VQ Radio Control Model VQA098 User manual
DORNIER
Radio control model
R/C Flugmodell
MONTAGEANLEITUNG
INSTRUCTION MANUAL
SPECIFICATIONS
Wingspan 1210mm.
Length 940mm.
Electric Motor (See next page)
Radio 4 Channel / 4 Servos
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
TECHNISCHE DATEN
Spannweite 1210mm
Lange 940mm
Elektroantrieb (siehe nächste Seite)
Fernsteuerung 4 Kanal / 4 Servos
DO-27
VQ No: VQA090
Designed for brushless electric motors
Entwickelt für Brushless Elektro Motoren
VQ No: VQA099
VQ No: VQA098
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
1.5mm
AB
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
SILICON
EPOXY A
EPOXY B
CA
Epoxy Glue (30 minutes type)
Silicon Glue
Cyanoacrylate Glue
Sekundenkleber
Epoxy-Klebstoff (30min)
Silikonkleber
Tool Required/ Empfohlenes Werkzeug
The pre-covered film on ARF kit may wrinkle due to variations of temperature.
Store model in a cool and dry place for awile.
Then, staring with low heat, you may carefully use a hair dryer to smooth out wrinkels.
Die Bespannung des Modells kann durch Temeratureinflusse erschlaffen oder Falten
werfen z.b bei zu starker Sonnenenstrahlung oder Hitze.
Stellen Sie das Modell zunachst an einen kuhlen Platz fur eine bestimmte Zeit. Danach
konnen Sie versuchen die restlichen Falten vorstichtig mit einem Haartrockner zu behandeln.
!
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
4 - channel radio
RECOMMENDED ACCESSORIES
4 - Kanal
Fernsteuerung
MASTER, No. 5374
Empfohlenes Zubehör
Antrieb Tuning (Kraftvoller Kunstflug):
BOOST 25 Brushless Combo Set, No. C2981
LiPo Akku RED POWER 2200-3S, No. C2158
Propeller 10*5, No. C5749
4 x Servo S2112
mit 500mm Servokabel
Full the elevator out of the
horizontal stabilizer.
Cut away only
the film both side
1A
1B
1
When you are satisfied with the alignment,
use a pencil to trace around the top and
bottom of the stabilizer where it meets the
fuselage.
Cut away only
the covering
both side
BB’
B=B’
Aluminum wing joiner
Remove the horizontal stabilizer from the
fuselage. Using the sharp hobby knife,
carefully cut away the covering inside the
lines which were marked above.
* WARNING: When removing any covering
from the airframe, please ensure that you
secure the cut edge with CA or similar
cement. This will ensure the covering
remain tight.
Stabilizer
AA’
A=A’
Stabilizer
FUSELAGE
Again, Install the horizontal stabilizer into the
fuselage and adust the alignment as described
in steep 1C. Secure the horizontal stabilizer in
place using CA glue.
1C
1D
1E
Elevator connector
Note: do not glue the elevator connector
into the fuselage or stabilizer.
Note: The slots for the control horn
installation are pre- cut at factory.
Control horn
...........2
CA
CA
Thin CA glue
Thin CA glue
Push the elevator and its hinges into the hinge slots in the trailing edge of the
horizontal stabilizer.
There should be a minimal hinge gap.
When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using CA glue.
Hinge STABILIZER
CA
Apply thin CA to both
side of the hinge
Full the rudder out of the
vertical stabilizer.
1F
1G
1H
2
2A 2B
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft
auftreten!
CA
CA
Elevator connector
CA
CA
Apply thin CA to each of the
four joints and use a generous
amount to ensure to strong bond.
Cut away only the covering
both side
Realign the vertical stabilizer, then glue
the vertical stabilizer into the fuselage,
using a generous amount of thin CA.
CA
Thin CA glue
Hinge STABILIZER
CA
Apply thin CA to both
side of the hinge
Push the rudder and its hinges into the hinge slots in the trailing edge of the
horizontal stabilizer. There should be a minimal hinge gap.
When satisfied with the and alignment, hinge the elevator to the horizontal
stabilizer using CA glue.
2D
2E
2F
2G
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft
auftreten!
When you are satisfied with the alignment,
use a pencil to trace around the right and
left of the stabilizer where it meets the
fuselage.
2C
CA
AB
A
A=38mm
2mm
Drill a 2mm diameter hole in torque rod
mounting slot, marking sure that you
drill the hole perpendicular to the leading
edge of the rudder.
2H 25mm tail wheel
2mm collar
Apply thin CA to each of the
joints and use a generous
amount to ensure to strong
bond.
Note: The slots for the control horn
installation pre- cut at factory.
Control horn
...........1
............4
4X20mm screw
3
4A
............2
4X30mm screw
4mm nut-washer
4mm washer
4mm nut
4x30mm screw
Aluminum landing gear
CA
CA
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft auftreten!
4B
4C
4
Pull the magnetic battery hatch
out of the fuselage
55A
5B
! Engine thrust on balk head
is already adjust at factory
Sturz und Zug beachten!
Sperrholztrager Platten zusammenkleben, wie gezeigt ausrichten
und Locher bohren.
Motor nach untenstehendem Schema einbauen.
Fur optimale Leistung empfehlen wir folgende Komponenten:
-Brushless-Motor PICHLER BOOST 60
-Brushless Regler PICHLER XQ-70
-LiPO Akku LEMONRC 3700-5S
-Luftschraube 12*6 - 13*8
For maximum performance, we recommended
the following:
-Brushless-Motor PICHLER BOOST 60
-Brushless Regler PICHLER XQ-70
-LiPO Battery LEMONRC 3700-5S
-Propeller 12*6 - 13*8
5C
FUSELAGE - BOTTOM VIEW
The holes for the elevator servo
are Pre-cut at factory..
Cut away only the covering
66A
1.5mm
2mm
FUSELAGE - BOTTOM VIEW
6B
Elevator linkage
FUSELAGE - BOTTOM VIEW
Rudder linkage
1.5mm
6C
77A
7B
L/R
X
X
BOTTOM - VIEW / Unteransicht
Aileron
extension cord
Plastic control horn
Linkage Stopper set
.....................2
.................2
1.2mm O Alenk-Gestange
Aileron & flap pushrod
Note: The slots for the control
horn installation are pre- cut at
factory.
CA
Vergewissern Sie sich, sauber geklebt zu haben.
Andernfalls konnen Probleme mit der Flugeigenschaft
auftreten!
WARNING! Securely glue together.
If coming off during flights, you lose control
of your airplane which leads to accidents !
8
96x45mm Nylon bolt
......1
6x45mm Nylon bolt
55~58 mm
15mm
8mm
10mm
10mm
Aileron /
Rudder
Elevator /
8mm
15mm
Querruderausschlag
Hohenruderausschlag
Seitenruderausschlag
Do not try to fly an out-of balance model!
Uberprufen Sie vor dem Flug den Schwerpunkt.
IMPORTANT: Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner
to clean on surface of your model to keep the colour not fade.
All details are subject to change
without notice !
Technische Anderungen und Irrtumer
vorbehalten !
CG
10
This manual suits for next models
1
Table of contents
Other VQ Radio Control Model Toy manuals
VQ Radio Control Model
VQ Radio Control Model P-39 Q/N AIRACOBRA Instruction Manual
VQ Radio Control Model
VQ Radio Control Model PICHLER Beechcraft T-34C TURBO MENTOR User manual
VQ Radio Control Model
VQ Radio Control Model FLOAT User manual
VQ Radio Control Model
VQ Radio Control Model Swallow User manual
VQ Radio Control Model
VQ Radio Control Model Bearcat F8F User manual
VQ Radio Control Model
VQ Radio Control Model U.S NAVY F.8F BEARCAT User manual
VQ Radio Control Model
VQ Radio Control Model KA-7 User manual
VQ Radio Control Model
VQ Radio Control Model P-51B Mustang User manual
