Vinten Pro-Ped Manual

Vinten

Camera Control Solutions

Operators Guide

Pro-Ped

Pedestal

Pro-Ped

Pedestal

Publication Part No. 3983-8 Issue 6

or reproduced in any way including, but not limited to, photocopy, photograph, magnetic or other record without the prior

agreement and permission in writing of

Vinten Broadcast Limited.

Vinten is a registered trademarks of Vinten Broadcast Limited.

Safety - read this first

Warning Symbols in this Operators Guide

Where there is a risk of personal injury, injury to others, or damage to the ped-

estal or associated equipment, comments appear, highlighted by the word

WARNING! and supported by the warning triangle symbol.

Warning symbols on the pedestal

On encountering the warning triangle and open book symbols it is imperative

that you consult this operators guide before using this pedestal or attempting

any adjustment or repair.

Critical data

Mass

Column 19 kg (41.8 lb)

Trim weights (6 off) total 3.4 kg (7.5 lb)

Skid 9.4 kg (20.7 lb)

Load

Maximum load 55 kg (120 lb)

Pressure

Maximum pressure 9.65 bar (140 psi)

≤9.65 bar

<55 kg

9.4

Technical data

Studio OB

Payload 55 kg (120 lb) 55 kg (120 lb)

Column weight 19 kg (41.8 lb) 19 kg (41.8 lb)

Skid weight 9.4 kg (20.7 lb) 9 kg (19.8 lb)

Trim weights (6 off - total) 3.4 kg (7.5 lb) 3.4 kg (7.5 lb)

Total pedestal weight 31.8 kg (70 lb) 31.4 kg (69.1 lb)

Minimum height 66.6 cm (26.2 in.) 68.5 cm (27 in.)

Maximum height 147.5 cm (58.1 in.) 150 cm (59.1 in.)

On-shot stroke 41 cm (16.1 in.) 41 cm (16.1 in.)

Skid leg radius 48 cm (19 in.) 48 cm (19 in.)

Doorway tracking width 97 cm (38 in.) 97 cm (38 in.)

Transit doorway width 86 cm (34 in.) 86 cm (34 in.)

Narrow doorway width 70 cm (27.5 in.) 70 cm (27.5 in.)

Wheel diameter 12.5 cm (5 in.) 15 cm (6 in.)

Steering ring diameter 53.4 cm (21 in.) 53.4 cm (21 in.)

Max working pressure 9.65 bar (140 psi) 9.65 bar (140 psi)

Relief valve pressure 11.38 bar (165 psi) 11.38 bar (165 psi)

Usage

The Pro-Ped Pedestal is designed for use in television studios and on location to support and bal-

ance a pan and tilt head, camera and ancillary equipment weighing up to 55 kg (120 lb).

The Pro-Ped Pedestal is intended for use by television camera operators.

Further information

For further information or advice regarding this pedestal, please contact Vinten Broadcast Limited,

your local Vinten distributor or visit our website.

For full details on maintenance and spare parts, please refer to the Pro-Ped pedestal Maintenance

Manual and Illustrated Parts List - Publication Part No. 3983-9, obtainable from Vinten Broadcast

Limited or your local Vinten distributor. For information on-line, visit our website at

www.vinten.com.

WARNING! If you do not understand how to operate this pedestal, do not

attempt to use it.

Maintenance beyond that detailed in this Operators Guide must

be performed only by competent personnel in accordance with

the procedures laid down in the Maintenance Manual.

Contents

Page

Safety - read this first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Critical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Further information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Operation

Assembling the pedestal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Pressurizing the pedestal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

.Fitting and balancing the load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Using the Pro-Ped pedestal

Height adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Brakes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Cable guards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Pedestal movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Transportation and storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Servicing

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Routine checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Adjustments

Skid clamp adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Elimination of radial and side play on the top stage.. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Associated Publications

Pro-Ped Pedestal

Maintenance Manual

Part No. 3983-9

Pro-Ped Pedestal (Studio Version)

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(22)

(20)

(19)

(18)

(17)

(13)

(16)

(21)

(15) (14) (13) (12) (11)

(23)

Pro-Ped Pedestal (Studio Version)

(1) Four-bolt mounting plate

(2) Control valve

(3) Pressure gauge

(4) Top stage

(5) Drag control

(6) Bottom stage

(7) Safety catch

(8) Trim weight

(9) Long strut

(10) Velcro strap

(11) Cable guard

(12) Track lock pin

(13) Short strut

(14) Skid clamp

(15) Wheel brake

(16) Foot support and strap

(17) Trim weight stowage

(18) Outer tube

(19) Bottom clamp

(20) Top clamp

(21) Steering ring

(22) Weight tray

(23) Schrader valve and cap

Introduction

The Pro-Ped pedestal comprises a central two-stage telescopic column and a skid assembly with

castoring wheels. For transport and storage, the column and skid may be separated and the skid

folded.

The top stage (4) may be pressurized manually, using the self-contained pump, or from an exter-

nal pressure source. Balance is achieved with approximately 1.5 bar pressure for every 10 kg of

load (10 psi for every 10 lb). Trim weights (8) are provided for fine balance.

The skid comprises a centre casting with carrying handle, a fixed leg and two folding legs. Each

leg carries a braked castoring wheel (15) and a foot support with strap (16) to secure the column

leg. Two versions of the skid are available. The OB skid has 150 mm (6 in.) wheels. The studio

skid has 125 mm (5 in.) wheels with cable guards (11) and track locks (12) which provide castor,

track or steer movement of the pedestal.

Operation

Assembling the pedestal

Turn the skid upside-down, depress the leg locking plungers and swing each folding leg out until

the plungers lock the legs in the open position.

Set the skid on the ground on its wheels and apply the brakes (15).

Install the column on the skid as follows:

Ensure that the rubber straps on each foot support (16) are to the outside of the ball joint.

Hold the column upright and release the Velcro retaining strap (10) holding the three struts.

Raise the longer strut (9) to about 30°from the horizontal. The strut joint is adjusted to retain

the strut in this position.

Lift the column, holding the two shorter struts (13) out from the column. Align the long strut

with the fixed leg of the skid and carefully lower the column base into the skid centre, at the

same time engaging the struts with the ball joints on each foot support.

Secure the struts to the supports with the rubber straps (16).

Tighten the skid clamp (14), using moderate hand pressure only. The clamp lever has a

spring loaded ratchet-type action and is operated as follows:

Turn the clamp lever clockwise as far as possible.

Pull the lever outward against the spring pressure, return it to vertical and release.

Turn lever clockwise again.

Repeat until the skid clamp is sufficiently tightened.

Secure the Velcro retaining strap (10) clear of the skid wheels.

If the pedestal is already pressurized, the load may now be fitted. Otherwise pressurize the ped-

estal before fitting the load.

Pressurizing the pedestal

The Pro-Ped may be pressurized manually, by using the self-contained pump, or from an external

source.

A correctly pressurized pedestal will balance its payload such that it can be moved to any position

over the full on-shot stroke of the top stage, with minimum effort, and it will maintain its position

when the steering ring is released. Balance is achieved with approximately 1.5 bar pressure for

every 10 kg of load (10 psi for every 10 lb).

WARNING! This pedestal must be pressurized only with clean, dry air or

nitrogen. A pressure reducing valve must be fitted to the pres-

sure line between the gas cylinder and the outlet connection of

the hose. The reducing valve must be screwed into the gas cyl-

inder outlet. The maximum pressure on the outlet side of the

reducing valve must not exceed 9.65 bar (140 psi). Do not pres-

surize the pedestal beyond the maximum safe working pressure

indicated by the leading edge of the red sector on the gauge.

The pedestal is fitted with a pressure relief valve as a safeguard

against over-pressurization.

Do not attempt to adjust the pressure relief valve

WARNING! A pressurized pedestal will rise rapidly when safety catch is

released. Do not lean over the pedestal when releasing the

safety catch. Always restrain the pedestal by hand pressure on

the steering ring when the safety catch is released.

Control Valve

(2)

PUMP INTERMEDIATE WORK

Table of contents

Other Vinten Camera Accessories manuals

Vinten

Vinten Vector 700 User manual

Vinten

Vinten Vector 750i User manual

Vinten

Vinten Protouch Pro-6HDV System User manual

Vinten

Vinten Vector 90 Manual

Vinten

Vinten Vision blue5 User manual

Vinten

Vinten Vision Ped Plus User manual

Vinten

Vinten Vision Blue Manual

Vinten

Vinten HS-105P Instruction Manual

Vinten

Vinten Vision Blue User manual

Vinten

Vinten RADAMEC Fusion FH-100 Manual

Vinten

Vinten Vision 100 Manual

Vinten

Vinten Vision 250 Manual

Vinten

Vinten Vision 250E User manual

Vinten

Vinten V4109-0001 User manual

Vinten

Vinten pro-touch Pro-10 System User manual

Vinten

Vinten Vision 250E Manual

Vinten

Vinten Vision 3 Manual

Vinten

Vinten Vision 100 User manual

Vinten

Vinten Vision 30 User manual

Vinten

Vinten AutoCam SP-2000/X-Y Instruction Manual

Vinten

Vinten vector 430 Manual

Vinten

Vinten V4045-4980 Manual

Vinten

Vinten Quattro SL User manual

Vinten

Vinten V3955-0002 Manual

Popular Camera Accessories manuals by other brands

Viltrox

Viltrox EF-NEX Mount instructions

Calumet

Calumet 7100 Series CK7114 operating instructions

Ropox

Ropox 4Single Series User manual and installation instructions

Cambo

Cambo Wide DS Digital Series Main operating instructions

Samsung

Samsung SHG-120 Specification sheet

Ryobi

Ryobi BPL-1820 Owner's operating manual

Aegis

Aegis ABL-36020P user manual

Pentax

Pentax Data Back Fc operating manual

Fantasea

Fantasea EyeGrabber F Series instruction manual

Honeywell

Honeywell HDZ20HD user manual

EGO

EGO BA1400T Operator's manual

Sima

Sima SRW-62 user guide

Shape

Shape A7SSMKIT Assembly manual

Slide Kamera

Slide Kamera HST-2 user manual

Power works

Power works 2902613 Original instructions

SES

SES SE-2047-2 user manual

Olympus

Olympus PT-EP05L instruction manual

Starlite

Starlite OctoDome nxt instructions