weBoost DRIVE X User manual
ENGLISH
FRANÇAIS
Installation Guide
Vehicle Signal Booster Kit
DRIVE X
A WILSON ELECTRONICS BRAND
NEED HELP? weboost.ca 866.294.1660
______
Index
Package Contents......................................................................................... 1
STEP 1:Mount Outside Magnetic Antenna........................................ 2
STEP 2:Mount Inside Antenna.............................................................. 4
STEP 3:Connect Coax Cables To Booster......................................... 5
STEP 4:Connect Power Supply To Booster....................................... 6
STEP 5:
Plug Power Adapter Into Vehicle’s Power Supply................7
Light Patterns.................................................................................................8
Troubleshooting ................................................................................... 9
Safety Guidelines.............................................................................10
Specifications.....................................................................................11
Warranty.............................................................................................12
DRIVE X VEHICLE SIGNAL BOOSTER 1
ENGLISH
________
Package
Contents
Booster
& Bracket
Outside
Antenna
Inside
Antenna
Power
Supply
Optional: Adhesive disk for aluminum vehicles
2VEHICLE SIGNAL BOOSTER DRIVE X
ENGLISH
______
Step 1: Mount Outside
Magnetic Antenna
WORKS WITH ALL VEHICLES
Identify a location on the top of your vehicle that is:
Near the center of the roof
At least 12 inches away from any other antennas and
from any windows (including sunroofs)
Clean the surface where you will place the outside
antenna.
Mount the outside antenna by placing on top of vehicle.
12 in. away from windows
(including sunroofs)
NOTE: For aluminum roofs, use the included adhesive disk to secure outside
antenna in place.
DRIVE X VEHICLE SIGNAL BOOSTER 3
ENGLISH
NOTE: When going through car wash,
remember to remove your antenna.
NOTE: The cable is strong enough that it may be shut in most vehicle doors
without damaging the cable.
Car/Sedan: Cable routed
into rear side door.
SUV/Van/Hatchback: Cable
routed into top of hatchback door.
Truck: Cable routed into
side door.
______
(STEP 1 cont.)
See options below on how cable can be routed with
different vehicles.
4VEHICLE SIGNAL BOOSTER DRIVE X
ENGLISH
______
Step 2: Mount Inside Antenna
Identify a place to mount the In-Vehicle Antenna, either on the
side of the seat or on the dash and mount. The location should
be at least 18 inches but no more than 36 inches from where
the cell phone device will be used. Use the Velcro® adhesive
strip/adhesive strip provided and attach to
desired location.
In-Vehicle
Antenna
In-Vehicle Antenna
DRIVE X VEHICLE SIGNAL BOOSTER 5
ENGLISH
______
Step 3: Connect Coax Cables
To Booster
Connect the cable from the Mini-Mag Mount Antenna to the
port labeled “Outside Antenna” on the Drive X booster.
Connect the cable from the In-Vehicle Antenna to the port
labeled “Inside Antenna” on the booster.
In-Vehicle
Antenna
from Outside Antenna
from Inside Antenna
NOTE: Bracket can be used to fasten booster in a specific location if desired.
6VEHICLE SIGNAL BOOSTER DRIVE X
ENGLISH
______
Step 4: Connect Power
Supply To Booster
Connect the power supply cord to the end of the Drive X
labeled “Power.”
NOTE: Do NOT connect the power to the Signal Booster until you have
connected both the Inside and Outside Antennas.
Power Supply
DRIVE X VEHICLE SIGNAL BOOSTER 7
ENGLISH
______
Step 5: Plug Power Adapter
Into Vehicle’s Power Supply
Plug the power adapter into vehicle’s 12V DC power supply.
Power up your Drive X by flipping the switch on the back of
the DC power adapter on. If your Drive X is working correctly,
the light on the power adapter will be red, and the light on the
booster will be green.
DC Power Adapter
NEED HELP? weboost.ca 866.294.1660
8VEHICLE SIGNAL BOOSTER DRIVE X
ENGLISH
______
Light Patterns
Solid Green
This indicates that your booster is functioning properly and there are no issues with
installation.
Blinking Red, Then Solid Green
This indicates that one or more of the booster bands has reduced power due
to a feedback loop condition called oscillation. This is a built in safety feature
to prevent harmful interference with a nearby cell tower. If you are already
experiencing the desired signal boost, then no further adjustments are necessary.
If you are not experiencing the desired boost in coverage then refer to the
Troubleshooting section below.
Solid Red
This is due to a feedback loop condition called oscillation. This is a built in safety
feature that causes a band to shut off to prevent harmful interference with a nearby
cell tower. Refer to Troubleshooting section below.
Light O
If the Drive X Signal Booster’s light is off, verify your power supply has power.
NOTE: The Signal Booster can be reset by disconnecting and reconnecting
the power supply.
After troubleshooting you must initiate a new power cycle by disconnecting and
then reconnecting power to the Booster.
NEED HELP? weboost.ca 866.294.1660
This manual suits for next models
2
Table of contents
Languages:
Other weBoost Extender manuals
weBoost
weBoost Drive 3G-X User manual
weBoost
weBoost Drive 4G-M User manual
weBoost
weBoost DRIVE 3G-S User manual
weBoost
weBoost Connect RV 65 User manual
weBoost
weBoost Office 200 User manual
weBoost
weBoost Home MultiRoom User manual
weBoost
weBoost 460066 User manual
weBoost
weBoost DRIVE 4G-X FLEET User manual
weBoost
weBoost Home Room User manual
weBoost
weBoost DRIVE 4G-X FLEET User manual
weBoost
weBoost DRIVE 4G-X RV User manual
weBoost
weBoost eqo 460032 User manual
weBoost
weBoost Home 4G User manual
weBoost
weBoost DRIVE 4G-X FLEET User manual
weBoost
weBoost eqo User manual
weBoost
weBoost Drive AM100-Pro User manual
weBoost
weBoost DRIVE SLEEK OTR User manual
weBoost
weBoost Drive 4G-M User manual
weBoost
weBoost Drive 4G-M User manual
weBoost
weBoost Drive 3G-X User manual
