Vello CB-300 User manual

ONE-YEAR LIMITED WARRANTY

CB-300

This VELLO product is warranted to the original purchaser to be free from defects in

materials and workmanship under normal consumer use for a period of one (1) year

from the original purchase date or thirty (30) days after replacement, whichever

occurs later. The warranty provider’s responsibility with respect to this limited

warranty shall be limited solely to repair or replacement, at the provider’s discretion,

of any product that fails during normal use of this product in its intended manner and

in its intended environment. Inoperability of the product or part(s) shall be

determined by the warranty provider. If the product has been discontinued, the

warranty provider reserves the right to replace it with a model of equivalent quality

and function.

This warranty does not cover damage or defect caused by misuse, neglect, accident,

alteration, abuse, improper installation or maintenance. EXCEPT AS PROVIDED

HEREIN, THE WARRANTY PROVIDER MAKES NEITHER ANY EXPRESS

WARRANTIES NOR ANY IMPLIED WARRANTIES, INCLUDING BUT NOT

LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS

FOR A PARTICULAR PURPOSE. This warranty provides you with speciﬁc legal

rights, and you may also have additional rights that vary from state to state.

To obtain warranty coverage, contact the Vello Customer Service Department to

obtain a return merchandise authorization (“RMA”) number, and return the defective

product to Vello along with the RMA number and proof of purchase. Shipment of the

defective product is at the purchaser’s own risk and expense.

For more information or to arrange service, visit www.vellogear.com or call

Customer Service at 212-594-2353.

Product warranty provided by the Gradus Group.

www.gradusgroup.com

VELLO is a registered trademark of the Gradus Group.

www.vellogear.com

All other trademarks are the property of their respective owners.

GG3

QUICKSHOT

FLASH BRACKET

MANUAL

2. To move from horizontal

(landscape) to vertical (portrait)

positioning, grasp the ﬂash unit

near the shoe mount and pull the

rotating arm down clockwise.

3. At the same time, turn the camera

to vertical orientation.

1. The Vello Rotating Flash Bracket

allows you to hold your camera

as you normally would, right

hand holding the camera, ready

to press the shutter button.

ROTATING THE FLASH

Thank you for choosing a Vello Rotating Flash Bracket. The Vello CB-300

Rotating Flash Bracket accepts SLR and medium format cameras, allowing

you to position a ﬂash directly above the lens in horizontal or vertical

orientation. The adjustable ﬂash shoe is capable of accommodating almost

any portable ﬂash.

The bracket is all metal yet lightweight. It includes a cork pad to prevent

the camera from slipping on the mount. The height of the upright arm of

the bracket is adjustable. There is also a 1/4"-20 socket for tripod

mounting. Integrated feet allow you to securely set your camera down

mid-session. Please follow the instructions below to get the most out of

your Vello Rotating Flash Bracket.

INTRODUCTION

2. Tighten the red knob until the

ﬂash is secure.

1. Turn the red knob

counterclockwise until the shoe

mount is open wide enough to

accommodate the ﬂash.

3. Connect your ﬂash to your

camera with the appropriate

sync cord for your model of ﬂash

and camera (not included). Sync

cords can be obtained from your

photo equipment dealer.

MOUNTING THE FLASH

The Vello Rotating Flash Bracket features an adjustable cold shoe.

FEATURES DIAGRAM

Locking Knob

Shoe Mount Flash Rotating Arm

Mounting Plate

1/4"-20 Camera

Mounting Socket

Alignment Guide Mark

Upright Arm

Tripod 1/4"-20 Socket

2. To move from horizontal

(landscape) to vertical (portrait)

positioning, grasp the ﬂash unit

near the shoe mount and pull the

rotating arm down clockwise.

3. At the same time, turn the camera

to vertical orientation.

1. The Vello Rotating Flash Bracket

allows you to hold your camera

as you normally would, right

hand holding the camera, ready

to press the shutter button.

ROTATING THE FLASH

Thank you for choosing a Vello Rotating Flash Bracket. The Vello CB-300

Rotating Flash Bracket accepts SLR and medium format cameras, allowing

you to position a ﬂash directly above the lens in horizontal or vertical

orientation. The adjustable ﬂash shoe is capable of accommodating almost

any portable ﬂash.

The bracket is all metal yet lightweight. It includes a cork pad to prevent

the camera from slipping on the mount. The height of the upright arm of

the bracket is adjustable. There is also a 1/4"-20 socket for tripod

mounting. Integrated feet allow you to securely set your camera down

mid-session. Please follow the instructions below to get the most out of

your Vello Rotating Flash Bracket.

INTRODUCTION

2. Before tightening the mounting

knob, make certain that the

camera is ﬂush against the

retaining lip of the plate.

1. Mount the camera to the plate

by screwing the mounting knob

into your camera's tripod socket. 2. Adjust the bracket's position. The

center of the lens should align with

the shaped hole in the bracket.

1. Loosen the two screws on the

side of the upright arm.

3. Retighten the screws. The ﬂash

will now be centered above the

lens when you switch to a

vertical orientation.

The top plate can be removed if necessary to accommodate certain models of

larger cameras. Use a screwdriver to remove the screw holding the plate to

the bracket.

TO MOUNT THE CAMERA ADJUSTING THE UPRIGHT ARM

The upright bracket can be adjusted to properly center the ﬂash unit

and to accommodate larger cameras.

2. Before tightening the mounting

knob, make certain that the

camera is ﬂush against the

retaining lip of the plate.

1. Mount the camera to the plate

by screwing the mounting knob

into your camera's tripod socket. 2. Adjust the bracket's position. The

center of the lens should align with

the shaped hole in the bracket.

1. Loosen the two screws on the

side of the upright arm.

3. Retighten the screws. The ﬂash

will now be centered above the

lens when you switch to a

vertical orientation.

The top plate can be removed if necessary to accommodate certain models of

larger cameras. Use a screwdriver to remove the screw holding the plate to

the bracket.

TO MOUNT THE CAMERA ADJUSTING THE UPRIGHT ARM

The upright bracket can be adjusted to properly center the ﬂash unit

and to accommodate larger cameras.

2. Tighten the red knob until the

ﬂash is secure.

1. Turn the red knob

counterclockwise until the shoe

mount is open wide enough to

accommodate the ﬂash.

3. Connect your ﬂash to your

camera with the appropriate

sync cord for your model of ﬂash

and camera (not included). Sync

cords can be obtained from your

photo equipment dealer.

MOUNTING THE FLASH

The Vello Rotating Flash Bracket features an adjustable cold shoe.

FEATURES DIAGRAM

Locking Knob

Shoe Mount Flash Rotating Arm

Mounting Plate

1/4"-20 Camera

Mounting Socket

Alignment Guide Mark

Upright Arm

Tripod 1/4"-20 Socket

2. To move from horizontal

(landscape) to vertical (portrait)

positioning, grasp the ﬂash unit

near the shoe mount and pull the

rotating arm down clockwise.

3. At the same time, turn the camera

to vertical orientation.

1. The Vello Rotating Flash Bracket

allows you to hold your camera

as you normally would, right

hand holding the camera, ready

to press the shutter button.

ROTATING THE FLASH

Thank you for choosing a Vello Rotating Flash Bracket. The Vello CB-300

Rotating Flash Bracket accepts SLR and medium format cameras, allowing

you to position a ﬂash directly above the lens in horizontal or vertical

orientation. The adjustable ﬂash shoe is capable of accommodating almost

any portable ﬂash.

The bracket is all metal yet lightweight. It includes a cork pad to prevent

the camera from slipping on the mount. The height of the upright arm of

the bracket is adjustable. There is also a 1/4"-20 socket for tripod

mounting. Integrated feet allow you to securely set your camera down

mid-session. Please follow the instructions below to get the most out of

your Vello Rotating Flash Bracket.

INTRODUCTION

2. Tighten the red knob until the

ﬂash is secure.

1. Turn the red knob

counterclockwise until the shoe

mount is open wide enough to

accommodate the ﬂash.

3. Connect your ﬂash to your

camera with the appropriate

sync cord for your model of ﬂash

and camera (not included). Sync

cords can be obtained from your

photo equipment dealer.

MOUNTING THE FLASH

The Vello Rotating Flash Bracket features an adjustable cold shoe.

FEATURES DIAGRAM

Locking Knob

Shoe Mount Flash Rotating Arm

Mounting Plate

1/4"-20 Camera

Mounting Socket

Alignment Guide Mark

Upright Arm

Tripod 1/4"-20 Socket