Vivotek FE8171V User manual
P/N: 625015100G Ver.1.0
Copyright 2011 VIVOTEK INC. All rights reserved.
c
FE8171V
3MP‧360° Panoramic View‧Vandal-proof
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, Taiwan | T: +886-2-82455282 | F: +886-2-82455532 | E: [email protected]
EN - 1
English
Contact your distributor in the event of
occurrence.
Warning Before Installation
Power off the Network Camera
as soon as smoke or unusual
odors are detected.
Do not place the Network
Camera on unsteady surfaces.
Do not insert sharp or tiny
objects into the Network
Camera.
Refer to your user's manual
for the operating temperature.
Do not touch the Network
Camera during a lightning
storm.
Do not drop the Network
Camera.
EN - 2
Package Contents
1
5
1
0
0
0
0
2
1
0
G
FE8171V Mounting Plate / Screwdriver
Alignment Stickers Screws / Moisture Absorber /
Double-sided Tape / Rubber Seal
Plug / Rubber Washer
Quick Installation Guide /
Warranty Card
Software CD
Power & I/O Cables DC Power Adapter
For Mounting Plate For Camera Base
EN - 3
English
Physical Description
2
Inner View
Pin Header (J7)
Spring Contacts
(A)
Lens
Contacts for Internal Microphone
(B)
Pin Header (J6)
Ethernet 10/100 RJ45 Socket
i
Align (B) to (A) when
attaching the dome
cover
MicroSD/SDHC/SDXC Card Slot
Reset Button
EN - 4
Network Camera
Model No: FE8171V
MAC: 0002D1XXXXXX
Pat. 6,930,709
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Made in Taiwan
Outer View
Built-in Microphone
IP66-rated
Vandal-proof
Dome Cover
IMPORTANT!
Record the MAC address
under the camera base before
installing the camera.
EN - 5
English
Hardware Installation
3
Dome Cover Retainer
Rubber Stopper on
the hole for Power &
IO Cables
Tamper-proof Screw
Rubber Seal Plug
on the hole for RJ45
Ethernet Cable
i
Connect the supplied power
& IO cables if your switch
does not support PoE.
First, use the supplied screwdriver to loose the four screws and detach the dome cover from the
camera base. Then, follow the steps below to install the camera to either a ceiling or a wall.
EN - 6
RJ45 Cable Dimension (unit: mm)
Assembling Steps
2. Strip part of the sheath from the Ethernet
cable.
1. Drill a hole on the rubber seal plug and
insert an Ethernet cable through the open-
ing.
3. You will need an RJ45 crimping tool to
attach the Ethernet wires to a connec-
tor. When done, connect the cable to the
camera’s Ethernet RJ45 socket.
Recommended cable gauge: 24AWG (0.51 mm)
Connecting RJ45 Ethernet Cable
Connecting DC Power Cable
Rubber Seal
Plug
1
2
o
O
g
B
b
G
br
BR
1
2
3
4
5
6
7
8
3
44. Remove the original black seal plug from the camera base. Then
feed the Ethernet cable from the bottom of the camera and through
the hole. Attach the rubber seal plug for water proong.
1. Remove the rubber stopper from the camera base.
2. Add the supplied rubber washer to the cable as shown in the picture.
3. Feed the cable from the bottom of the camera and tighten the plastic base for waterproong.
o: white/orange stripe
O: orange solid
g: white/green stripe
B: blue solid
b: white/blue stripe
G: green solid
br: white/brown stripe
BR: brown solid
EN - 7
English
Ceiling/Wall Mount without Mounting Plate
(Choose this mounting type if you would like to feed the cables form the bottom
of the camera)
NOTE:
Arrange the cables neatly to avoid
getting in the way when the dome
cover is attached.
Pin Header (J7)
Pin Header (J6)
123
89
4
5
6
1. Attach the supplied alignment sticker for camera base to the ceiling/wall.
2. Using the three circles on the sticker, drill three pilot holes into the ceiling. Then hammer the
three supplied plastic anchors into the holes.
3. Drill a cable hole on the ceiling/wall, and feed the cables through the hole.
4. Connect the Ethernet cable to the socket.
5. Connect the two white pin header connectors to the J6 and J7 connectors.
6. Secure the camera base to the ceiling/wall with three supplied screws.
7. You will nd a moisture absorber attached to the camera. Replace the moisture absorber includ-
ed in the camera with the one shipped within the accessory bag.
8. Attach the dome cover.
9. Secure the four screws with the supplied stardriver. Make sure all camera parts are securely in-
stalled.
EN - 8
Ceiling/Wall Mount with Mounting Plate
(Choose this mounting type if you would like to feed the cables form the side)
1
2
3
4
7
9
10
7-1
7-2
1. Attach the supplied alignment sticker for the supplied mounting plate to the ceiling/wall.
2. Using the three circles on the sticker, drill three holes into the ceiling. Then hammer the three
supplied plastic anchors into the holes.
3. Arrange and feed the cables through the side of the mounting plate.
4. Secure the mounting plate to the ceiling/wall with three supplied screws.
5. Connect the Ethernet cable to the socket.
6. Connect two white pin header connectors to the J6 and J7 connectors.
7. Attach the camera base to the mounting plate and turn counter-clockwise as shown below
(Figure 7-1). Then secure the supplied screws to x the camera base.
8. You will nd a moisture absorber attached to the camera. Replace the moisture absorber with
the one shipped within the accessory bag.
9. Attach the dome cover.
10. Secure the four screws with the supplied stardriver. Make sure all camera parts are securely
installed.
EN - 9
English
1. Connect RJ45 Ethernet cable to a switch. Use a Category 5 Cross Cable when your network
camera is directly connected to PC.
2. Connect the power cable from the Network Camera to a power outlet.
3. If you have external devices such as sensors and alarms, make the connection from the general
I/O terminal block.
General Connection (without PoE)
Network Deployment
4
+3V3
DO
D1
GND
POWER C
OLLIS
ION
LINK
RECEI VE
PART I TI O N
12345
1
2
3
General I/O Terminal Block
Power Cord Socket (Black)
Microphone In (Pink)
Audio Out (Green)
+3V3: Power, 3.3V DC
DO: Digital Output
D I: Digital Input
GND: Ground
Other manuals for FE8171V
4
Table of contents
Other Vivotek Security Camera manuals
Vivotek
Vivotek WDR Pro II User manual
Vivotek
Vivotek IB836B-H(R)T User manual
Vivotek
Vivotek FD8166 User manual
Vivotek
Vivotek FD9165-HT-A User manual
Vivotek
Vivotek FD8365EHV User manual
Vivotek
Vivotek Supreme SD8363E User manual
Vivotek
Vivotek FD8136 User manual
Vivotek
Vivotek IP8332-C User manual
Vivotek
Vivotek IP816A-LPC-18 User manual
Vivotek
Vivotek FD8133V User manual
Vivotek
Vivotek IB9360-H User manual
Vivotek
Vivotek IZ7151 User manual
Vivotek
Vivotek FD8135H User manual
Vivotek
Vivotek FE8191 User manual
Vivotek
Vivotek FD7132 User manual
Vivotek
Vivotek IP7253 User manual
Vivotek
Vivotek FD7141 User manual
Vivotek
Vivotek FD8134 Operator's manual
Vivotek
Vivotek FD8166 User manual
Vivotek
Vivotek 2M User manual
