Ubiquiti TS-8-PRO User manual
8-Port Power over Ethernet
Managed Switch PRO
Model: TS-8-PRO
1
Introduction
Introduction
Thank you for purchasing the Ubiquiti Networks™TOUGHSwitch™
PoE PRO, which is part of the TOUGHSwitch series:
Name Model Description
TOUGHSwitch PoE TS-5-POE 5-port managed switch
featuring 24V PoE
TOUGHSwitch PoE PRO TS-8-PRO 8-port managed switch
featuring 24V/48V PoE
TOUGHSwitch PoE CARRIER TS-16-CARRIER Two TOUGHSwitch PoE
PROs mounted in a rack
This Quick Start Guide is designed to guide you through the
installation and show you how to access the Configuration
Interface. This Quick Start Guide also includes the warranty terms,
and is for use with the TOUGHSwitch PoE PRO, model TS-8-PRO.
For more information, visit www.ubnt.com/toughswitch
Package Contents
8-Port Power over Ethernet
Managed Switch PRO
Model: TS-8-PRO
TOUGHSwitch PoE PRO Power Cord Quick Start Guide
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s responsibility to
follow local country regulations, including operation within legal frequency channels, output power,
indoor cabling requirements, and Dynamic Frequency Selection (DFS) requirements.
2
TOUGHSwitch™PoE PRO Quick Start Guide
Hardware
Back Panel
Power
Ventilation Holes
Note: There are additional ventilation holes on the top and
sides of the TOUGHSwitch.
Front Panel Ports
Management
USB Reset
1-8
Interface Description
Management
10/100 Mbps port for management. Traffic between
the Management port and numbered ports will
be limited to 10/100 Mbps and, under heavy
load, may cause performance degradation of the
TOUGHSwitch.
USB Reserved for future use.
1-8 10/100/1000 Mbps ports for switching and PoE (also
available for management by default).
Reset
To reset to factory defaults, press and hold the Reset
button for more than 10 seconds while the unit is
already powered on.
3
Hardware
Front Panel LEDs
Power/Link
PoE
Speed/Link/Act
LED State Status
Management
Power/
Link
Off No Power/No Link
Amber
After bootup, the LED indicates
power. After an initial link is
established, the LED indicates a
10/100 Mbps connection. If the
link terminates, the LED turns
off until a link is re-established.
If the unit reboots, the LED will
again indicate power until a link is
established.
1-8
PoE
Off No Power over Ethernet
Green 24V Power over Ethernet
Amber 48V Power over Ethernet
Speed/
Link/Act
Off No link
Amber Link established at 10/100 Mbps
Amber Flashing Link activity at 10/100 Mbps
Green Link established at 1000 Mbps
Green Flashing Link activity at 1000 Mbps
4
TOUGHSwitch™PoE PRO Quick Start Guide
Hardware Installation
Place the TOUGHSwitch on a bench top or other flat surface.
Note: Keep 20 mm of clearance next to the ventilation
holes for adequate airflow.
Installation Requirement
For outdoor applications, shielded Category 5 (or above) cabling
should be used for all wired Ethernet connections and should be
grounded through the AC ground of the power supply.
We recommend that you protect your outdoor networks from
the most brutal environments and devastating ESD attacks with
industrial-grade shielded Ethernet cable from Ubiquiti Networks.
For more details, visit www.ubnt.com/toughcable
Note: Although the cabling can be located outdoors, the
TOUGHSwitch itself should be housed inside a protective
enclosure.
Connecting Power
1. Connect the Power Cord to the Power port of the TOUGHSwitch.
2. Connect the other end of the Power Cord to a power outlet.
5
Installation Requirement
Connecting Ethernet
1. Connect an Ethernet cable from the Ethernet port of your
computer to the Management port of the TOUGHSwitch.
2. Connect Ethernet cables from the Ethernet ports of your
devices to the numbered ports of the TOUGHSwitch.
Note: PoE is disabled by default on all numbered ports
and is not available on the Management port. To enable
PoE on the appropriate ports, use the Ports tab in the
Configuration Interface.
6
TOUGHSwitch™PoE PRO Quick Start Guide
Accessing the Configuration Interface
Connect to the Configuration Interface by performing the
following steps:
1. Ensure that your computer (or other host machine) is
connected to the Management port on the TOUGHSwitch.
Note: By default, you can configure the TOUGHSwitch
via any port; however, we recommend the Management
port. (Access to the Configuration Interface can be
limited to the Management port only. You can configure
this setting on the Device tab.)
2. Configure the Ethernet adapter on your host system with a
static IP address on the 192.168.1.x subnet (e.g., 192.168.1.100).
3. Launch your web browser. Type https://192.168.1.20 in the
address field. Press enter (PC) or return (Mac).
4. The login screen will appear. Enter ubnt in the Username and
Password fields. Click Login.
The Configuration Interface will appear, allowing you to customize
your settings as needed.
7
Accessing the Configuration Interface
Configuring PoE Settings
The PoE settings are set to Off by default.
WARNING: Before activating PoE, ensure that the connected
device supports passive PoE and the supplied voltage.
1. On the Status tab, click the Ports tab.
2. On the Ports tab, select the Ethernet port you want to
configure. Select the appropriate PoE Status setting, and then
click Save Changes.
The PoE LED on the Ethernet port will confirm the PoE setting.
For detailed instructions on configuring other features, please
refer to the TOUGHSwitch PoE User Guide. The User Guide is
available at documentation.ubnt.com/toughswitch
8
TOUGHSwitch™PoE PRO Quick Start Guide
Specifications
TOUGHSwitch PoE PRO
Dimensions 210 x 185 x 41 mm
Weight 1.24 kg
Power Input 110-120VAC / 210-230VAC
Max. Power Consumption 150 W
PoE Out Voltage Range 45-48VDC / 22-24VDC
Max. PoE Wattage Per Data Port 11.5 W (24 V), 23 W (48V)
ESD Rating 24 kV Air / 24 kV Contact
PoE Method Passive
Button Reset
USB Port 2.0 Type A (Reserved for Future Use)
Processor MIPS 24K, 400 MHz
System Memory 64 MB
Code Storage 8 MB
Certications CE, FCC, IC
Operating Temperature -25 to 55° C
Operating Humidity 90% Non-Condensing
PoE Congurable Per Port
Management Port N/A
Data Ports Off/24V/48V
LEDs Per Port
Management Port Power/Link
Data Ports PoE, Speed/Link/Activity
Networking Interfaces
Management Port (1) 10/100 Ethernet Port
Data Ports (8) 10/100/1000 Ethernet Ports
Other manuals for TS-8-PRO
1
Table of contents
Other Ubiquiti Network Router manuals
Ubiquiti
Ubiquiti EdgeRouter PoE ERPoe-5 User manual
Ubiquiti
Ubiquiti Edge Pro ERPro-8 User manual
Ubiquiti
Ubiquiti EdgeRouter X ER-X-SFP User manual
Ubiquiti
Ubiquiti UniFi Security Gateway PRO User manual
Ubiquiti
Ubiquiti EdgeRouter LITE User manual
Ubiquiti
Ubiquiti UniFi US-24-250W User manual
Ubiquiti
Ubiquiti EdgeRouter ER-8 User manual
Ubiquiti
Ubiquiti EdgeRouter PoE ERPoe-5 User manual
Ubiquiti
Ubiquiti EdgeRouter 12 User manual
Ubiquiti
Ubiquiti AFi-ALN User manual
Ubiquiti
Ubiquiti EdgeRouter 6P User manual
Ubiquiti
Ubiquiti EdgePoint EP-R8 User manual
Ubiquiti
Ubiquiti LTU LR User manual
Ubiquiti
Ubiquiti EdgeRouter X ER-X User manual
Ubiquiti
Ubiquiti EdgeRouter 4 User manual
Ubiquiti
Ubiquiti ERLite-3 User manual
Ubiquiti
Ubiquiti EdgeRouter PoE ERPoe-5 User manual
Ubiquiti
Ubiquiti EdgePoint R8 Operator's manual
Ubiquiti
Ubiquiti ERLite-3 User manual
Ubiquiti
Ubiquiti airCube Instruction Manual
