Vivotek Supreme FD8362 User manual
EN - 1
English
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Contact your distributor in the event of
occurrence.
Refer to your user's manual for the
operating temperature.
Warning Before Installation
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not insert sharp or tiny objects
into the Network Camera.
Do not drop the Network Camera.
EN - 2
Software CD
FD8362/62E
Quick Installation Guide /
Warranty Card
Alignment Sticker /
Ceiling Hole Template Sticker
Mounting Plate
5
1
0
0
0
0
2
1
0
G
Package Contents
1
L-type Hex Key Wrench / Silica Gel /
Screws / Hex Nut / DC Power Cable /
Double-sided Tape
Waterproof Connector & Bushing DC Power Adapter (Optional, for
indoor use only)
EN - 3
English
Light Sensor
Physical Description
2
Inner View
Ethernet 10/100
RJ45 Socket
Audio/Video
Out (green)
Microphone In
(pink) General I/O Terminal
Block
Operating environment: -40° ~ 55°C
When the temparature inside the Network Camera
drops to 0°C, the heater will operate automatically.
Heater
Vari-focal Lens
Tilt Adjustment Screw
Jumpers
Microphone Video Output
Internal
External
NTSC
60Hz
PAL
50Hz
12
Micro SD/SDHC Card Slot
Reset
Button
Black Cover
NOTE: The heater is only available on
FD8362E.
EN - 4
Outer View
Record the MAC address
under the camera base
before installing the camera.
Replace the side opening cover with the
included side outlet bushing if you want to
route cables from the side of camera. The
1/2" protection conduits and tubing are
separately purchased.
IP66-rated Vandal-proof
Dome Cover Mounting Plate
EN - 5
English
First, use the included T20 hex key wrench to loose the four screws and detach the dome cover from the
camera base. Follow the steps below to install the camera either to a ceiling or a wall.
Hardware Installation
3
Top View
Dome Cover
Dome Cover Retainer
Connect power lines and if you have external devices such as sensors and alarms, make the connection
from the general I/O terminal block.
87654321
Cabling Assembly
Pin Denitions
1 DC 12V-
2 DC 12V+
3 AC 24V_2
4 AC 24V_1
5 DI- (GND)
6 DI+
7 DO-
8 DO+ (12V)
For Ethernet
Cable For Power & IO Cables
Top View
Power and IO cables pass through a waterproof connector. The
Ethernet cable should be routed through a rubber seal plug. All
cables are user-supplied.
IMPORTANT! Dome cover should be removed because if it should fall during the installa-
tion process, physical injury could occur to your co-workers.
The max. output load from pins #7
and 8 is 400mA.
NOTE:
EN - 6
1. Disassemble the components of the waterproof
connector into parts (A) ~ (F) as shown above.
2. Place the screw nut (E) on the Power and GPIO
opening.
3. Feed the power cables through the waterproof
connector (F --> E --> D --> B --> A) as the
illustration shows. Then connect the power
cables to the power source. Note: There are 8
holes on the seal (D), and the widest holes with
a crack on the side are specic for power cables.
4. If you have external devices such as sensors
and alarms, feed the cables through the
Assembling Steps
Sealing Nut (A)
Housing (B)
Seals (C)
Seal (D)
Screw Nut (E)
Hex Nut (F)
Waterproof Connector
(A)
(B)
(D)
(E)
(F)
waterproof connector (F --> E --> D --> B -->
A) as previously described. Refer to the pin
definition to connect them to the general I/O
terminal block. Note: The recommended cable
gauge is 2.0 ~ 2.8 mm.
5. Push the seal (D) into the housing (B).
6. Insert the seals (C) into unused holes on the
seal (D) to avoid moisture.
7. Secure the sealing nut (A) tightly and hex nut
(F) from the bottom of the camera.
1
2
RJ45 Cable Dimension (unit: mm)
2. Strip part of the sheath from the
Ethernet cable.
1. Drill a hole on the rubber seal
plug and insert an Ethernet cable
through the opening.
Rubber Seal
Plug
Assembling Steps
Recommended cable gauge: 24AWG (0.51 mm)
Connecting RJ45 Ethernet Cable
EN - 7
English
4
3
o
O
g
B
b
G
br
BR
1
2
3
4
5
6
7
8
o: white/orange stripe
O: orange solid
g: white/green stripe
B: blue solid
b: white/blue stripe
G: green solid
br: white/brown stripe
BR: brown solid
3. You will need an RJ45 crimping tool to
attach the Ethernet wires to a connector.
When done, connect the cable to the
camera’s Ethernet RJ45 socket.
4. Press the Ethernet cable into the routing path at
the bottom of the camera so that the cable will not
get in the way when the metal mounting plate is
attached.
Ceiling mount
1. Attach the supplied alignment sticker to the ceiling.
2. Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the
ceiling. Then hammer the four supplied plastic anchors into the holes.
3. Through three or four holes on the mounting plate, insert the supplied screws into the corresponding
holes and secure the mounting plate with a screwdriver.
4. Feed the cables through the triangular cutout A or side opening B. If you want to use hole B, remove
the side cover using a screwdriver. Secure the camera base to the mounting plate with three supplied
screws.
5. Remove the black cover.
1
4
A
B
5
2
3
Black Cover
EN - 8
1
2
3
A
4
B
5
Wall mount
1. Attach the supplied alignment sticker to the wall.
2. Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the
wall. Then hammer the four supplied plastic anchors into the holes.
3. Through three or four holes on the mounting plate, insert the supplied screws into the corresponding
holes and secure the mounting plate with a screwdriver.
4. Feed the cables through the triangular cutout A or side opening B. If you want to use hole B, remove
the side cover using a screwdriver. Secure the camera base to the mounting plate with three supplied
screws.
5. Remove the black cover.
Black Cover
EN - 9
English
Power over Ethernet (PoE)
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
PoE Switch
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via a single Eth-
ernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch
via Ethernet cable.
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
Network Deployment
4
1. Connect RJ45 Ethernet cable to a switch.
Use a Category 5 Cross Cable when your
network camera is directly connected to PC.
2. Connect either the DC or AC cables from
the terminal block. The IO cables are user-
supplied.
Ethernet
Non-PoE Switch
Pin 1
Pin 2
Pin 3
Pin 4
DC 12V
AC 24V±10%
Black
Red
General Connection (without PoE)
1. This equipment is only to be connected to PoE
networks without routing to outside plants.
2. For PoE input connections, use only UL listed I.T.E.
with PoE output.
NOTE:
1. The DC power adaptor, if used, should
comply with: O/P: 12V DC, 1.5A min.,
L.P.S. certied.
2. Pin #3 & 4 AC 24V as alternate power are
for indoor use only
NOTE:
Other manuals for Supreme FD8362
2
This manual suits for next models
1
Table of contents
Other Vivotek Security Camera manuals
Vivotek
Vivotek IP7361 User manual
Vivotek
Vivotek CC9381-HV User manual
Vivotek
Vivotek IP8371E User manual
Vivotek
Vivotek IP6114 User manual
Vivotek
Vivotek FD9366-HV User manual
Vivotek
Vivotek FE8174V User manual
Vivotek
Vivotek FE9380-HV User manual
Vivotek
Vivotek C Series User manual
Vivotek
Vivotek FE8181 User manual
Vivotek
Vivotek PZ7151 User manual
Vivotek
Vivotek IP8330 User manual
Vivotek
Vivotek IP8162P User manual
Vivotek
Vivotek VORTEX FE912-H User manual
Vivotek
Vivotek IP8161 User manual
Vivotek
Vivotek FD8181 User manual
Vivotek
Vivotek FD816C-HF2 User manual
Vivotek
Vivotek FD9371-HTV User manual
Vivotek
Vivotek IP7137 User manual
Vivotek
Vivotek IP8132 User manual
Vivotek
Vivotek PT3114 User manual
