Videofield SE650 User manual

www.videofied.com

Product Summary

The Exterior Siren/Strobe Model SE650/SE550/SE750 is a wireless

siren designed for use in RSI VIDEO TECHNOLOGIES™ security sys-

tems. The siren includes the following features:

> Totally wireless, battery operated

> Weather-resistant enclosure

> Dual tamper function provides detection for both wall

and cover tamper.

> Transmits check-in/status signal every 8 minutes

Installation Guidelines

For easier installation, programming and RF testing

should be done to check for good communication between

the control panel and all system devices before mounting

system devices. Install the siren and other system devices

in the following order:

>Programming/RF Testing—program siren and

all other devices into the control panel and test

RF communication from each intended device

location to the control panel.

>Mounting—mount siren at the tested location.

Programming/RF Testing

The following provides summarized steps for device

programming and testing. For complete details, refer

to the control panel installation manual.

1Remove four cover

screws, separate cover

from siren and install

batteries.

2Put control panel

into programming/

conguration mode.

3Using a programmed

alphanumeric keypad,

proceed through menus

until the display shows

ADD A NEW DEVICE.

4Press Yes. The display

shows PRESS PROGRAM

BUTTON OF DEVICE.

5Press and release

program button on siren

using a paper clip end.

The siren LED ashes.

Wait for keypad display

to show SIREN (1 - 24)

RECORDED.

6Press Yes. The display shows RADIO RANGE TEST?

Press Yes again. The siren LED starts ashing and

keypad display shows TEST IN PROGRESS.

7Take siren to its intended mounting location and

make sure LED ashes continuously, indicating good

communication with control panel.

8Press Yes to end radio range test, then press Esc/No.

9The display shows ADD A NEW DEVICES?

Repeat steps 4 - 8 for remaining sirens.

10 When nished, exit from conguration mode.

Screws

Program Button

I N S T A L L A T I O N I N S T R U C T I O N S

Exterior Siren/Strobe Model SE650/SE550/SE750

Made by RSI VIDEO TECHNOLOGIES 1012-c February 2008

EMEA SALES

2, rue Alexis de Tocqueville

92160 ANTONY

FRANCE

Phone +33 (0)1 55 59 10 25

Fax +33 (0)3 90 20 66 36

S2View®is a registered trademark of RSI VIDEO TECHNOLOGIES™. Specications subject to change without notice.

USA SALES

4455 White Bear Parkway, Suite 700

White Bear Lake, MN 55110

USA

Phone 877-06-5800

Fax 651-762-4693

www.videofied.com

Mounting

> Use proper tools and hardware for mounting the unit.

> Mount outdoors under eves to help prevent direct contact

from elements.

> Mount on front of structure where strobe light is clearly

visible to responding authorities.

Regulatory Information

FCC Part 15

This device complies with FCC Rules Part 15.

Operation is subject to the following two conditions:

1.) This device may not cause harmful interference and,

2.) this device must accept any interference that may be

received, including interference that may cause undesired

operation.

Changes or modications not expressly approved by RSI VIDEO

TECHNOLOGIES, Inc. can void the user’s authority to operate the

equipment.

Specifications

Panel Compatibility VIDEOFIED V6000/VISIO1000/V7000

Operating Frequency 915/868/920 MHz

Radio type Spread Spectrum Bidirectional RF

Power Requirements Four 1.5 V Alkaline batteries

Battery Type D size alkaline

Power Output 105 dB @ 1 meter

Operating Temperature -13° - 158° F (-25° - +70° C)

Maximum Relative Humidity 70%, non-condensing

Dimensions (LxWxD): 9 in. x 6-1/2 in. x 3 in.

(227 mm x 166 mm x 80 mm)

Weight 31 oz./880 g (without batteries)

Approvals UL / FCC (SE650)

CE / EN50131 / EN300220 / INCERT/ IDA / NCP (SE550)

A-Tick (SE750)

1Remove batteries.

2Hold unit up against

mounting surface and

mark the three

mounting holes.

3Drill pilot holes

and install anchors

where needed.

4Place unit on mouning surface so mounting holes

line up with pilot holes/anchors and secure unit with

appropriate screws.

5Install batteries, observing correct polarity.

6Place the ash wire of the cover to the siren.

7Attach front cover.

Mounting Holes

I N S T A L L A T I O N I N S T R U C T I O N SExterior Siren/Strobe Model SE650/SE550/SE750

This manual suits for next models

Other Videofield Security System manuals

Videofield

Videofield XTO-IP User manual

Popular Security System manuals by other brands

Inner Range

Inner Range Concept 2000 user manual

Climax

Climax Mobile Lite R32 Installer's guide

CADDX

CADDX NX-6 user manual

FBII

FBII XL-31 Series installation instructions

Johnson Controls

Johnson Controls PENN Connected PC10 Install and Commissioning Guide

Aeotec

Aeotec Siren Gen5 quick start guide

Blaupunkt

Blaupunkt SA 2700 quick start guide

IDEAL

IDEAL Accenta Engineering information

AJAX

AJAX DoubleButton user manual

Swann

Swann SW-P-MC2 Specifications

Ecolink

Ecolink Siren+Chime user manual

Digital Monitoring Products

Digital Monitoring Products XR150 user guide

EDM

EDM Solution 6+6 Wireless-AE installation manual

Highway Safety Group

Highway Safety Group EA401 user manual

Siren

Siren LED GSM operating manual

Detection Systems

Detection Systems 7090i Installation and programming manual

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 instructions

Siemens

Siemens FDM273 manual