TRENDnet TEW-740APBO User manual
TEW-740APBO
Quick Installation Guide
Table of Content
1 English
1. Before You Start
2. Hardware Configuration
3. Hardware Installation
1
1. Before You Start
Package Contents
ŸTEW-740APBO
ŸCD-ROM (User's Guide)
ŸQuick Installation Guide
ŸProprietary PoE injector
ŸPower adapter (48 V DC, 0.5 A)
ŸMounting Hardware
ŸWaterproof RJ-45 plug (network cable is not included)
ŸGrounding wire
Minimum Requirements
ŸComputer with a network port and web browser
ŸA network switch or router with an available network LAN port
Ÿ2 x RJ-45 network cables (sold separately)
ŸPhillips screwdriver (sold separately)
Note:
1. The TEW-740APBO does not support IEEE 802.3at/af. You must use the proprietary Power
over Ethernet injector that is supplied with the TEW-740APBO.
2. Check package contents for waterproof kit (network cable is not included).
Cable Gland Seal Claw Sealing Nut
2
2. Hardware Installation
Phase 1: Overview
Note: The default IP address of the TEW-740APBO is 192.168.10.100. To configure the
TEW-740APBO, your network adapter must have an IP address within the 192.168.10.x subnet
(e.g. 192.168.10.50). Please refer to the Appendix in the User's Guide for more information.
1. Write the MAC address (MAC1) of the two TEW-740APBOs. The MAC address (MAC1) can be
found on the side of the unit. In this example, we will assume the following:
TEW-740APBO #1 MAC Address: 00:11:22:00:00:11
TEW-740APBO #2 MAC Address: 00:11:22:00:11:22
3
Note:
1. The initial configuration should be completed in a testing environment with two
TEW-740APBO's approximately 15 ft. (5 meters) apart from one another.
2. Configure and connect the devices before mounting.
WDS Setup
Included PoE injector
1. Connect one end of a network cable into TEW-740APBO #1.
2. Connect the opposite end of the network cable to the P+DATA OUT port on the Power over
Ethernet Injector.
3. Connect one end of another network cable to the 10/100 DATA IN port on the Power over
Ethernet Injector.
4. Connect the other end of a network cable to your computer's Ethernet port.
5. Connect the power adapter into the Power over Ethernet Injector. Then connect the power
adapter into a power outlet. (EU models have an on/off switch. Please move the power switch
to the “On” position).
6. Assign a Static IP address to your computer's network adapter in the subnet of 192.168.10.x
(e.g. 192.168.10.50) and a subnet mask of 255.255.255.0.
4
7. Open your web browser, type the IP address of the access point in the address bar, and then
press Enter. The default IP address is 192.168.10.100
8. Power on the outdoor access point.
9. Login to the browser configuration page.
10. Change the administrator password.
11. Assign a valid IP address to the access point within the subnet defined by the router. Avoid
using an IP address within the DHCP pool of your router. In this example, we will assume
the following:
Router IP Address: 192.168.10.1
Subnet Mask: 255.255.255.0
DHCP Pool: 192.168.10.100~192.168.10.149
The TEW-740APBO will be setup with the following IP address assignment:
TEW-740APBO #1
IP Address: 192.168.10.50
IP Netmask (Subnet Mask): 255.255.255.0
IP Gateway (Gateway IP Address): 192.168.10.1
Primary DNS: 192.168.10.1
TEW-740APBO #2
IP Address: 192.168.10.51
IP Netmask (Subnet Mask): 255.255.255.0
Gateway IP Address: 192.168.10.1
Primary DNS: 192.168.10.1
12. Enable WDS mode.
13. Enable WPA2-PSK AES encryption and configure a wireless password for the access point.
14. Enter the MAC address of the other outdoor access point.
15. Repeat the process for the second outdoor access point.
5
18. Enter a new admin password.
19. Confirm the new password.
20. Click Save.
21. Please wait while the access point reboots.
Note: Username and password are case sensitive.
16. Confirm connectivity between the two access points.
17. Enter the default username and password, and then click Log In.
Note: For first time installation, you are required to change the admin password.
User Name: admin
Password: admin
29. Click System → Operating Mode.
30. Select WDS Mode and then click Save & Reboot.
System
LAN
Operating Mode
Save & Reboot
31. Please wait while the access point reboots.
System is restarting,
please wait for 50
seconds
22. Enter your new username and the new password, and then click Log In.
23. Click System → LAN.
24. Select Static IP.
25. Configure the IP address, IP Netmask, and IP Gateway based on the example in Phase 1:
Overview.
26. Select Specify DNS Server IP.
27. Configure the Primary DNS based on the example in Phase 1: Overview.
28. Click Save.
6
7
33. Click Wireless → WDS.
Note: To protect your network from any unauthorized access it is recommended to enable
wireless encryption.
34. Enter the MAC address of the other access point. The below configuration will be based on
the example in Phase 1: Overview.
32. Enter the username and password, and then click Log In.
Wireless
WDS
AES
password
Save
8
36. Click Reboot.
37. Repeat steps 2-27 for TEW-740APBO #2.
1. Leave TEW-740APBO #2 connected to your computer.
2. Connect TEW-740APBO #1 to a LAN port of a router on your network.
3. To verify connectivity, run your computer's command prompt and ping TEW-740APBO #1's
assigned IP address from your computer.
4. A successful ping reply determines that both TEW-740APBOs are configured properly and
connected.
Phase 3: Confirm Connectivity
Reboot
35. Click Reboot.
Reboot
Other manuals for TEW-740APBO
4
Table of contents
Other TRENDnet Wireless Access Point manuals
TRENDnet
TRENDnet TEW-841APBO User manual
TRENDnet
TRENDnet TEW-738APBO User manual
TRENDnet
TRENDnet TPL-310AP User manual
TRENDnet
TRENDnet TEW-AP100plus User manual
TRENDnet
TRENDnet TEW-676APBO User manual
TRENDnet
TRENDnet TEW-412APBO User manual
TRENDnet
TRENDnet TEW-825DAP User manual
TRENDnet
TRENDnet TEW-690AP User manual
TRENDnet
TRENDnet TEW-455APBO - 9dBi High Power Wireless Outdoor PoE Access... User manual
TRENDnet
TRENDnet 14dBi User manual
TRENDnet
TRENDnet TEW-410APBplus User manual
TRENDnet
TRENDnet TEW-450APB - Wireless Super G Access Point User manual
TRENDnet
TRENDnet TEW-815DAP User manual
TRENDnet
TRENDnet TEW-636APB User manual
TRENDnet
TRENDnet TEW -739APBO User manual
TRENDnet
TRENDnet TEW-750DAP User manual
TRENDnet
TRENDnet TEW-413APBO User manual
TRENDnet
TRENDnet TEW-434APB - 54Mbps Wireless G PoE Access... User manual
TRENDnet
TRENDnet TEW-450APB - Wireless Super G Access Point User manual
TRENDnet
TRENDnet TEW-815DAP User manual
