Uniden 4KTPD-MVF User manual
ProSeries
IP CAMERA
INSTALLATION GUIDE
4KTPD-MVF
4MTPD-MVF
4MTPD-2.8
2MTPD-VF
4MMD-2.8
2MMD-2.8
4MED-3.6
2MED-3.6
© 2018 Uniden America Corporation
Irving, Texas
Issue 1, April 2018
2MTD-2.8
4KB-MVF
4MB-MVF
2MB-VF
4MB-3.6
2MB-3.6
Uniden surveillance products are not manufactured and/or sold with the intent to be used for illegal
purposes. Uniden expects consumer’s use of these products to be in compliance with all local,
state, and federal law. For further information on video surveillance and audio recording legal
requirements, please consult your local, state and federal ofcials.
Uniden constantly works on improving our products. This includes updating our documentation
with the latest rmware changes. Go to www.uniden.com to nd the latest version of all
documentation.
© 2018 Uniden America Corporation
All rights reserved.
3
CONTENTS
OVERVIEW .............................................. 5
WHAT’S INCLUDED ........................................5
INSTALL CAMERAS ...................................... 5
INSTALLATION TIPS .......................................5
TAMPER-PROOF DOMED CAMERAS ..........................6
INSTALL MINI DOME CAMERA ..............................8
What’s Included...............................................8
Install Camera ................................................8
INSTALL EYEBALL DOME CAMERA .......................... 9
What’s Included...............................................9
Install Camera ................................................9
INSTALL TURRET DOME CAMERA ..........................10
What’s Included..............................................10
Install Camera ...............................................10
INSTALL LARGE BULLET CAMERAS......................... 11
What’s Included..............................................11
Install Camera ...............................................12
INSTALL SMALL BULLET CAMERAS.........................12
What’s Included..............................................12
Install Camera ...............................................13
CONNECTING THROUGH PC .............................. 13
USING DEVICEMANAGER TOOL ............................13
WEB ACCESS ............................................14
Set Security Levels ...........................................15
UNIDEN PROSERIES MOBILEPHONE CLIENT................ 16
SOFTWARE OPERATING ..................................16
Add device...............................................17
SPECIFICATIONS ....................................... 18
TAMPER-PROOF DOME CAMERAS .......................... 18
MINI AND EYEBALL DOME CAMERAS........................ 19
4
TURRET DOME AND LARGE BULLET CAMERAS............... 20
SMALL BULLET CAMERAS .................................21
COMPLIANCE .......................................... 22
FCC PART 15.............................................22
IC ......................................................23
THREE-YEAR LIMITED WARRANTY ........................ 23
5
INSTALLATION
OVERVIEW
Uniden’s IP cameras can be installed in either Uniden’s NVR or XVR surveillance systems.
TAMPER-
PROOF DOME
MINI DOME EYEBALL
DOME
TURRET
DOME
LARGE
BULLET
SMALL
BULLET
4KTPD-MVF 4MMD-2.8 4MED-3.6 2MTD-2.8 4KB-MVF 4MB-3.6
4MTPD-MVF 2MMD-2.8 2MED-3.6 4MB-MVF 2MB-3.6
4MTPD-2.8 2MB-VF
2MTPD-VF
WHAT’S INCLUDED
• IP camera
• Mounting template sticker
• Star-tipped Allen wrench
• 2-wire to 2.1mm barrell plug for optional 12V DC power input
• Installation screws and anchors
Network cable and power source are not included. SD cards are not included. If you
plan on using the Automatic Network Restoration feature in the NVR, you will need to
purchase an SD card.
INSTALL CAMERAS
INSTALLATION TIPS
• When selecting an outside location for your cameras, keep in mind that most cameras
are designed to operate between 14°F to 122°F (-10°C to 50°C) with a relative humidity
of up to 95%. Avoid installing cameras in direct sunlight, and consider wind chill and other
environmental factors, too.
• Mount the camera in an area that is visible, but out of reach. Route the wiring so it does not
interfere with power or telephone/cable lines and it should not be where it could be easily cut.
Create a plan for camera wire routing and for camera angle.
• Adjust the camera angle so that it covers an area with high trafc as needed. In “high-
risk” locations, have more than one camera cover the same area. This provides camera
redundancy if a vandal attempts to damage a camera.
• If you position cameras indoors, avoid pointing the camera at a glass window to see outside.
This may result in a bright white ring in the night vision image because the light from the night
vision LEDs may reect off the window glass.
Take the following placement suggestions under consideration:
6
• Cabling Distance From NVR to Camera. The video signal sent from the camera to the DVR
is reduced over distance. The maximum distance allowed is 330 feet (100 meters). A 60 foot
cable is included. If you need a cable longer than 60 feet, then use an RG59 cable (with
suitable connectors).
• Do not submerge any camera.
• Mounting. Ensure the camera is mounted on a stable surface which is capable of supporting 5
times the weight of the camera.
• Avoid direct exposure to the weather. Cameras which are weatherproof may be mounted
outside, such as under an eave or other overhang; however, the image will be affected by rain,
etc., landing on the lens. Do not allow direct sunlight to land on the lens.
1. With the DVR connected to the camera, hold it in the location where you want it mounted.
Check the display on the monitor to verify that the view from that location is acceptable.
2. Mount the camera(s) to the desired surface using the parts in the supplied mounting kit. If
mounting on drywall, use the drywall anchors supplied in the kit.
3. Adjust the camera to ensure that the camera has a satisfactory view of the area you would
like to monitor. Cameras have several adjustment points to provide maximum exibility when
setting the view angle.
TAMPER-PROOF DOMED CAMERAS
1. Remove the camera and accessory items from the box. Verify that all parts are there.
2. Position the installation template sticker on the location (wall, ceiling, etc). Drill a 1” hole as
indicated on the sticker and install anchors and screws.
3. Unscrew the camera from the housing, allowing the camera to
separate from the housing and clear dome.
4. Connect the camera’s network cable tail to the house cabling through the 1” hole.
7
5. If you have a 4K TPD camera, connect the plugs from the
network cable tail to their appropriate cables.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
If installed outdoors, the cable and all cable connections
must be routed inside the wall.
White - Audio Out
Red - Audio In
Yellow - Video (BNC)
Black - Alarm In
Red - Alarm Out
RJ45
Red - 12VDC (optional)
Network
Activity
LEDs
PoE
2.1mm Barrel Adapter
NOTE: 12VDC power supply
not included
6. Align the camera base screw holes to the screws. Hang the
base onto the screws then slide the base along the screw lock
to secure.
Screw Hole
and Lock
7. Remove the protective lms from the inside and outside of the camera dome and clean the
dome with a microber cloth (not included) if available.
Do not use a paper towel to clean the camera lens or dome as it might leave
scratches.
8. Adjust the bracket to swivel the camera up to 175˚ on a
horizontal axis (orients the camera for top/bottom of frame).
Bracket
Swivel
Direction
Swivel
Direction
9. Loosen screw 1 and adjust the camera from 15 - 90˚ on a
vertical axis.
15˚ - 90˚
Screw 1
10.Loosen screw 2 to ne-tune the horizontal axis (+/- 30˚).
As you adjust the camera position, check it through the
NVR Preview screen.
Screw 2
11.Insert an SD card if needed.
SD Card Slot
Reset Button
8
12.Remove the dessicant packet from the sealed plastic envelope
and position it inside the camera.
13.Screw the housing back onto the camera base.
INSTALL MINI DOME CAMERA
What’s Included
• IP camera
• Mounting template sticker
• Star-tipped Allen wrench
• 2-wire to 2.1mm barrell plug for optional 12V DC power input
• Installation screws and anchors
• Dessicant package
Install Camera
1. Remove the camera and accessory items from the box. Verify that all parts are there.
2. Position the installation template sticker on the location (wall, ceiling, etc). Drill a 1” hole as
indicated on the sticker and install anchors and screws.
3. Unscrew the camera from the housing, allowing the camera to
separate from the housing and clear dome.
4. Connect the camera’s network cable tail to the house cabling
through the 1” hole.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
If installed outdoors, the cable and all cable connections
must be routed inside the wall.
RJ45
Red - 12VDC (optional)
PoE
2.1mm Barrel Adapter
NOTE: 12VDC power supply
not included
5. Align the camera base screw holes to the screws. Hang the
base onto the screws then slide the base along the screw lock
to secure.
Screw Hole
and Lock
6. Remove the protective lms from the inside and outside of the camera dome and clean the
dome with a microber cloth (not included) if available.
Do not use a paper towel to clean the camera lens or dome as it might leave
scratches.
9
7. Adjust the collar to swivel the camera up to 175˚ on a horizontal
axis (orients the camera for top/bottom of frame).
As you adjust the camera position, check it through the
NVR Preview screen. Thumb
Control
Adjustable
collar
8. Insert an SD card if needed.
SD Card Slot
Reset Button
9. Remove the dessicant packet from the sealed plastic envelope
and position it inside the camera.
10.Align the tab on the housing with the slot on the camera base
for easier reassembly. Tighten screws.
INSTALL EYEBALL DOME CAMERA
What’s Included
• IP camera
• Mounting template sticker
• Star-tipped Allen wrench
• 2-wire to 2.1mm barrell plug for optional 12V DC power input
• Installation screws and anchors
• Dessicant package
Install Camera
1. Remove the camera and installation items from the box. Verify that all parts are there.
2. Hold the camera and sleeve steady and unscrew the ring from
the base.
Base
Ring
Camera
Sleeve
3. Position the installation template sticker on the location (wall, ceiling, etc). Drill a 1” hole as
indicated on the sticker. Install the anchors.
4. Position the base on the template, aligning the screw holes to the anchors, and screw it into
position.
10
5. Connect the network cable tail to the house cabling through the
1” hole.
When using an optional external power supply, the AC
socket outlet shall be installed near the equipment and be
easily accessible.
If installed outdoors, the cable and all cable connections
must be routed inside the wall.
RJ45
Red - 12VDC (optional)
PoE
2.1mm Barrel Adapter
NOTE: 12VDC power supply
not included
6. Unscrew the hatch on the camera to insert an SD card if
needed.
7. Remove the dessicant packet from the sealed plastic envelope
and position it inside the camera.
8. Reassemble the camera, sleeve, and ring. Position the assembly onto the base and adjust
the camera to the correct viewing angle.
As you adjust the camera position, check it through the NVR Preview screen.
9. When the viewing angle is correct, tighten the ring to the base.
As you tighten the ring, keep adjusting the camera as needed.
INSTALL TURRET DOME CAMERA
What’s Included
• IP camera
• Mounting template sticker
• Star-tipped Allen wrench
• 2-wire to 2.1mm barrell plug for optional 12V DC power input
• Installation screws and anchors
• Dessicant package
Install Camera
1. Remove the camera and installation items from the box. Verify that all parts are there.
This manual suits for next models
13
Table of contents
Other Uniden Security Camera manuals
Uniden
Uniden App Cam Pano Series User manual
Uniden
Uniden UDS655 User manual
Uniden
Uniden App Cam Home+ User manual
Uniden
Uniden LightCam 40HD User manual
Uniden
Uniden App Cam 4K Bullet-S User manual
Uniden
Uniden BW31PTZ User manual
Uniden
Uniden UDS655 User manual
Uniden
Uniden NVR - 8 User manual
Uniden
Uniden AppCam 4OPT User manual
Uniden
Uniden LightCam 40HD User manual
Uniden
Uniden AppCam 50HD User manual
Uniden
Uniden App Cam Solo Pro Series User manual
Uniden
Uniden Guardian GC45 User manual
Uniden
Uniden APPCAM PAN/TILT User manual
Uniden
Uniden UDR444 User manual
Uniden
Uniden Pro710NPTZC User manual
Uniden
Uniden UDRC14 User manual
Uniden
Uniden Guardian G710PTZC User manual
Uniden
Uniden UDR744 User manual
Uniden
Uniden UWS1100 User manual
