Wasp WWS150i User manual

WWS150i

Quick Start Guide

Table of Contents

Quick Start 2

1. Unpack 2

2. Charging the WWS150i 2

3. Connecting the Scanner to a Bluetooth Device 2

Setup & Configuration 3

Factory Default 4

Check Version 4

Link Quality On/Off 4

Set Connection 4

Bluetooth SPP (Bluetooth COM) 5

Bluetooth HID (Keyboard) 5

Terminator 6

iPad/iPhone Toggle Keyboard 6

Enable/Disable iOS Hotkeys 7

QSG

Quick Start

1. Unpack

Open the box and remove all the pieces from their protective packaging.

2. Charging the WWS150i

You must charge the scanner for 4 hours before first using it. To charge

the scanner, plug the power supply into the bottom of the scanner.

3. Connecting the scanner to a Bluetooth device

The scanner will connect to most Bluetooth devices that support HID

connection.

You will need to open your Bluetooth software and search for Bluetooth

devices. The Bluetooth software can be found by clicking the Bluetooth

symbol on the start bar near the computer time.

QSG

2 3

QSG

In order to configure Wasp WWS150i Freedom Scanner, familiarize

yourself with the setup procedures on the following pages. The default

settings of the scanners are identified on each page and clearly marked

using an asterisk (*). The default settings have been preprogrammed for

the most common barcode configurations. Use the setup & configuration

barcodes only to customize the WWS150i Freedom Scanner settings. If

you need to configure the Scanner, the default settings will be overwritten.

All the programmed settings are stored permanently in non-volatile

memory.

In order to configure Wasp WWS150i Freedom Scanner,

two basic steps need to be followed:

(1) Locate the group that contains the options to be changed.

(2) Scan the barcode representing the option to be changed.

The scanner will sound two beeps.

Setup & Configuration

QSG

Use the Factory Default barcode to reset the scanner to the Default settings.

Factory Default

Check Version

Scan the Check Version barcode to verify your current firmware’s version number.

Check Version

Factory Default

Link Quality affects the transmission quality. When Link Quality is turned

on (default setting), data transfer is more secure, but slower. If you notice

that your transmissions to the host are too slow, you can try turning the

Link Quality setting to off.

Link Quality On/Off

Link Quality On* Link Quality Off

Set Connection

Scan this barcode to break your current connection and enable your device

to connect to a new Bluetooth host.

Set Connection

QSG

Bluetooth SPP (Bluetooth COM)

The Bluetooth SPP (Serial Port Protocol) creates a virtual Bluetooth

comport. This setting is not recommended. Only use this option if you

have software capable of capturing data off of a comport.

Bluetooth SPP (Bluetooth COM)

Bluetooth HID

Use this setting (on by default) to pair with most Bluetooth connections.

Bluetooth HID works just like a keyboard.

Bluetooth HID*

QSG

Terminator

The ‘Terminator’ option is used to specify the end-of-text message and is

primarily used to denote the end of the barcode value.

CR *

None

CR + LF

TAB

Space

ESC

iPad/iPhone Toggle Keyboard

Scan this barcode to display or hide the on-screen keyboard when

connected to an iPad or iPhone.

iPad/iPhone Toggle Keyboard

QSG

connection

Enable/Disable iOS Hotkey

Use these barcodes to enable or disable the iOS hotkey on your device.

When the iOS hotkey is enabled, you can double-click the trigger to toggle

the iPhone/iPad Touch Keyboard.

Enable iOS Hotkey

Disable iOS Hotkey

Wasp®Barcode Technologies

1400 10th Street, Plano, Texas 75074

Tel: 214.547.4100 • Fax: 214.547.4101

www.waspbarcode.com

Other manuals for WWS150i

Table of contents

Wasp WWS150i User manual

Popular Barcode Reader manuals by other brands