Trust SECURITY PLUS-LINE User manual
SECURITY PLUS-LINE
ALSET-2000
ALSET2000 WIRELESS SECURITY SYSTEM
QUICK INSTALL GUIDE
MULTI LANGUAGE
Item 71116 Version 1.0
Visit www.trust.com
for the latest instructions
1
2 3
On
O
u v w x
Learn button 2 sec
LED indicator
4 5
6 7
DELSET
LED indicator
Backplate
DELSET
SET
2 sec
DEL SET
DEL SET
DEL SET
SET
2 sec
8 9
10 11
Arm
O
On
O
ON button
4 sec
OFF button
Short press
ON button
12
14
OTHER
Tamper switch
13a
13b
16
Arm
O
ON button 4 sec
On
O
1.5 sec
15
Tamper switch
18
17
On
O
1.5 sec
O
On
OFF button 4 sec
85 sec.
19 20
On
O
1
ALSET-2000 WIRELESS SECURITY SYSTEM
1. Package content
The following products are included:
uALKCT-2000 Remote control
vALSIR-2000 Siren
wALMST-2000 Magnetic contact sensor
xALMDT-2000 Infrared motion sensor
NOTE: This is a quick installation guide, visit www.trust.com/71116 for more in depth info of the
individual products like:
- Specifications
- Mounting
- Reset/unpair
- Tamper switch
- LED indications
2. Open the ALSIR and place batteries
Open the siren by unscrewing the two screws beneath the light cap. When the screws are removed
the cap of the siren can be slid open. When the cap of the siren is slid open place 4x Alkaline D type
1.5V battery in the siren (not included). Observe the correct polarity of the batteries.
3. Put the ALSIR in learn mode
Slide open the cap and press and hold the siren learn button for about 2 second to enter learn mode.
The LED of the siren will be blinking (in the light cap). The learn mode lasts 15 seconds.
4. Open the ALMST and place batteries
Push with a sharp object on top of the magnetic sensor and pull o the backplate. Insert two 1,5V AAA
Alkaline batteries in the slot (not included). Observe the correct polarity of the batteries (place plus and
minus on the correct side)
EN
ALSET-2000 WIRELESS SECURITY SYSTEM
2
5. Pair the ALMST to the ALSIR
Put the ALSIR in learn mode (see step 3). After putting the ALSIR in learn mode send a pair-signal by
pressing the SET button with a sharp object next to the battery slot of the magnetic sensor. The LED
indicator of the ALMST will flash 5x to confirm that the pairing has been done successfully.
6. Open the ALMDT and place batteries
Open the battery slot on the back side of the motion sensor by pushing the pull-tab down and
removing the battery cover. Insert two AA 1,5V Alkaline batteries as shown above (not included).
Observe the correct polarity of the batteries place plus and minus on the correct side. Close the
battery slot.
7. Pair the ALMDT to the ALSIR
Put the ALSIR in learn mode (see step 3). After putting the ALSIR in learn mode send a pair-signal by
pressing the SET button with a sharp object on the back of the sensor. The LED indicator of the ALMDT
will flash 5x to confirm that the pairing has been done successfully.
8. Open the ALKCT and place battery
Open the battery slot at the back of the ALKCT by sliding it down. Place the included 3V CR2477 battery
and close the battery slot. For more information on replacing and purchasing new batteries visit trust.
com/71115
9. Pair the ALKCT to the ALSIR
1. Put the ALSIR in learn mode (see step 3). Put the ALKCT in pair-mode by first pressing the ON and
OFF button simultaneously for 4 sec (untill the LED of the ALKCT starts blinking).
2. Give a short press on the ON button to pair with the Siren. The LED indicator of the ALKCT will be
flashing 5x to confirm that the pairing has been done successfully.
EN
3
ALSET-2000 WIRELESS SECURITY SYSTEM
10. Mount ALMST
Place the magnetic sensor on the window or door and make sure that both points on the two parts
are in line with each other. Mark the top and bottom of both parts. After marking the positions remove
the sensor.
11. Fasten the ALMST
Screw or tape both backplates of the magnetic sensor on the window or door according to the made
markings. When securing the backplates make sure both parts are mounted with as little space
between as possible (max. 5mm). Place both parts of the magnetic sensor back on the mounted
backplates.
Note: More detailed mounting instructions of the magnetic sensor are available at trust.com/71113
12. Mount ALMDT
Mount the backplate of the motion sensor on a flat surface and secure it with screws. (Screws are
included).
13a. Fasten the ALMDT
Place the ALMDT on the backplate untill you hear a click. Make sure that the backplate is fitted in the
location of the tamper switch.
Note: More detailed mounting instructions of the motion sensor are available at trust.com/71114
13b. Secure the ALMDT
When the ALMDT is placed on the backplate pull it down untill you hear a click to secure it and lock the
tamper switch.
Note: After arming the Siren it is possible to move in front of the sensor for 1 min. It takes ~1.5 minute
before the sensor will be completely active.
14. Mount ALSIR
To fasten the siren slide the cap o (see step 2) remove the batteries and screw the casing with
screws on a flat surface according to the screwholes. (Screws are included). Keep attention that the
tamper switch is pressed to the surface after mounting the siren.
EN
This manual suits for next models
1
Table of contents
Other Trust Security System manuals
Trust
Trust SECURITY PLUS-LINE ALSIR-2000 User manual
Trust
Trust SECURITY PLUS-LINE ALSIR-2000 User manual
Trust
Trust SECURITY PLUS-LINE ALSET-2000 User manual
Trust
Trust SECURITY PLUS-LINE ALSET-2000 Operating manual
Trust
Trust 140BM LCD WIRELESS OBSERVATION SYSTEM User manual
Trust
Trust 200AF User manual
Trust
Trust 200DS User manual
Trust
Trust 200SA User manual
Trust
Trust SECURITY PLUS-LINE ALSIR-2000 User manual
Popular Security System manuals by other brands
EDM
EDM Solution 6+6 Wireless-AE installation manual
Highway Safety Group
Highway Safety Group EA401 user manual
Siren
Siren LED GSM operating manual
Detection Systems
Detection Systems 7090i Installation and programming manual
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 instructions
Siemens
Siemens FDM273 manual