Vivotek FD8335H User manual
EN - 1
English
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Contact your distributor in the event of
occurrence.
Refer to your user's manual for the
operating temperature.
Warning Before Installation
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not insert sharp or tiny objects
into the Network Camera.
Do not drop the Network Camera.
EN - 2
Software CD
FD8335H
Quick Installation Guide /
Warranty Card
Alignment Sticker /
Ceiling Hole Template Sticker
Mounting Plate
5
1
0
0
0
0
2
2
1
G
Package Contents
1
L-type Hex Key Wrench / Moisture
Absorber / Screws / Hex Nut / Double-
sided Tape / AV Cable
Waterproof Connector & Bushing
EN - 3
English
IR LEDs (18 units, effective up
to 15m)
Physical Description
2
Inner View Lens
Tilt Adjustment Screw
Black Cover
1. There is no internal microphone. Only external microphone is applicable.
2. The Focus Assist button takes effect when using a hand-held monitor or camera
tester with a BNC connector. Press the button and use the focus and zoom
adjustment pullers to tune the image until the "BEST FOCUS" message is
shown.
Ethernet 10/100
RJ45 Socket
Audio/Video
Out (green)
Microphone In
(pink) General I/O Terminal
Block
Jumpers
Microphone Video Output
Internal
External
NTSC
60Hz
PAL
50Hz
12
Micro SD/SDHC Card Slot
Reset
Button
Focus Assist Button
LCD Monitor/
Camera tester
AV Out
Focus Assist
Button
EN - 4
First, use the included T20 hex key wrench to loose the four screws and detach the dome cover from the
camera base. Follow the steps below to install the camera either to a ceiling or a wall.
Hardware Installation
3
Top View Dome Cover
Dome Cover Retainer
IMPORTANT! Dome cover should be removed because if it should fall during the installation
process, physical injury could occur to your co-workers.
Record the MAC address
under the camera base
before installing the camera.
Replace the side opening cover with the
included side outlet bushing if you want to
route cables from the side of camera. The 1/2"
protection conduits and tubing are separately
purchased.
EN - 5
English
Connect power lines and if you have external devices such as sensors and alarms, make the connection
from the general I/O terminal block.
87654321
Cabling Assembly
Pin Denitions
1 AC24V_2
2 AC24V_1
3 DI3+
4 DI2+
5 DI1+
6 DI-
7 DO-
8 DO+ (12V)
For Ethernet
Cable For Power & IO Cables
Top View
Power and IO cables pass through a waterproof connector. The
Ethernet cable should be routed through a rubber seal plug. All
cables are user-supplied.
1. Disassemble the components of the waterproof
connector into parts (A) ~ (F) as shown above.
2. Place the screw nut (E) on the Power and GPIO
opening.
3. Feed the power cables through the waterproof
connector (F --> E --> D --> B --> A) as the
illustration shows. Then connect the power
cables to the power source. Note: There are 8
holes on the seal (D), and the widest holes with
a crack on the side are specic for power cables.
4. If you have external devices such as sensors
and alarms, feed the cables through the
Assembling Steps
Sealing Nut (A)
Housing (B)
Seals (C)
Seal (D)
Screw Nut (E)
Hex Nut (F)
Waterproof Connector (A)
(B)
(D)
(E)
(F)
waterproof connector (F --> E --> D --> B -->
A) as previously described. Refer to the pin
definition to connect them to the general I/O
terminal block. Note: The recommended cable
gauge is 2.0 ~ 2.8 mm.
5. Push the seal (D) into the housing (B).
6. Insert the seals (C) into unused holes on the
seal (D) to avoid moisture.
7. Secure the sealing nut (A) tightly and hex nut
(F) from the bottom of the camera.
EN - 6
1
2
RJ45 Cable Dimension (unit: mm)
2. Strip part of the sheath from the
Ethernet cable.
1. Drill a hole on the rubber seal
plug and insert an Ethernet cable
through the opening.
Rubber Seal
Plug
Assembling Steps
Recommended cable gauge: 24AWG (0.51 mm)
Connecting RJ45 Ethernet Cable
4
3
o
O
g
B
b
G
br
BR
1
2
3
4
5
6
7
8
o: white/orange stripe
O: orange solid
g: white/green stripe
B: blue solid
b: white/blue stripe
G: green solid
br: white/brown stripe
BR: brown solid
3. You will need an RJ45 crimping tool to
attach the Ethernet wires to a connector.
When done, connect the cable to the
camera’s Ethernet RJ45 socket.
4. Press the Ethernet cable into the routing path at
the bottom of the camera so that the cable will not
get in the way when the metal mounting plate is
attached.
EN - 7
English
1
2
3
A
4
B
5
Wall mount
1. Attach the supplied alignment sticker to the wall.
2. Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the
wall. Then hammer the four supplied plastic anchors into the holes.
3. Through three or four holes on the mounting plate, insert the supplied screws into the corresponding
holes and secure the mounting plate with a screwdriver.
4. Feed the cables through the triangular cutout A or side opening B. If you want to use hole B, remove
the side cover using a screwdriver. Secure the camera base to the mounting plate with three supplied
screws.
5. Remove the black cover.
Black Cover
EN - 8
POWER C
OLLIS
ION
LINK
RE
CEIVE
PARTITION
12345
Network Deployment
4
1. Connect RJ45 Ethernet cable to a switch.
Use a Category 5 Cross Cable when your
network camera is directly connected to PC.
2. Connect the AC cables from the terminal
block as an alternate power source. The IO
cables are user-supplied.
Ethernet
Non-PoE Switch
Pin 1
Pin 2
AC 24V±10%
Black
Red
General Connection (without PoE)
Ceiling mount
1. Attach the supplied alignment sticker to the ceiling.
2. Using the circle marks on the sticker, drill at least 2 pilot holes symmetrically on each side into the
ceiling. Then hammer the four supplied plastic anchors into the holes.
3. Through three or four holes on the mounting plate, insert the supplied screws into the corresponding
holes and secure the mounting plate with a screwdriver.
4. Feed the cables through the triangular cutout A or side opening B. If you want to use hole B, remove
the side cover using a screwdriver. Secure the camera base to the mounting plate with three supplied
screws.
5. Remove the black cover.
1
A
B
5
2
3
4
Black Cover
EN - 9
English
Power over Ethernet (PoE)
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
PoE Switch
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via a single Eth-
ernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch
via Ethernet cable.
POWER COLLISION
LINK
RECEIVE
PARTITION
12345
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE
switch.
PoE Power Injector
(optional)
Non-PoE Switch
Other manuals for FD8335H
2
Table of contents
Other Vivotek Security Camera manuals
Vivotek
Vivotek SD9365-EHL User manual
Vivotek
Vivotek AB5396A User manual
Vivotek
Vivotek SF8174 User manual
Vivotek
Vivotek IP7361 User manual
Vivotek
Vivotek FD8164 User manual
Vivotek
Vivotek FD8166 User manual
Vivotek
Vivotek IP7160 User manual
Vivotek
Vivotek SD8161 User manual
Vivotek
Vivotek FE8171V User manual
Vivotek
Vivotek FE9182-H User manual
Vivotek
Vivotek IP8362 User manual
Vivotek
Vivotek PZ7151 User manual
Vivotek
Vivotek CC8370-HV User manual
Vivotek
Vivotek IP6114 User manual
Vivotek
Vivotek AM-221 User manual
Vivotek
Vivotek 3GPP User manual
Vivotek
Vivotek FD8154 User manual
Vivotek
Vivotek IP3133 User manual
Vivotek
Vivotek SUPREME MD9582-H User manual
Vivotek
Vivotek IP8330 User manual
