Varitronics VariQuest Perfecta 2400STP User manual
Perfecta®2400STP
&
Perfecta®3600STP
Assembly Instructions
Unpack Printer Stand
1. Cut the straps and open the box.
Important
To avoid scratches, install a blanket on the oor.
2. Remove the documentation and carton tray
on top of the printer.
3. Remove the stand accessories from the tray:
Included is the multi-sheet tray, this will be required later in the
assembly process.
Assemble the Stand
4. Take one of the legs, and turn it upside down. Insert the
crossbar.
Package Contents
The following items are included in the shipping container:
Notes:
• A4/Letter sheet paper (not included) is needed for
printhead alignment during set-up.
• LAN not included (needed if LAN connection required).
Installation Notes
• To unpack the printer, you need at least 6.5 Feet at the
side. The crate size is:
Perfecta® 2400STP
- Length: 52 inches
- Width: 22.4 inches
- Height: 25 inches
Perfecta® 3600STP
- Length: 62 inches
- Width: 22.4 inches
- Height: 25 inches
• Tools required: Screwdriver (included)
• Two people are required to perform some tasks.
• Time required to assemble the printer is approximately
100 minutes.
Perfecta®STP Series Assembly InstructionsPage 2
1 - Printer
2 - Multi-sheet Tray
3 - Documentation:
- Assembly Instructions
- Quick Start Guide
4 - Hex Screwdriver
5 - Black Screws (x4)
6 - Power Cords (x4)
7 - Ink Cartridges (x4)
8 - Stand Pieces:
- Hex Screwdriver
- Screws (x10)
- Supports
- Crossbar
- Fabric Basket
- Left Leg
- Right Leg
9 - Re-Feed Preventers
1 - Hex Screwdriver
2 - Screws (x10)
2 - Black Special Screws (x4)
3 - Supports
4 - Crossbar
5 - Multi-Sheet Tray
6 - Fabric Basket
7 - Left Leg
8 - Right Leg
9. Unfold the basket, move the fabric toward the center of the
brace, and slot the brace into the top of the stand.
10. Slot the basket onto the 2 bars (1 each side).
11. With the triangles pointing towards the basket (1);
slot the 2 supports into the stand (1 each side).
Push each one down hard into place (2).
5. Fix into place with 2 screws.
6. Take the other leg and turn it upside down.
Insert the crossbar.
Note:
Make sure the two black vertical bars for supporting the
basket are on the same side.
7.Fix into place with 2 screws.
8. Turn the stand upright.
Perfecta®STP Series Assembly Instructions Page 3
12. Insert 2 black special screws and nuts into both sides of
the leg (4 total), and tighten by hand.
Note:
If it is dicult to insert the screws; go back to the previous
step, and check the supports are well in place.
13. Tighten the 4 screws by hand (2 each side).
14. Fully tighten the 4 screws (2 each side) with the
hex screwdriver, holding opposite side in place.
15. Check the 4 wheels are locked.
Remove Printer Packaging
16. Open the printer box.
17. Remove the tapes from the lm, then remove the
tray and box.
18. Remove the tapes from the endcaps, and
remove the packing pieces.
19. Uncover the printer by cutting open and
pulling down the plastic bag.
Perfecta®STP Series Assembly InstructionsPage 4
22. The printer should appear as below.
Install the Re-Feed Preventer
23. Locate the 2 re-feed preventer mounts on the
scanner input platen on the front of the printer.
24. Clip the 2 re-feed preventers into position on the mounts.
Remove Tape and Prepare Machine
25. Remove the orange tapes from the top, front end, and
rear of the printer. Remove all the protective lm from the
front panel and the printer’s surface.
Attach Printer to Stand
Important
Make sure that the stand and printer are in the correct
position for assembly.
20. Place the printer onto the stand, lining up the triangles on
the supports to match up with the ones on
the bottom of the printer.
21. Fix the printer to the stand from underneath.
First insert the 4 black screws, and then tighten them.
Note:
When attaching the printer to the stand, insert the second
screw in to the opposite end of the printer so that the
holes line up easier.
Perfecta®STP Series Assembly Instructions Page 5
30. Close the printhead door.
31. Install the multi-sheet tray, that was previously unpacked,
onto the back of the printer..
32. Open the front window.
33. Rotate a 1/2 turn and remove the pin(s)
from inside the printer.
26. Remove the desicant bag.
27. Open the roll cover and remove the protective lm.
28. Remove the 2 spindle retainers and tape.
29. Open the printhead cover and remove the
protective foam.
Important
Do not touch the printhead or blue latch, no printhead
installation is required at the moment.
Perfecta®STP Series Assembly InstructionsPage 6
38. Select your language and conrm it,
then select your country/region and also conrm it.
39. Select the date and time and conrm it.
40. A message will appear on the front panel asking
you to add the ink cartridges. Open the ink cartridge cover.
41. Insert the 4 ink cartridges clicking them into place.
34. Once all protective foams are removed,
close all the covers that were opened.
35. Connect the power cable to the printer, and the outlet.
36. Connect the printer with an Ethernet cable (not included)
if you plan to conect by LAN. If not you can connect using
WiFi later following the front panel instructions.
37. Once all cables are connected,
check that the printer is ON.
Perfecta®STP Series Assembly Instructions Page 7
42. Once the 4 ink cartridges are installed, close the cover.
43. Follow the front panel alignment instructions.
44. The printer will ask you to load the
paper to align the printhead.
45. Extend the input and output trays.
46. You will be asked to load an A4/Letter sheet into the
multi-sheet tray; load sheet (1); adjust the tray (2);
press OK. Printhead alignment will be initialized.
47. If the printer is connected via LAN; connection will
be automatic. If you prefer to connect via WiFi,
please follow the instructions on the front panel to
select a network, and introduce the details.
Perfecta®STP Series Assembly InstructionsPage 8
Load Paper Roll
48. Remove the blue end cap and load the paper roll onto the
spindle. Be sure paper winds over (in front of) the roll and
replace blue end cap making sure it is snug to the roll.
49. Load spindle with paper roll into the printer.
50. Insert edge of paper into the printer until printer detects it.
Technical Support
For technical assistance, please contact your authorized
VariQuest dealer or the VariQuest Technical Support team:
• Phone: 1-800-328-0585
Perfecta®STP Series Assembly Instructions Page 9
Y2900958 01/21
©2021 Varitronics, LLC. All rights reserved.
Other manuals for VariQuest Perfecta 2400STP
1
This manual suits for next models
1
Table of contents
Other Varitronics Printer manuals
