Tuputech TupuCheck Pro User manual
Pro
TupuCheck
Face Recognition & Thermometric
Access Control Terminal
User Manual
Please read this Manual carefully before use.
TupuCheck Pro
Please read this Manual carefully before use.
CONTENTS
· 1-Preface
· 2-FCC regulations
· 3-Safety Precautions
· 4-Packing List
· 5-Appearance
· 6-Power Supply
· 7-Installation Precautions
· 8-Installation Instructions
· 9-Basic Operation
01
01-03
04
05
05
06
06
07-11
12-26
To ensure safety and prevent any damage, please read
this manual carefully before installation and follow the
instructions herein. Store this manual in a secure place
for future reference.
2AWGCTUPUCHECKPRO This device complies with Part
15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that may
cause undesired operation.
Note: Changes or modifications not expressly approved
by the party responsible for compliance could void the
user's authority to operate the equipment.
1-Preface
2-FCC regulations
01
NOTE:THE MANUFACTURER IS NOT RESPONSIBLE FOR
ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHO-
RIZED MODIFICATIONS TO THIS EQUIPMENT.SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY
TO OPERATE THE EQUIPMENT.
NOTE: This equipment has been tested and found to
02
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the followingmeasures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and
receiver.
-- Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV techni-
cian for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure
limits set forth for an uncontrolled environment. This
device and its antenna must not be co-located or
operating in conjunction with any other antenna or
transmitter. To comply with FCC RF exposure compliance
requirements, this grant is applicable to only Mobile
04
Do not move the device by pulling the power cord or any
cable (ignorance may cause the pull off of interfaces)；
Do not leave the lens pointed at the sun, lasers or other
bright light sources. Intense light may cause the image
sensor to deteriorate and damage.
Do not place the device in extremely hot (refer to the
specification of the device for the detailed operating
temperature), cold, dusty or damp locations, and do not
expose it to high electromagnetic radiation;
Please use correct power adaptor (ignorance may cause
damage to the device);
The product is for indoor use. The device cover for indoor
use shall be kept from water and moisture. If installing
the device outdoors, waterproof measures should be
taken to keep the raindrop from entering;
3-Safety Precautions
2.1
2.2
2.3
2.4
2.5
Configurations. The antennas used for this transmitter
must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located
or operating in conjunction with any other antenna or
transmitter.”
Item Quantity Unit
4-Packing List
Turnstile mounting bracket (optional) 1 set
Access Control Terminal 1 set
Wall mounting bracket (optional) 1 set
124mm
263.5mm
23mm
5-Appearance
4.1 Dimension 4.2 Wiring
05
GND
D1
D0
12V
GND
D1
D0
12V Wiegand 26/RS-485
Relay
USB
RJ45 Ethernet
RS485
DC12V-2A
Make sure the device work under stable power supply
and network.
Prepare for a Type 86 Switch Box；
7-Installation Precautions
7.1 Before installation
Device should be installed 1.5m high, the distance for
face recognition is 0.5m-2m，and the optimal distance
for temperature measurement is 50cm.
For the use as access controller, the device should not
be installed far from the access.
7.2 Position for installation and recognition area:
Please use correct power adaptor, DC12V (regulated), to
operate this device. The powe tolerance of this unit is
DC 12V ± 10% (DC10.8V~13.2V), over maximum DC12V
power input may result in the damage of the device.
6-Power Supply
06
1
1
2
2
M4*25mm screw
8-Installation Instructions
Install the Type 86 Switch Box 1.5m high on the wall;
Fix the wall-mounting bracket to the Type 86 Switch Box
with 2 M4x25mm screw;
Pull the network cable and power-supply cable into the
Type 86 Switch Box (to enable the access control with
device, control line also needs to be included)
8.1 Wall mounting
Installatioin of wall mount bracket
07
3
1
2
Note: To connect the relay
Option A: Terminal with ring, the port labeled “12V” can
be used as NO, and the port labeled “GND” can be used
as COM
Option B: Terminal without ring, the port labeled “GND”
can be used as COM, and the port labeled “D1” can be
used as NO
Ring
Port label
GND
D1
D0
12V
GND
D1
D0
12V
08
Connect the network cable to the RJ45 Ethernet inter-
face, connect the power to the DC power supply, (to
enable access control system, also need to connect
control line for access control to the relay interface), put
all the cables into the Switch Box.
4
Table of contents
