Wattstopper LMZC-301 User manual

Installation Instructions

LMZC-301

DLM Zone Controller

Step 1

Remove the P115/277 board with the LMPI assembly

Step 2

Mount the LMCZ-301, using 4 mounting screws.

Step 3

Reinstall the P115/277 board with the LMPI assembly

Note: If installing an optional LMRC-100s, attach it to the

power supply board before reinstalling. See the instructions

at the bottom of the following page.

Step 4

Connect the incoming power cable to the power supply (and if used,

to the LMRC-100).

Green

(Ground)

White

(Neutral)

Black

(Line)

Black

(Line)

Green

(Ground)

White

(Neutral)

Connect as shown below for 115V Connect as shown below for 277V

SPECIFICATIONS

Input voltage..................................................115/277V 60 Hz

Class 2 connection to two independent DLM local networks (IRB)

24VDC output, up to 250mA across 2 RJ45 ports per

local network (A and B networks, 250 mA each)

If using an optional LMRC-100 to boost output, the

amount is 400 mA per network (two LMRC-100s

needed if using both networks)

Free-topology DLM local network segments may include

LMFC-011 Fixture Controllers, DLM switches, occupancy

sensors, daylight sensors and input modules

Category 5e cable, up to 1,000 ft. total per local network

Terminals for connection to DLM segment network

(BACnet MS/TP)

Segment network parameters

WattStopper LM-MSTP wire

Linear topology; 4000 ft. maximum per segment

Operating conditions:

for indoor use only ...................... 32-122 F (0 – 50 C)

........................................5-95% RH, non-condensing

UL and cUL listed

Green

(Ground)

White

(Neutral)

Black

(Line)

Green

(Ground)

White

(Neutral)

Black

(Line)

Wiring for an LMRC-100 Wiring for two LMRC-100s

Installation Instructions

LMZC-301

DLM Zone Controller

Step 1

Remove the P115/277 board with the LMPI assembly

Step 2

Mount the LMCZ-301, using 4 mounting screws.

Step 3

Reinstall the P115/277 board with the LMPI assembly

Note: If installing an optional LMRC-100s, attach it to the

power supply board before reinstalling. See the instructions

at the bottom of the following page.

Step 4

Connect the incoming power cable to the power supply (and if used,

to the LMRC-100).

Green

(Ground)

White

(Neutral)

Black

(Line)

Black

(Line)

Green

(Ground)

White

(Neutral)

Connect as shown below for 115V Connect as shown below for 277V

SPECIFICATIONS

Input voltage..................................................115/277V 60 Hz

Class 2 connection to two independent DLM local networks (IRB)

24VDC output, up to 250mA across 2 RJ45 ports per

local network (A and B networks, 250 mA each)

If using an optional LMRC-100 to boost output, the

amount is 400 mA per network (two LMRC-100s

needed if using both networks)

Free-topology DLM local network segments may include

LMFC-011 Fixture Controllers, DLM switches, occupancy

sensors, daylight sensors and input modules

Category 5e cable, up to 1,000 ft. total per local network

Terminals for connection to DLM segment network

(BACnet MS/TP)

Segment network parameters

WattStopper LM-MSTP wire

Linear topology; 4000 ft. maximum per segment

Operating conditions:

for indoor use only ...................... 32-122 F (0 – 50 C)

........................................5-95% RH, non-condensing

UL and cUL listed

Green

(Ground)

White

(Neutral)

Black

(Line)

Green

(Ground)

White

(Neutral)

Black

(Line)

Wiring for an LMRC-100 Wiring for two LMRC-100s

Installation Instructions

LMZC-301

DLM Zone Controller

Step 1

Remove the P115/277 board with the LMPI assembly

Step 2

Mount the LMCZ-301, using 4 mounting screws.

Step 3

Reinstall the P115/277 board with the LMPI assembly

Note: If installing an optional LMRC-100s, attach it to the

power supply board before reinstalling. See the instructions

at the bottom of the following page.

Step 4

Connect the incoming power cable to the power supply (and if used,

to the LMRC-100).

Green

(Ground)

White

(Neutral)

Black

(Line)

Black

(Line)

Green

(Ground)

White

(Neutral)

Connect as shown below for 115V Connect as shown below for 277V

SPECIFICATIONS

Input voltage..................................................115/277V 60 Hz

Class 2 connection to two independent DLM local networks (IRB)

24VDC output, up to 250mA across 2 RJ45 ports per

local network (A and B networks, 250 mA each)

If using an optional LMRC-100 to boost output, the

amount is 400 mA per network (two LMRC-100s

needed if using both networks)

Free-topology DLM local network segments may include

LMFC-011 Fixture Controllers, DLM switches, occupancy

sensors, daylight sensors and input modules

Category 5e cable, up to 1,000 ft. total per local network

Terminals for connection to DLM segment network

(BACnet MS/TP)

Segment network parameters

WattStopper LM-MSTP wire

Linear topology; 4000 ft. maximum per segment

Operating conditions:

for indoor use only ...................... 32-122 F (0 – 50 C)

........................................5-95% RH, non-condensing

UL and cUL listed

Green

(Ground)

White

(Neutral)

Black

(Line)

Green

(Ground)

White

(Neutral)

Black

(Line)

Wiring for an LMRC-100 Wiring for two LMRC-100s

Installation Instructions

LMZC-301

DLM Zone Controller

Step 1

Remove the P115/277 board with the LMPI assembly

Step 2

Mount the LMCZ-301, using 4 mounting screws.

Step 3

Reinstall the P115/277 board with the LMPI assembly

Note: If installing an optional LMRC-100s, attach it to the

power supply board before reinstalling. See the instructions

at the bottom of the following page.

Step 4

Connect the incoming power cable to the power supply (and if used,

to the LMRC-100).

Green

(Ground)

White

(Neutral)

Black

(Line)

Black

(Line)

Green

(Ground)

White

(Neutral)

Connect as shown below for 115V Connect as shown below for 277V

SPECIFICATIONS

Input voltage..................................................115/277V 60 Hz

Class 2 connection to two independent DLM local networks (IRB)

24VDC output, up to 250mA across 2 RJ45 ports per

local network (A and B networks, 250 mA each)

If using an optional LMRC-100 to boost output, the

amount is 400 mA per network (two LMRC-100s

needed if using both networks)

Free-topology DLM local network segments may include

LMFC-011 Fixture Controllers, DLM switches, occupancy

sensors, daylight sensors and input modules

Category 5e cable, up to 1,000 ft. total per local network

Terminals for connection to DLM segment network

(BACnet MS/TP)

Segment network parameters

WattStopper LM-MSTP wire

Linear topology; 4000 ft. maximum per segment

Operating conditions:

for indoor use only ...................... 32-122 F (0 – 50 C)

........................................5-95% RH, non-condensing

UL and cUL listed

Green

(Ground)

White

(Neutral)

Black

(Line)

Green

(Ground)

White

(Neutral)

Black

(Line)

Wiring for an LMRC-100 Wiring for two LMRC-100s

Installation Instructions

LMZC-301

DLM Zone Controller

Step 1

Remove the P115/277 board with the LMPI assembly

Step 2

Mount the LMCZ-301, using 4 mounting screws.

Step 3

Reinstall the P115/277 board with the LMPI assembly

Note: If installing an optional LMRC-100s, attach it to the

power supply board before reinstalling. See the instructions

at the bottom of the following page.

Step 4

Connect the incoming power cable to the power supply (and if used,

to the LMRC-100).

Green

(Ground)

White

(Neutral)

Black

(Line)

Black

(Line)

Green

(Ground)

White

(Neutral)

Connect as shown below for 115V Connect as shown below for 277V

SPECIFICATIONS

Input voltage..................................................115/277V 60 Hz

Class 2 connection to two independent DLM local networks (IRB)

24VDC output, up to 250mA across 2 RJ45 ports per

local network (A and B networks, 250 mA each)

If using an optional LMRC-100 to boost output, the

amount is 400 mA per network (two LMRC-100s

needed if using both networks)

Free-topology DLM local network segments may include

LMFC-011 Fixture Controllers, DLM switches, occupancy

sensors, daylight sensors and input modules

Category 5e cable, up to 1,000 ft. total per local network

Terminals for connection to DLM segment network

(BACnet MS/TP)

Segment network parameters

WattStopper LM-MSTP wire

Linear topology; 4000 ft. maximum per segment

Operating conditions:

for indoor use only ...................... 32-122 F (0 – 50 C)

........................................5-95% RH, non-condensing

UL and cUL listed

Green

(Ground)

White

(Neutral)

Black

(Line)

Green

(Ground)

White

(Neutral)

Black

(Line)

Wiring for an LMRC-100 Wiring for two LMRC-100s

WARRANTY INFORMATION

WattStopper warranties its products to be free of defects in materials and workmanship for a period of five (5) years. There are no obligations

or liabilities on the part of WattStopper for consequential damages arising out of, or in connection with, the use or performance of this product

or other indirect damages with respect to loss of property, revenue or profit, or cost of removal, installation or reinstallation.

Phone: 800-879-8585

www.wattstopper.com

Please

Recycle

2800 De La Cruz Boulevard

Santa Clara, CA 95050

4/2015

21256r1

Step 5

Attach the ground wire.

Step 6

Connect the Power Supply to the LMPI board.

Red

Black

Step 7

Connect one or more LMRJ cables to the RJ45 jacks. There are two DLM IRB networks (labeled A & B) used to connect DLM devices such

as the LMFC-011 Fixture Controllers, switches, sensors, and room controllers. The networks are labeled A and B. Each network has two

RJ-45 jacks, for connecting CAT5 cable. It is not important which of the two jacks are used.

Note: RJ45 jacks/Cat5 cables are only used to connect to DLM switches, sensors, room controllers, etc. to the panel. To connect one

panel to another panel, use the MS/TP connectors

Once installation is complete, re-attach the cover to the LMCZ-301.

Network A

Network B

IR for LMCT

Communication

MS/TP Connector for

Segment Network

Power

Connection

Optional Installation of LMRC-100

In situations where a larger number of devices

are connected to a DLM network, you can

increase the amount of power output from

the LMZC-301 by installing a powered room

controller on either Cat 5e network (which

adds power to just that network), or by

installing one or two LMRC-100s within the

unit (one per network). Secure the LMRC-100

to the power supply board on the LMZC-301,

as shown to the right. Then, connect an LMRJ

cable from the LMRC-100 to the LMZC-301.

Note: If using an LMRC-100, maximum

operating condition is 104 F (40 C)

Knock out for mounting second LMRC-100 Note: An LMRC-100 should be only

connected to Network A or B only. To

use both Networks, you will need to

install two LMRC-100s.

WattStopper recommends

using grommets to protect

CAT5 cables routed

through knock out holes

Installation Instructions

LMZC-301

DLM Zone Controller

Step 1

Remove the P115/277 board with the LMPI assembly

Step 2

Mount the LMCZ-301, using 4 mounting screws.

Step 3

Reinstall the P115/277 board with the LMPI assembly

Note: If installing an optional LMRC-100s, attach it to the

power supply board before reinstalling. See the instructions

at the bottom of the following page.

Step 4

Connect the incoming power cable to the power supply (and if used,

to the LMRC-100).

Green

(Ground)

White

(Neutral)

Black

(Line)

Black

(Line)

Green

(Ground)

White

(Neutral)

Connect as shown below for 115V Connect as shown below for 277V

SPECIFICATIONS

Input voltage..................................................115/277V 60 Hz

Class 2 connection to two independent DLM local networks (IRB)

24VDC output, up to 250mA across 2 RJ45 ports per

local network (A and B networks, 250 mA each)

If using an optional LMRC-100 to boost output, the

amount is 400 mA per network (two LMRC-100s

needed if using both networks)

Free-topology DLM local network segments may include

LMFC-011 Fixture Controllers, DLM switches, occupancy

sensors, daylight sensors and input modules

Category 5e cable, up to 1,000 ft. total per local network

Terminals for connection to DLM segment network

(BACnet MS/TP)

Segment network parameters

WattStopper LM-MSTP wire

Linear topology; 4000 ft. maximum per segment

Operating conditions:

for indoor use only ...................... 32-122 F (0 – 50 C)

........................................5-95% RH, non-condensing

UL and cUL listed

Green

(Ground)

White

(Neutral)

Black

(Line)

Green

(Ground)

White

(Neutral)

Black

(Line)

Wiring for an LMRC-100 Wiring for two LMRC-100s

Other manuals for LMZC-301

Table of contents

Other wattstopper Controllers manuals

wattstopper

wattstopper DRD6 v2 User manual

wattstopper

wattstopper MRDS10 User manual

wattstopper

wattstopper LightSaver LS-100XA Service manual

wattstopper

wattstopper LMRC-111 User manual

wattstopper

wattstopper LMZC-301 User manual

wattstopper

wattstopper LMPL-101 User manual

wattstopper

wattstopper DRD8 v2 User manual

wattstopper

wattstopper LS-101 User manual

wattstopper

wattstopper LMRC-101 User manual

wattstopper

wattstopper legrand LMRC-102 User manual

wattstopper

wattstopper LMRC-222 User manual

wattstopper

wattstopper WRC-15 Series User manual

wattstopper

wattstopper LMPL-201 User manual

wattstopper

wattstopper WRC-15 Series User manual

Popular Controllers manuals by other brands

Digiplex

Digiplex DGP-848 Programming guide

YASKAWA

YASKAWA SGM series user manual

Sinope

Sinope Calypso RM3500ZB installation guide

Isimet

Isimet DLA Series Style 2 Installation, Operations, Start-up and Maintenance Instructions

LSIS

LSIS sv-ip5a user manual

Rockwell Automation

Rockwell Automation 1769-L31 installation instructions

Airflow

Airflow Uno hab Installation and operating instructions

ABB

ABB ACS580-01 drives Hardware manual

Panasonic

Panasonic GM1 Series Reference manual

Emerson

Emerson SW93 owner's manual

AutoAqua

AutoAqua Smart ATO micro SATO-120P manual

Panasonic

Panasonic FP? Positioning Unit RTEX Technical manual

Samson

Samson Type 5824 Mounting and operating instructions

Alpha IP

Alpha IP MIOB 21001 manual

Siemens

Siemens OpenAir GMA 1 Series Mounting instructions

Surecom

Surecom SR-629 user manual

Fishman

Fishman TriplePlay installation guide

Regulus

Regulus SRS1 T Installation and operation manual