Turbosound IMPACT 35T User manual
Quick Start Guide
IMPACT series
IMPACT Quick Start Guide - Page - 1
Models covered by this Quick Start Guide
IMPACT35, IMPACT 35T, IMPACT55T, IMPACT65T.
Thank you for choosing a TURBOSOUND IMPACT series loudspeaker product for your application. If you would like
further information about this or any other TURBOSOUND product, please contact us. A detailed user manual on this
product is available on our web site at www.turbosound.com
Unpacking the Impact Loudspeakers
After unpacking the loudspeakers please check carefully for damage. If damage is found please notify your supplier at
once. You, the consignee, must instigate any claim. Please retain all packaging in case of future re-shipment.
System Requirements
Low Impedance Systems
When used as part of a low impedance system Impact series loudspeakers require only one amplifier channel for correct
operation, the frequency splitting between the LF driver and the HF driver being accomplished by the internal passive
crossover network built into each enclosure. Select the 16Ωsetting on the voltage tap changer on the bottom of the
cabinet. Amplifiers should be capable of delivering long term broadband power equal to the loudspeaker’s program power
rating at its stated nominal impedance.
Use with Subwoofers
Passive subwoofers such as the TSB-110 can be added to increase low frequency performance without the need for
additional power amplifiers. The subwoofer’s internal crossover filters high frequency signals out of the subwoofer
cabinet to ensure a clean transition. Connect first to the subwoofer and then link out to the satellite speakers.
R
R
LL
POWER AMPLIFIER
IMPACT 3
5
TSB-110
EQ
Distributed Systems
Impact 35T, 55T and 65T loudspeakers can be used on 70 volt or 100 volt distributed
systems. Connect loudspeakers to a suitable distribution amplifier, making sure that the
maximum sum of the loudspeakers’ transformer taps do not exceed the distribution
amplifier’s rated power output. Adjust the voltage tap selector to provide the appropriate
loudness level.
Loudspeaker Connections
Electrical connections to the IMPACT loudspeaker are provided as an integral part of the adjustable wall bracket supplied
with each loudspeaker. Simply follow the instructions in the Mounting and Fixing section following.
7.5
15
15
30
60
30
100V
70V
60
Quick Start Guide
IMPACT series
IMPACT Quick Start Guide - Page - 2
Mounting and Fixing
Installing the Loudspeaker with the Supplied Wall Bracket
•The loudspeaker connections are provided as an integral part of the wall bracket.
•Site the bracket on to the mounting surface, making sure there is sufficient free travel
vertically and horizontally to allow full angle adjustment of the loudspeaker, and feed
the speaker cables through the main bracket assembly from the rear.
•Fix the wall bracket securely to the mounting surface using appropriate fixings. The
correct hole spacing and bracket orientation are shown here.
•Terminate the speaker cable by stripping to length and connecting to the bracket
assembly, ensuring correct polarity. The right terminal is positive (+ve) and the left
terminal is negative (-ve).
•Offer the loudspeaker up to the bracket and lock into place with a downward motion.
This action automatically closes the electrical connections.
•Angle the loudspeaker as required and lock the bracket using the 6mm Allen key
provided.
Installing the Loudspeaker with other Wall Brackets
•When installing IMPACT loudspeakers with CB-10, WB-10 or OmniMount™
brackets you will need to terminate the cables directly at the loudspeaker terminal
as shown.
Spares and Accessories
LS-35 3.5” low frequency driver for IMPACT35/35T
LS-50 5” low frequency driver for IMPACT55T
LS-51 5” low frequency driver for IMPACT65T
TW-52 High frequency tweeter for IMPACT35/35T/55T/65T
WB-5 Adjustable plastic wall bracket
WB-10 Adjustable steel wall bracket
CB-10 Adjustable steel ceiling bracket
Turbosound Ltd, Star Road West Sussex RH13 8RY, United Kingdom
tel: +44(0)1403 711447 fax: +44(0)1403 710155 www.turbosound.com
version 1.1
73mm [2.9"]
97mm
[3.8"]
+ve v
e
This manual suits for next models
4
Table of contents
Other Turbosound Speakers manuals
Turbosound
Turbosound Miln series User manual
Turbosound
Turbosound TCS-61/106 User manual
Turbosound
Turbosound TCS SERIES User manual
Turbosound
Turbosound MILAN MI5 User manual
Turbosound
Turbosound iNSPIRE iP300 User manual
Turbosound
Turbosound TCS52C-T-WH User manual
Turbosound
Turbosound iNSPIRE iP3000 User manual
Turbosound
Turbosound TQ Series User manual
Turbosound
Turbosound CMS 801 Series User manual
Turbosound
Turbosound iNSPIRE iP2000 User manual
Turbosound
Turbosound TCS-1061 Quickstart and rigging User manual
Turbosound
Turbosound NuQ SERIES User manual
Turbosound
Turbosound QFLEX WP Series User manual
Turbosound
Turbosound TFM122M User manual
Turbosound
Turbosound TCS Passive Series User manual
Turbosound
Turbosound Venue Series User manual
Turbosound
Turbosound iX Series User manual
Turbosound
Turbosound TCX-8 User manual
Turbosound
Turbosound QLight TQ-115 User manual
Turbosound
Turbosound Manchester Series User manual
