Vinten Vision 250 Manual

Vinten

Camera Control Solutions

Operators Guide

Vision 250

Pan & Tilt Head

Vision 250

Pan and Tilt Head

Publication Part No. 3525-8 Issue 3

or reproduced in any way including, but not limited to, photocopy, photograph, magnetic or other record without the prior

agreement and permission in writing of

Vinten Broadcast Limited.

Vinten, QuickFit and Vision are registered trademarks of Vinten Broadcast Limited.

Safety - read this first

Warning Symbols in this Operators Guide

Where there is a risk of personal injury, injury to others, or damage to the pan

and tilt head or associated equipment, comments appear, highlighted by the

word WARNING! and supported by the warning triangle symbol.

Technical data

Weight

Flat base (complete with pan bar) 6.05 kg (13.3 lb)

Ball base (complete with pan bar and bowl clamp) 6.39 kg (14 lb)

Height to mounting face

Flat base 184 mm (7.24 in.)

Ball base 171 mm (6.73 in.)

Length 159 mm (6.23 in.)

Width 244 mm (9.6 in.)

Typical payload 25 kg (55 lb) - See balance graph)

Tilt range ±90°

Pan range 360°

Pedestal/tripod fixing 100/150 mm ball

Four-hole flat base

Further information

For further information or advice regarding this pan and tilt head, please contact Vinten Broadcast

Limited, your local Vinten distributor or visit our website.

For full details on maintenance and spare parts, please refer to the Vision 250 Pan and Tilt Head

Maintenance Manual and Illustrated Parts List (Publication Part No. 3465-9), obtainable from Vint-

en Broadcast Limited or your local Vinten distributor. For information on-line, visit our website at

www.vinten.com.

Contents

Page

Safety - read this first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Technical data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Further information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Operation

Installing the head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Mounting the camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Mounting the camera (optional Quickfit adaptor). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Balancing the head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Locking the platform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Pan and tilt brakes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Pan and tilt drag. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Servicing

Routine maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Battery replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Balance mechanism digital display calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Converting the base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Associated publication

Vision 250 Pan and Tilt Head

Maintenance Manual

Publication Part No. 3465-9

(1) Camera mounting screws

(2) Balance knob

(3) Centre lock

(4) Illuminated level bubble

(5) Ambient light level sensor

(6) Digital display

(7) Flat base

(8) Pan bar mounting

(9) Switch for illuminated level bubble, drag knob scales and digital display

(10) Tilt drag adjustment knob

(11) Pan brake lever

(12) Tilt brake lever

(13) Slide lock release

(14) Slide plate

Vision 250 (Left-Hand Side with Flat Base)

(1)(14)

(2)

(3)

(4)

(11)

(7)(10) (9) (5)(6)

(13)

(12)

(8)

(15) Slide plate clamp

(16) Battery cover

(17) Spherical base

(18) Bowl clamp

(19) Pan drag adjustment knob

(20) Telescopic pan bar

Vision 250 (Right-Hand Side with Spherical Base)

(15)

(16)(19)

(17)(18)

(20)

Introduction

The Vision 250 pan and tilt head embodies an adjustable spring counterbalancing mechanism,

thin film (TF) drag assemblies for pan and tilt motions and an adjustable camera mounting plate.

The balance system is easily adjusted by a knob (2) on the rear of the head. Maximum and mini-

mum payloads that can be balanced, and tilt ranges, are depend-ent on the weight of the camera

and accessories and on the centre of gravity (C of G) height.

ThegraphshowstherangeofloadandC ofG height thatcan be maintainedin balance.Theshad-

ed area of graph corresponds to those load/C of G combinations that can be balanced over the

full tilt range. The area to the right indicate the progressively reducing tilt range with greater load

and higher

C of G.

Where a load/C of G combination falls outside of the graph it will be necessary to increase or de-

crease the weight or the C of G height - if possible - to enable the head to balance the load.

Balance graph

14 16 18 20

410 12

2 6 8

8200

in. mm

±90°

±60°

22 24 34 36

15 20 25 30 35 40 45 50 55 60 lb

kg26 28 30 32 38 40 42

65 70 75 80 85 90

190

180

170

160

150

140

130

120

110

100

A digital display (6) indicates the setting of the balance mechanism on a scale of 00 - HI. The dis-

play is illuminated by pressing the switch (9) and extinguishes automatically approximately 15

seconds after adjustments are complete. The same switch also illuminates the level bubble (4)

and the scales of the pan and tilt drag knobs (19)(10). A sensor (5) automatically compensates for

ambient light levels and dims the display. If the ambient light level is high, the level bubble and

drag knob scales will not be lit. The battery forthe system is housed in a compartment in the base

of the head, closed by a cover (16).

Both the pan and tilt mechanisms incorporate the Vinten thin film (TF) system to ensure smooth

movement of the camera about these axes and are fitted with control knobs (19)(10) to adjust the

drag setting. The whip-pan facility is unaffected by the pan drag setting. Both drag knobs are pro-

vided with scales illuminated by the switch (9).

Friction brakes on each axis allow the head to be locked at any chosen position. The operating

levers for both brakes (11)(12) are fitted on the left-hand side of the head.

A centre lock (3) allows the head to be locked in the horizontal position.

A level bubble (4), illuminated by pressing the switch (9), is fitted to the rear of the head.

Pan bar mounting points (8) are located at the rear of the head, on either side of the camera

mounting platform. A telescopic pan bar (20) is supplied and is attached using a pan bar clamp,

with angular adjustment available on the mount serrations. A second pan bar may be fitted.

Two versions of the head are available. One uses a dual 100/150 mm ball mount (17) with a bowl

clamp (18). The other has a flat base (7), with `Quickfix'®and standard four-hole fixing. Mounting

bolts, washers and a spanner are also provided.

The camera is attached to the head by means of a slide plate (14) or by using the optionalQuickfit®

adaptor. A clamp (15) is provided to hold the slide plate in position and a lock (13) prevents its

inadvertent removal from the head.

Operation

Installing the head

The Vision 250 head is supplied with a dual 100/150 mm ball base and is designed for installation

on a compatible Vinten Vision tripod.

The head is also available with a flat base, with `Quickfix' and standard four-hole fixing.

Adaptors are available which enable the heads to be installed on tripods or pedestals fitted with

other mountings. These are listed under ‘Optional Accessories’.

To install a head with a ball mount, remove the bowl clamp assembly (18) from the head, position

the head on the tripod and refit the bowl clamp assembly from below. Level the head with the aid

ofthelevelbubble(4)andtightenthebowlclamp.Thelevelbubblemaybeilluminatedby pressing

the switch (9).The light will extinguish after 15 seconds.

The flat based head may be installed on a tripod or pedestal using the four mounting bolts and

washers provided or by using a `Quickfix' adaptor.

Mounting the camera

Remove the slide plate (14) from the head by releasing the slide plate clamp (15), pressing the

slide lock release (13) and pulling the plate to the rear.

Attach the slide plate to the camera or camera mounting plate under the approximate centre of

the camera's weight using both camera mounting screws (1). Position the screws as far apart as

possible.

Set the platform level and engage the centre lock (3).

Push the slide plate and camera into the platform from the rear, ensuring slide lock release (13)

snaps into position.

NOTE: If the ambient light level is high, the level bubble will not be lit.

Mounting the camera (optional Quickfit adaptor)

If not already attached, secure the Quickfit adaptor (23) to the slide plate (14) with the two screws

provided (1).

Free the Quickfit wedge (22) from the adaptor by simultaneously pushing in the safety catch (25)

and operating the wedge release (24).

Fit the Quickfit wedge (22) to the camera with the two screws provided (21).

Set the platform level and engage the centre lock (3).

Insert the forward end of the wedge into the forward end of the adaptor. Lower the rear of the

wedge into the adaptor until an audible click indicates that the wedge is locked.

Mounting the camera (optional Quickfit adaptor)

(21)

(22)

(23)

(24)

(25)

(1)

(14)

(3)

Other manuals for Vision 250

Table of contents

Other Vinten Camera Accessories manuals

Vinten

Vinten Quattro SL User manual

Vinten

Vinten Vision 6 User manual

Vinten

Vinten Vision 3AS Manual

Vinten

Vinten vector 430 Manual

Vinten

Vinten Vision Blue User manual

Vinten

Vinten Vision 11 User manual

Vinten

Vinten pro-touch Pro-10 System User manual

Vinten

Vinten Vision 250E User manual

Vinten

Vinten HS-105P Instruction Manual

Vinten

Vinten Vision Ped Plus Manual

Vinten

Vinten 3320 User manual

Vinten

Vinten Vector 70 User manual

Vinten

Vinten PRO-5Plus Manual

Vinten

Vinten vector 750 Manual

Vinten

Vinten Vision 5LF User manual

Vinten

Vinten Quattro-OBL Manual

Vinten

Vinten OSPREY lite User manual

Vinten

Vinten flowtech 75 User manual

Vinten

Vinten Vision blue5 User manual

Vinten

Vinten FHR-35 User manual

Vinten

Vinten Vision 100 User manual

Vinten

Vinten Vector 75 V4095-0001 Manual

Vinten

Vinten AutoCam SP-2000/X-Y Instruction Manual

Vinten

Vinten Vector 700H Manual

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Olympus

Olympus PT-EP05L instruction manual

Starlite

Starlite OctoDome nxt instructions