Vetus MP34 User manual

Table of contents

Other Vetus Boating Equipment manuals

Popular Boating Equipment manuals by other brands

Ideal Windlass

Ideal Windlass CWM Installation, operation & maintenance instructions

Access

Access BIMINI Assembly instructions

Floe

Floe VSD 6000 Assembly instructions

Faun

Faun C40 Trackway user manual

Exalto

Exalto 240BS manual

Hobie

Hobie Mirage 360 manual

Dowco

Dowco V322 CC - 2019 installation instructions

Humphree

Humphree HCS-5 installation manual

Dock Doctors

Dock Doctors SLIDING BOARDING STEP Assembly instructions

Mastervolt

Mastervolt Mass Combi 12/2000-100 Quick installation

Zattini Group

Zattini Group bamar BOXTRON E14S Use and maintenance instruction manual

SeaView

SeaView PM5-FMD-8 installation instructions

Grammer

Grammer AVENTO MSG 65/511 Repair manual

Furuno

Furuno TZTL12F installation manual

Harken

Harken 944 instruction sheet

ShoreLand'r

ShoreLand'r DUB 2314 install guide

ProFurl

ProFurl C480 Installation and operation manual

SUSPENZ

SUSPENZ SK Airless Cart quick start guide

Installation

instructions

MP34 M4.15

M4.17

A

X4X3

X2

X6X5 STM6911

BB

Engine control panel c/w panel wiring

MPVB2

MP34BS12 MP34BN12

MPKA02

MPKB02 MPKA04 MPKA06

MPKB04 MPKB06

L = 2 m L = 4 m L = 6 m

MPKA12

MPKB12

L = 12 m

'34'

AB

MP34BS125

B

X2

C

X3

Temp. switch and

oil pressure switch

Sending units to be installed

M2.C5

M2.D5

M2.06

M3.09

M4.15

M4.17

VH4.65

VH4.80

Standard Linea Nost.

VH4.80

Standard

M2.C5

M2.D5

M2.06

M3.09

M4.15

M4.17

VH4.65

Intermediate loom

Interface

Interface cable

STM8326

CT40083

Temperature sending unit Oil pressure sending unit

When using a panel model ‘34’ both warning lights and meters, for coolant temperature and oil pressure have to

be operated.

Installation of both switches for warning lights and sending units for meters into the engine block is not possible.

Therefor some minor modifications have to be carried out:

- At the panel the factory installed connection cables (X2->B and X3->C) have to be replaced by an interface

[STM 6911] and an interface cable [MPVB2].

- At the engine the factory installed switches have to be replaced by sending units, adaptors and washers are

required.

STM6964

Replacing switches for sending units

- On engine, loosen wire nr. B5 (blue)

from the thermo switch.

Replace factory installed thermo

switch by: Temperature sending unit,

adaptor and copper washers.

Reconnect wire B5 to temperature

sensor.

- Loosen wire nr. B2 (brown) from the

oil pressure switch.

Replace factory installed oil pressure

switch by: Oil pressure sending unit,

adaptor, adaptorblock, bolt and wash-

ers. Reconnect wire B2 to oil pressure

sensor.

STM6964 02-03 Printed in the Netherlands

X2 - B

X3 - C

MPVB2MPVB2

STM6911

X2 - B

X3 - C

On panel, remove connection cables, X2 ⇔B and

X3 ⇔C, from warning light printed circuit board (pcb). Install interface pcb [STM6911] onto warning light pcb.

Connect Interface cable [MPVB2] to warning light pcb

and to interface pcb.

Installation of interface and interface cable on ‘34’ model panel

CT40083

STM8326 STM1062

AD14-16

STM6269

M4.15

M4.17

STM7580

STM2018

STM6341

STM2018

STM7582

STM7581

FOKKERSTRAAT 571 - 3125 BD SCHIEDAM - HOLLAND

TEL.: +31 10 4377700 - FAX: +31 (10) 4621286 - 4373474

4153249 - 4372673 - E-MAIL: [email protected]