Vivotek IP8335H User manual
This guide describes the basic functions of IP8335H. More
details can be found in the User Manual.
IP Surveillance
P/N: 625015800G Ver.1.0
Copyright 2011 VIVOTEK INC. All right reserved.
New Taipei City
Quick Installation Guide
English 繁中 日本語 Español Português
簡中 Français Deutsch Italiano Türkçe Polski Русский Česky Svenska
720p HD WDR Pro IP67
IP8335H
EN-1
English
Warning Before Installation
Contact your distributor in the
event of occurrence.
Refer to your user's manual for the
operating temperature.
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Do not touch the Network Camera
during a lightning storm.
Do not place the Network Camera on
unsteady surfaces.
Do not drop the Network Camera.
Do not insert sharp or tiny objects
into the Network Camera.
EN-2
Package Contents
1
5
1
0
0
0
0
2
0
2
G
Software CD
IP8335H
Quick Installation Guide /
Warranty Card
Waterproof Connector (for backup
use)
Alignment Sticker
Wall Mount Bracket
Sun Shield
Wrench / RJ45 Female/Female Coupler / Double-sided Tape / Screws
Power Adapter
Moisture Absorber
EN-3
English
Physical Description
2
IR LED
Lens
Light Sensor
General I/O
Terminal Block
Zoom Controller
Focus Controller
Reset Button
Alternate AC Power Source
Ethernet 10/100
RJ45 Plug
Power Cord Socket
+ AC 24V +
- AC 24V -
Micrso SD/SDHC
Card Slot
EN-4
1
2
5
4
3
6
5
4
6
1. Attach the alignment sticker to the wall. Drill three holes into the wall. Then hammer the supplied
plastic anchors into the holes and secure the plate with supplied screws.
2. Feed the cables through the front opening of the wall mount bracket. (If you want to use external
devices such as sensors and alarms, please refer to the assembling steps on the next page.)
3. Hang the wall mount bracket on the plate.
4. Fix the Network Camera on the wall mount bracket with two screws on both sides.
5. Secure the wall mount bracket with the supplied screws.
6. Adjust the angle of the wall mount bracket to aim at the shooting area.
Hardware Installation
3
The supplied L-type hex key wrenches are exclusively
designed to match each screw. In case you will need to adjust
the lens later, do not discard the wrenches.
IMPORTANT!
EN-5
English
Waterproof Connector
1 N/C
2 N/C
3 DO- *
4 DO+ **
5 Digital Input: - (Ground)
6 Digital Input 3: DI3
7 Digital Input: - (Ground)
8 Digital Input 2: DI2
87654321
J3
J7
87654321
Components of the Waterproof Connector
Seals (D)
Housing (E)
Sealing Nut (F)
Seal (C)
Screw Nut (B)
Pin Denitions
Rubber (A)
J7
1 Digital Input 1: DI1
2 Digital Input: - (Ground)
3 RS485 +
4 RS485 -
5 AUDIO_GND
6 AUDIO_IN: Ext_MIC_IN
7 AUDIO_GND
8 AUDIO_OUT
J3
* Vmax.: 40V DC, Imax.: 400mA.
** Power output, 12V DC: max. load is 50mA.
The terminal block is accessible when the rear cover is opened.
Power
PCB
Micro SD Socket
Ethernet
EN-6
1. Disassemble the components of the waterproof connector into part (A) ~ (F) as shown above.
2. Remove the rubber stopper from the bottom of the Network Camera and secure the rubber (A)
and screw nut (B) tightly.
3. Open the back cover of the Network Camera.
4. If you have external devices such as sensors and alarms, feed the cables through the waterproof
connector (F --> E --> C --> A+B) as the illustration shown below. Then refer to the pin denition
to connect them to the general I/O terminal block. Note: The recommended cable gauge is 2.0 ~ 2.8
mm.
5. Push the seal (C) into the housing (E).
6. Insert the seals (D) into the empty holes on the seal (C) to avoid moisture.
7. Secure the sealing nut (F) tightly.
8. Tighten the back cover.
9. Remove rubber (G) and feed the cables through the wall mount bracket.
Assembling Steps
(A)+(B)
2
6
(E)
(C)
(F)
(D)
(C)
4
7
(E)
(F)
3
(C)
5
8
9
(F)
(G)
EN-7
English
Network Deployment
4
Power over Ethernet (PoE)
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE
switch.
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via a single
Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled
switch via Ethernet cable.
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
Non-PoE Switch
PoE Power Injector
(optional)
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
PoE Switch
RJ45 Female/
Female Coupler
EN-8
1. Install "Installation Wizard 2" from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network
is analyzed, please click on the "Next" button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches
the one on the product label to connect to the Network Camera via Internet Explorer.
Network Camera
Model No: IP8335H
Made in Taiwan
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Pat. 6,930,709
MAC:0002D1730202
R o H S
0002D1730202
00-02-D1-73-02-02 192.168.5.151 IP8335H
Installation
Wizard 2
IW
2
Assigning an IP Address
5
EN-9
English
For further setup, please refer to the user's manual on the software CD.
Ready to Use
6
1. Access the Network Camera from the LAN.
2. Retrieve live video through a web browser or recording software.
3. Unscrew the zoom controller to adjust the
zoom factor. Upon completion, tighten the
zoom controller.
4. Unscrew the focus controller to adjust the
focus range. Upon completion, tighten the
focus controller.
T
W
∞
N
3
4
Other manuals for IP8335H
3
Table of contents
Other Vivotek Security Camera manuals
Vivotek
Vivotek FD8361L User manual
Vivotek
Vivotek IZ7151 User manual
Vivotek
Vivotek PZ7112 User manual
Vivotek
Vivotek PT3113 User manual
Vivotek
Vivotek PZ7151 User manual
Vivotek
Vivotek FD9369 User manual
Vivotek
Vivotek IP8355H User manual
Vivotek
Vivotek FE8172V User manual
Vivotek
Vivotek Supreme IP9165-HT-v2 User manual
Vivotek
Vivotek IP7161 User manual
Vivotek
Vivotek IP8355EH User manual
Vivotek
Vivotek PZ8111 User manual
Vivotek
Vivotek Supreme FD8363 User manual
Vivotek
Vivotek CC9381-HV User manual
Vivotek
Vivotek PZ7111 User manual
Vivotek
Vivotek FD8177-H User manual
Vivotek
Vivotek FD8164 User manual
Vivotek
Vivotek IP8371E User manual
Vivotek
Vivotek IP8161 User manual
Vivotek
Vivotek FD8171 User manual
