observe the following when using the dividers:

• proper positioning as illustrated

• right-angle placement in the opposing grooves

• correct clicking-in of the snap elements

To remove a divider, press both circular snap elements

together (as shown) and lift the divider.

5.2 Tube Holders

The manufacturer has supplied tube holders 15 a) and

15 b) as sets with the fastening elements. You can fasten

the tube holders to any divider in the case bottom (see

illustration).

5.3 Ampoule Holders

The ampoule holders (19 and 20), delivered as a set with

the fastening elements or as replacement parts, can be

attached (as shown) to the desired spot on the inside of the

cover (2)).

Important!

Make sure that when you close the cover, no ampoules

are crushed by a divider or other equipment.

WEINMANN : HAMBURG

10 EN Operation

5.4 Inserting Oxygen Cylinders

Be sure to wash your hands before you insert or change

oxygen cylinders.

If you want to fasten an oxygen cylinder of 0.8 liters or

2.0 liters into the case bottom

(9), use accessory WM 15141, Set of two belts for

oxygen cylinders (17). Fasten the oxygen cylinder in the

oxygen cylinder compartment (7) as shown in the illustra-

tion. To fasten a 2.0-liter oxygen cylinder, use the outer

clamp (6) on the ﬂoor of the case. If you want to fasten an

0.8-liter cylinder, use the middle and left clamps. Be sure

that you pull the belts tightly during assembly in order to

prevent the cylinders from slipping out of place.

5.5 MEDUMAT Holder

To fasten a MEDUMAT ventilation device into the case

bottom, use the holder for MEDUMAT (22). Click the ME-

DUMAT holder into place in the case bottom as shown in

the illustration. Then place the MEDUMAT so that the lower

grid on the device catches in the gap in the holder. Press

the MEDUMAT up into the holder until you hear it click into

place.

Important!

Your hands must be free of

grease and products contai-

ning alcohol when you insert

or change oxygen cylinders.

Fire hazard!

WEINMANN : HAMBURG

This manual suits for next models

Table of contents

Languages:

Other Weinmann Medical Equipment manuals

Weinmann

Weinmann COMBIBAG WM 11000 Manual

Weinmann

Weinmann SOMNOvent CR User manual

Weinmann

Weinmann Module System User manual

Weinmann

Weinmann VENTIsupport Manual

Weinmann

Weinmann RESCUE-PACK Plus User manual

Weinmann

Weinmann JOYCEeasy User manual

Weinmann

Weinmann MEDUMAT Easy CPR User manual

Weinmann

Weinmann COMBIBAG User manual

Weinmann

Weinmann prismaPSG WM 100 MP User manual

Weinmann

Weinmann MEDUMAT Standard2 User manual

Weinmann

Weinmann MEDUVENT Standard User manual

Weinmann

Weinmann SOMNOvent auto-S Reference guide

Weinmann

Weinmann PARAMEDIC BOX User manual

Weinmann

Weinmann MEDUMAT Transport User manual

Weinmann

Weinmann SOMNOvent CR User manual

Weinmann

Weinmann homecare SOMNOcomfort 2 Setup guide

Weinmann

Weinmann SOMNOcomfort 2e Technical Document

Weinmann

Weinmann WM 24900 User manual

Weinmann

Weinmann MEDUVENT Standard User manual

Weinmann

Weinmann ULM CASE Circulation Technical Document

Weinmann

Weinmann Oxygen MODULE Setup guide

Weinmann

Weinmann MEDUCORE Standard2 User manual

Weinmann

Weinmann ULM CASE User manual

Weinmann

Weinmann MEDUMAT EasyCPR User manual

Popular Medical Equipment manuals by other brands

TekTone

TekTone Tek-CARE160 Installation and operation manual

NeuroMetrix

NeuroMetrix Quell 2.0 user manual

AMT

AMT XLR8 Quick reference guide

Medipost-Nutristoma

Medipost-Nutristoma MD300K2 instruction manual

EDAN

EDAN SONOTRAX Pro user manual

Restorative Therapies

Restorative Therapies RT300 Service guide

Gendex

Gendex Expert DC installation manual

Dexcowin

Dexcowin ADX4000W user manual

Libelium

Libelium MySignals user manual

Acelity

Acelity V.A.C.ULTA 4 user manual

Caputron

Caputron ActivaDose II tDCS quick start guide

FujiFilm

FujiFilm Sonart Features

Plinth 2000

Plinth 2000 93CDT Service manual

GE SENOGRAPHE 800T Operator's manual

GE Definium 5000 Operator's manual

Kanmed

Kanmed GE-1380 user manual

Huntleigh

Huntleigh FD1 Instructions for use

Stryker

Stryker SPR Plus Operation manual