Vicon IX 2000 L User manual

Installation&

eration Manual

IX 2000 L, IX 2000 H

Colour Camera

Vicon Industries Inc. Does not warrant that the functions contained in this equipment will meet your requirments o

that the operation will be entirely error free or perform precisely as discribed in the documentation. This system

has not been designed to be used in life critical situations and must not be used for this purpose.

Product specifications subject to change without notice.

Vicon and ist logo are registered trademarks of Vicon Industries Inc.

VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAGE, NEW YORK 11788

TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116

24- Hour Technical Support: 800-34-VICON (800-348-4266)

UK: 44/(0) 1489-566300 WEB: vicon-cctv.com

-2-

Dear Customer!

By selecting this VICON product you have chosen a professional device which

guarantees highest possible quality and reliability. We like to thank you very much for

your confidence in our products and kindly ask you to read the following instructions

carefully before commissioning the product in order to be able to take full advantage

of all quality features regarding this product line.

Contents Page

General Information

¨Safety Precautions 3

¨Accessories and Additional Devices 3

Mounting the Camera

¨Mounting the Camera to a Wall Mount 4

Commissioning the Camera

¨Tips for Camera Location 5

¨Adjustment of Back Focus 6

¨Calibration of ES/DC- Lenses 6

¨Focusing the Camera Lens 7

¨Circuit points and operation 8

¨Lens mounting and connection 9

Exhibit

¨Troubleshooting 10

¨Technical Specifications 11

¨Cleaning and Care 12

¨Technical Support 12

¨Notes 13

¨Shipping Instructions 14

GENERAL INFORMATION

-3-

General Information

Safety Precautions

*Read these instructions carefully before commissioning the camera in order to

avoid damages caused by improper installation or use.

*Installation may only be carried out by authorised personnel according to the local

safety regulations.

*Operate the camera with the designated voltage only.

*Follow the safety instructions attached to the camera.

*Never use the camera for other purposes than designated.

*Repairs and adjustments at the camera may only be carried out by authorised

personnel.

*In case of ourdoor use you have to install the camera in a suitable weather

protection case incl. heating element.

*If any liquid or solid matter should get into the housing, disconnect the camera

from power supply and have it checked by your authorised dealer before re-using

(danger of electronic shock!).

*Do not disassemble the camera. To avoid electric shocks, never remove screws or

covers. There are no user-serviceable parts inside it. All maintenance may only be

carried out by authorised personnel according to the local safety regulations.

Install the camera by a least height of 2.30 m.

Composition:

1. Auto Iris Lens Plug

2. Inbus Schlüssel

3. C-Mount Adapter

4. Bedienungsanleitung

1. Auto Iris Lens Plug

2. Remote Plug

3. L-Wrench

4. C-Mount Adapter

5. Instruction Manual

MOUNTING THE CAMERA

-4-

Mounting the Camera

Mounting the Camera to a Wall Mount

COMMISSIONING THE CAMERA

-5-

Commissioning the Camera

Tips for Camera Location

1.0 To avoid internal overheating:

-never expose the camera to direct sunlight without additional camera housing

-keep sufficient distance to direct heat sources.

2.0 Never install the camera at humid, oily or dusty locations without using an

additional housing. (without additional housing the camera is not suitable for

outdoor use!)

3.0 The camera should be installed out of reach (min. height: 2.30 m)

4.0Do not aim the camera towards indoor lighting, the windows, the sunlight or the

sky (to get good pictures, camera and light should be aimed towards the object)

5.0 Reduce the picture detail to the

essential parts of the picture and place

the camera as close as possible to the

object (a smaller picture detail

guarantees sharper details).

6.0 Do not aim the camera towards a

window but instead towards the room.

7.0 Outdoors the camera should be

placed as high as possible so that the

horizon does not appear in the picture.

8.0 Avoid peak light as background (also

caused by reflections, e.g. window

panes).

wrong right

COMMISSIONING THE CAMERA

-6-

Adjustment of Back Focus

This adjustment should only be carried out, if the lens cannot be focused properly

using the lens focus ring. For such a case proceed as follows:

1 Loosen the Allan head screw with the

attached Allan head key. For large distances,

turn the focus ring of the lens almost (0.5 cm)

to the "endless" limit position. If you need to

focus an object near the camera, turn the

focus ring of the lens to a position 1cm before

the "near" limit position.

2 Use the back focus adjustment screw to adjust the distance between lens and

CCD chip until the picture is in focus. Then fix the Allan head screw using the Allan

head key.

3 Finally, focus the picture using the lens focus ring.

Adjustment of ES / DC Lenses

To adjust a lens with automatic iris (DC driven or video driven) to the camera, please

proceed as follows:

1. Turn the level potentiometer (position: ES lenses at the lens itself, DC lenses: at

the camera) to the max. position H (turn right). The monitor picture then appears

to be too bright.

2. Slowly turn the level potentiometer back until the monitor picture appears to be

perfect and is not too bright anymore. Then turn the potentiometer back to the

right (in direction "H") just a little bit.

3. Check the lens performance by using the camera under different and/or changing

light conditions.

Locking screws

COMMISSIONING THE CAMERA

-7-

Focusing the Camera Lens

After you have selected the correct picture detail you have to adjust the lens focus.

The focus adjustment needs to be done with the iris fully open, since the camera has

the smallest depth of focus in this position. If the focus adjustment was not done with

the iris completely open, the picture would be sharp during the day but slowly getting

out of focus the more the light disappears. To fully open the lens, use a grey filter in

front of the lens, provided you are using a lens with automatic iris. Adjust the focus

while the iris is fully open using the lens focus ring. Make sure the most important

picture details are in optimum focus (use a service monitor). If it is not possible to

bring the picture into focus, please adjust the back focus of the camera as described

above.

If you intend to use I.R. illumination at a later stage, you must use an I.R. pass filter

together with the grey filter during focus adjustment to ensure that only I.R. light will

get through to the camera chip and the focus adjustment is done according to this

spectrum, only. Attention: I.R. light can only be used in combination with mono

cameras, not colour cameras!

CIRCUIT POINTS AND OPERATION

-8-

TW // Hold:

TW: Auto tracking white balance,

adjust automatically

Hold: the momentary colour value will

be stored

BLC :

Backlight on / off

GC:

GC on / off

ES // AI:

ES: autom. electr. Shutter

I: autom. Iris

DC // Video:

Change-over between steered video

and steered DC lenses, if the AI

function is activated

L-Lock // Int:

Change-over between internal

synchronisation and linelock. This

function is not availably with 12 V DC!

V- Phase:

Linelock phase setting

DC Level:

Shutter setting with DC lenses

PL:

Power signal

C24V / DC 12V:

Power connection, the polarity with 12V

DC makes no difference

230V AC:

Mains voltage connecting lead

VIDEO OUT:

Videoexit to the monitor etc.

Circuit points and operation

Rear view

12V DC / 24V AC Model

Rear view

230 V AC Model

CIRCUIT POINTS AND OPERATION

-9-

Lens mounting and connection

connection of AI lenses: connection of DC lenses:

1. +8,5 V 1. control –

2. not connected 2. control +

3. control signal 3. drive +

4. GND 4. GND

TECHNICAL SPECIFICATIONS

-10-

Exhibit

Troubleshooting

Error Cause

No picture - No operating voltage (check red LED)

- Coaxial connection interrupted (check video cable)

The picture is noisy - Insufficient light

- The lens drive of the used lens (DC / AI) is not

properly adjusted to the camera (level too low)

The picture is too bright - The lens drive of the used lens (DC / AI) is not

properly adjusted to the camera (level too high)

- Too much peak light; change camera location or

activate backlight function of the camera

The picture is not sharp - Focus not adjusted properly

- Back focus not adjusted properly

- When used outdoors: heater defective; front pane of

camera housing gets steamy

The picture is distorted - Different GND potentials between camera and

monitor; use opto coupler (e.g. VPT from videotronic)

- Bad connections

Ghost image - Wrong 75 Wtermination

- Shield of video cable interrupted

Synchronisation of cameras

does not work properly

- No or bad linelock connection between camera (12

V/DC version) and power adapter

- Mains plug twisted; turn the mains plug by 180° to

change the linelock phase

Please contact your authorised dealer with an exact failure description if none of the

above remedy measures fixes your problem.

This manual suits for next models

Table of contents

Other Vicon Security Camera manuals

Vicon

Vicon V662-D Operating instructions

Vicon

Vicon V2000D-W28IRM User manual

Vicon

Vicon SurveyorVFT SVFT-UPM-1 User manual

Vicon

Vicon I-ONYX MPD-980DN-O User manual

Vicon

Vicon SVR-C User manual

Vicon

Vicon I-ONYX VND-970IP User manual

Vicon

Vicon Roughneck V894CSH Series User manual

Vicon

Vicon CE102D User manual

Vicon

Vicon VC-3000-DSP User manual

Vicon

Vicon SN683D-WIR User manual

Vicon

Vicon V9360-6 Series User manual

Vicon

Vicon VC5050-DSP User manual

Vicon

Vicon SVFT-C22 User manual

Vicon

Vicon V662-D-2 Operating instructions

Vicon

Vicon IX4000AL User manual

Vicon

Vicon rouchneck V910V5 User manual

Vicon

Vicon surveyor 1000 User manual

Vicon

Vicon V960D-N312 Instruction manual

Vicon

Vicon V662V-2 Series Operating instructions

Vicon

Vicon CE102B User manual

Vicon

Vicon surveyor X971 User manual

Vicon

Vicon Roughneck V894CSHR-VF-C User manual

Vicon

Vicon V672-PTZ User manual

Vicon

Vicon V922B-W551MIR-A1 User manual

Popular Security Camera manuals by other brands

Okina USA

Okina USA SIR36-870VF650LP user manual

Divio

Divio NDR155PA user manual

Canon

Canon VB-C500D Specifications

Easy Access

Easy Access EasyGuard user manual

Vivotek

Vivotek FD9389-EHV-v2 Quick installation guide

TUYA

TUYA COSMO W2 manual

Eusso

Eusso UNC7500-IR Advanced installation guide

urmet domus

urmet domus 1096/204 user manual

VC VC20 series operating manual

Axis

Axis Q1614 installation guide

ieGeek

ieGeek DD201 manual

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Installation and user guide

Grundig

Grundig GCH-K0274P owner's manual

Lorex

Lorex VANTAGE LBC7032 quick start guide

4xem

4xem WPT Specifications

Samsung

Samsung SCV-3082 Specifications

Vitek

Vitek VTC-C544 Specifications

Lumens

Lumens VC-A50PNW installation guide