Vivo STAND-TS38B/BW User manual

Table of contents

Popular Rack & Stand manuals by other brands

Salamander

Salamander Acadia AC/W/L400/WH Assembly instructions

Fohhn

Fohhn VAT-09 Mounting instruction

ricoo

ricoo FS0522 quick start guide

AMSOIL

AMSOIL BMK-22 Installation and service instructions

Kargo Master

Kargo Master 48220 installation guide

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 installation instructions

ricoo

ricoo S1222 installation instructions

Ready-Set-Mount

Ready-Set-Mount RSMCM602 instruction manual

VidaBox

VidaBox VB MNT FFS2 installation guide

Welch Allyn

Welch Allyn 48960 Assembly instructions

Arkon

Arkon CM035-ST-2 installation instructions

PROEL

PROEL PLWIN60C user manual

Agilent Technologies

Agilent Technologies E2609B installation guide

Mustang

Mustang MV-ARM4 installation guide

Mounting Solutions

Mounting Solutions WRM-320 manual

Pyle

Pyle PMKSPAD1 manual

ShelterIt

ShelterIt 21208 installation instructions

SPL

SPL RackPack?4 1040 manual 

Dual Monitor Desk Stand

Scan the QR code with your mobile device or follow the link

for helpful videos and specifications related to this product.

Instruction Manual

https://vivo-us.com/products/stand-ts38b

SKU: STAND-TS38B/BW

[email protected]om www.vivo-us.com 309-278-5303

Chat live with an agent!

GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2

PACKAGE CONTENTS

WARNING!

A (x1)

Pole

B(x1)

Base

C(x1)

Swivel Arm

If you do not understand these directions, or if you have any doubts about the safety of the

installation, please call a qualified technician. Check carefully to make sure there are no missing or

defective parts. Improper installation may cause damage or serious injury. Do not use this product

for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.

We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or

inappropriate use.

D(x2)

VESA Plate

WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

S-B (x2)

Security Nut

F (x1)

Pole Cable Clip

M-A (x8)

M4x12mm

Thumbscrew

M-B (x8)

M4x30mm

Screw

M-C (x8)

M4 Spacer

TIPOVER WARNING

SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:

• TO PREVENT TIPPING, PLEASE BE CAREFUL NOT TO EXTEND THE ARMS TOO FAR FORWARD

OR BACKWARD.

• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR

STAND.

• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL

USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.

NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED

S-A (x3)

M5x16mm

Flathead

Screw

E(x2)

Arm Cable Clip

T-A (x1)

3mm Allen

Wrench

T-B (x1)

5mm Allen

Wrench

T-C (x1)

6mm Allen

Wrench

3

ASSEMBLY STEPS

STEP 1

Install Pole (A) to Base (B) using M5x16mm Flathead Screw (S-A) and 3mm Allen Wrench (T-A).

TOOLS NEEDED

Phillips

Screwdriver

22 lbs

(10kg)

DO NOT EXCEED WEIGHT CAPACITY.

Failure to do so may result in serious injury.

T-A

S-A

A

B

PER ARM

4

STEP 2

Flat Back Monitor

Attach VESA Plates (D) to the monitors using M4x12mm Thumbscrews (M-A).

NOTE: Hand tighten screws to avoid stripping the plastic screw heads.

STEP 3 (Option A)

Slide Pole Cable Clip (F) and Swivel Arm (C) onto Pole (A) and tighten with 6mm Allen Wrench (T-C).

Assemble Arm Cable Clips (E) to Swivel Arm (C).

M-A

D

A

F

T-C

C

E

5

STEP 3 (Option B)

STEP 4

Curved Back Monitor

Attach VESA Plates (D) to the monitors using M4 Spacers (M-C) and M4x30mm Screws (M-B). Tighten

with a Phillips screwdriver.

Slide the monitors with VESA Plates (D) onto the heads of Swivel Arm (C) and install Security Nuts (S-B).

Make sure Security Nuts (S-B) are installed before you rotate the monitors.

M-C

M-B

D

S-B

D

C

6

STEP 5

Tighten the bolt on the side of the tilt joint using 5mm Allen Wrench (T-B) to fix the tilt angle.

To level the monitors, remove the security nut and turn the bolt with 3mm Allen Wrench (T-A) to raise

or lower the monitor. Replace nut aer the adjustment.

T-B

T-A

7

STEP 6

Use 3mm Allen Wrench (T-A) to adjust joints if needed.

T-A

G

Manage cables and store Allen Wrenches in Pole Cable Clip (G) for future use.

LAST UPDATED: 11/07/2022

REV1.1

Open Monday - Friday 7:00am - 7:00pm CST,

our dedicated support team can oer immediate assistance with rapid response times. If any

parts are received damaged or defective, please contact us. We are happy to replace parts to

ensure you have a fully functioning product.

FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com

Love your new VIVO setup and want to share?

Tag us in your photo! @vivo_us

[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M

- 23% within < 15m

- 38% within < 30m

- 61% within < 1hr

- 83% within < 2hr

- 92% within < 3hr

AVG. RESOLUTION TIME (within oice hrs): < 15 M

www.vivo-us.com

Chat live with an agent!

AVG. RESOLUTION TIME (within oice hrs): 5M 4S

309-278-5303