Tronhelicopters Tron 5.5 User manual
MANUAL V 1.1.1
Pages Content
3 Safety notice
4-5 Features and about
6-7 Tools and electronics
8-9 Motor, esc, connectors,blades
10-11 Screws, nuts, shims and washers
12-15 Head assembly
16-22 Tail assembly
23 Servos preparation
24 Battery tray
25-28 Upper main frame assembly
29 Motor mount and pinion
30 Servo frame and motor support.
31-32 Upper and lower main frame assembly
33-36 Landing gear, servos, electronic assembly and wiring.
37-39 Main drive and head to frame assembly
40 Tail boom to main frame assembly
40-43 Final setup, canopy and pre-ight check
2
Index
3
Operate the helicopter in open areas with no people nearby.
Follow your countries air regulation rules.
You may need to join a local club and become a member before you can y the model.
Do NOT operate the helicopter in the following places and situations (or else you risk
severe accidents)
In places where children gather or people pass through in residential areas and parks,
indoors and in limited space in windy weather or when there is rain, snow, fog or other
precipitation. If you do not observe these instructions you may be held liable for personal
injury or property damage!
Always check the R/C system prior to operating your helicopter.
Keep in mind that other people around you might also be operating a R/C model. Ne-
ver use a frequency which someone else is using at the same time. Radio signals will be
mixed and you will lose control of your model.If the model shows irregular behavior, bring
the model to a halt immediately and disconnect the batteries. Investigate the reason and
x the problem. Do not operate the model again as long as the problem is not solved, as
this may lead to further trouble and unforeseen accidents.In order to prevent accidents
and personal injury, be sure to observe the following:Before ying the helicopter, ensure
that all screws are tightened. A single loose screw may cause a major accident.
Replace all broken or defective parts with new ones, as damaged parts lead to crashes.
Never approach a spinning rotor. Keep at least 5 meters/yards away from a spinning rotor
blades.Do not touch the motor immediately after use. It may be hot enough to cause
burns. Perform all necessary maintenance.
PRIOR TO ADJUSTING AND OPERATING YOUR MODEL, OBSERVE THE FOLLOWING
Operate the helicopter only outdoors and out of people’s reach as the main rotor opera-
tes at high rpm!
Note that a badly assembled or improperly adjusted helicopter is a safety hazard!
In the beginning, novice R/C helicopter pilots should always be assisted by an expe-
rienced pilot.
SAFETY FIRST! ALWAYS.
savety notice
YINTECH/Tronhelicopters.
3. Ke Yuan South Road, Guang Cheng
Qu.Dongguan City.
Dongguan 523009.
China.
Wide battery compartment with quick lock and release system.
Light, yet very sti and robust.
Mini or full-size tail servo option.
Motor mounting features a bearing block supported pinion, reducing overall wear on the power system and
drive train.
Compatible with a wide range of motor sizes. 4020, or 4025 series t with easy. From 1000kv-1350kv for 6s
5mm shaft and 6mm shaft diameter ) 14T/5mm included.
Octa boom design with oval side shapes, no boom supports needed.
Capable of using a wide range of lipos. 6,8,10 or even 12S. (6S-5000mAh to 5500mAh recommended).
Well engineered servo layout in conjunction with the FBL system and ESC.
Easy cable routing with various options to ensure a clean setup. Modern, sporty and functional design.
High visibility canopy for perfect orientation in ight.
Recommended main blade size 550-560mm. Tail blade size 86-93mm.
Sustainably produced.
Features.
4
About Tronhelicopters
Designed, engineered and manufactured by YINTECH and Tronhelicopters Switzerland.
Tronhelicopter’s team was built in 2019. Including professional RC Helicopter Pilot and RC
FPV Drone World Champion from 2017 Dario Neuenschwander, we partnered with YIN-
TECH, to provide high-quality manufacturing thanks to over 18 years experience within
the helicopter industry.
Partnered together, an idea was born to release a helicopter that satised the market
needs. Lightweight, strong, simple assembly, ease of maintenance, high quality, a wide
ight envelope with precision and responsiveness, all while delivering unique and sporty
robotic aesthetics.
After over a year of testing, the Tron 5.5 was found to deliver superior performance while
utilizing 550mm class rotor blades. Any pilots will nd not only a great ight experience
but also plenty of neat features of the model.
Pilots can power the Tron 5.5 with a wide variety of motors and battery setups, ranging
from 4020, and 4025 motors, as well as 6s, 8s, and even 12s power systems.
Low head speed and high head speed provide pilots the exibility they want in a helicop-
ter, to meet the performance they want.
No matter your needs as a pilot, the Tron 5.5 will meet them all.
5
CAUTION:
This radio controlled helicopter is not a toy.
The product is not suitable for children under 14 years of age.
SAFETY PRECAUTIONS:
This kit includes some preassembled components. Please check for any
loose screws and tighten them before you proceed with assembly. Use loctite where re-
quired as shown in this manual!
You are responsible for assembly, safe operation, maintenance, inspection and adjust-
ment of the model.
Before beginning assembly, please read these instructions thoroughly.
Check all parts. If you nd any defective or missing parts, contact your local dealer.
For the USA market, The Academy of Model Aeronautics (AMA) is
a national organization representing modelers in the United States.
Please refer to the National Model Aircraft safety code from Academy of
Model Aeronautics.
Tools required
6
2 component epoxy
Loctite 243 / medium strength
Grease
2*Wrench for tail shaft nut
Hex screwdriver
1.5mm/2mm/2.5mm/4mm/5mm
TR501-518 Pair of customized nut wrench for
tail shaft assembly. Optionally available at your
Dealer.
7
Electronics required
3*midi size servos for swashplate
1* midi or full size servo for tail
BL motor. 4020-4025 size/5mm or 6mm
shaft diameter with min. 22mm length
ESC 6S-12S 100A-155A
FBL device and receiver with 6 channel
transmitter.
• KOLIBRI-140-LV.
• PYRO 650-103-1030kv 5 or 6mm shaft.
• PYRO 650L-103-1030kv 5 or 6mm shaft.
Recommendation for Tron 5.5 if you use KONTRONIK equipment.
• TRIBUNUS II 06-120A SBEC ESC.
• TRIBUNUS 12-130A ESC SBEC ESC.
• SCORPION HK-IV-1100 kv 5 or 6mm shaft.
• SCORPION HK-IV 1060 kv 5 or 6mm shaft.
• SCORPION HK-IV 1320 kv 5 or 6mm shaft.
Recommendation for Tron 5.5 if you use SCORPION equipment.
• YGE 135 LVT. ESC.
• YGE AUREUS 135 HVT.ESC.
• HOBBYWING PLATINUM PRO 120A V4.
• HOBBYWING PLATINUM PRO 130A V4.
• XNOVA 4020-1200 kv LIGHTING OR PER-
FORMANCE series 5 or 6mm shaft.
• XNOVA 4020-1350 kv LIGHTING 5 or 6mm
shaft.
• XNOVA 4025-1120 kv LIGHTING 5 or 6mm
shaft.
Recommendation for Tron 5.5 if you use HW,XNOVA,YGE
equipment.
Motor and ESC.
8
Connectors,main and tail blades recommendation.
Motor and ESC.
Main blade recommendation for Tron 5.5 (545mm-560mm length).
Tail blade recommendation for Tron 5.5 (85mm-95mm length).
9
We do recommend to use quality connectors for a safe and solid running setup.
(ESC and battery)
• Supra X Pro S6
• RCPROPLUS Pro-D6 Supra X
10
Screws and nuts.
Table of contents
