TRENDnet TEW-670AP User manual
TEW-670AP
1.01
Quick Installation Guide
Table of Contents
Version 04.09.2010
English
Troubleshooting
1
6
7
1. Before You Start
2. Hardware Installation 2
3. Configure theAccess Point 3
Wireless Tip
1
1. Before You Start
Package Contents
System Requirements
1
•
•CD-ROM (User’s Guide)
•
TEW-670AP
•Multi-Language Quick Installation Guide
Cat. 5 Ethernet cable (1m / 3.2ft)
•PowerAdapter (12V DC, 2.5A)
?
?Acomputer with a network adapter properly installed
?Anetwork Switch or Router with an available network LAN port
Web Browser: Internet Explorer (6.0 or above)
2. Hardware Installation
2
3. Verify that the following panel lights are on:
Power, WLAN(2.4GHz and 5GHz) and
Ethernet.
Note:
Locate an optimum location for theAccess Point. The best place for theAccess Point is
usually at the center of your wireless network. Please connect the computer configuring
the TEW-670AP on the same switch/router.
1. Connect a RJ-45 cable from the Switch/Router
to the LAN port on theAccess Point.
2. Connect theAC PowerAdapter to the
TEW-670APand then to a power outlet.
3
1. Open your web browser, type
http://192.168.10.100 in theAddress bar, and
then press Enter.
3. Configure theAccess Point
Note:
1. It is recommended that you configure theAccess Point from a wired computer. Before
theAccess Point can be configured, a Static IP address must be assigned to your
computer's network adapter in the subnet of 192.168.10.x. Since theAccess Point's
default IP address is 192.168.10.100, make sure no other network devices are
assigned an IP address of 192.168.10.100. (Refer to Troubleshooting section on how
to configure TCP/IPsettings on your PC.)
2. Disable any anti-virus and firewall programs before configuring the access point.
2. Enter the User Name and
Password, and then click OK. By default:
User Name: admin
Password: admin
3. Click Wizard.
4. Click Next.
4
Note:
1. To protect your network from any unauthorized access it is recommended to enable
wireless encryption.
2. The examples below are for WPA2-PSK security. If you select WPA-PSK or
WPA2-PSK, make sure your wireless adapters support WPAor WPA2. If your
wireless adapters do not support WPAor WPA2, then select WEP.
3. For WiFi Protected Setup (WPS) instructions, please refer to the User's Guide on the
CD-ROM. WPS instructions will vary depending on your wireless adapter. Please
contact the manufacture of your wireless adapter for WPS instructions.
5. Mouse over the security bar to select the
desired security level (lowest for no encryption,
highest for WPA2-PSK).
9. Setup is successful. Click Reboot.
8. Enter the desired SSID and Key. Then click
Next. (By default, the SSID for 5GHz WLAN is
TRENDnet670A).
7. Use your mouse to select the desired security
level (lowest for no encryption, highest for
(WPA2-PSK).
6. Enter the desired SSID and Key. Then click
Next. By default, the SSID for 2.4G WLAN is
TRENDnet670N.
2.4GHz WLANConfiguration
5GHz Configuration WLAN
5
11. Click System -> LAN.
13. Wait 14 seconds while theAccess Point
reboots.
12. Configure the LAN settings to match your
network settings and then click Apply.
Your Installation is completed
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
For detailed information regarding the TEW-670AP’s configuration and advanced settings,
please refer to the Troubleshooting section, User's Guide on the CD-ROM, or TRENDnet's
website at http://www.trendnet.com.
13. Wait 15 seconds while theAccess Point
reboots.
10. Wait 30 seconds while theAccess Point
reboots.
Troubleshooting
6
1. How do I configure TCP/IP settings on my computer?
Windows 7
Windows Vista
Windows XP/2000
1. Go into the Control Panel, click Network and Sharing
Center, click ChangeAdapter Settings, right-click the
LocalArea Connection icon and then click Properties.
1. Go into the Control Panel, click Network and Internet,
click Network and Sharing Center, click Manage
Network Connections, right-click the Local Area
Connection icon and then click Properties.
1. Go into the Control Panel, double-click the Network
Connections icon, right-click the Local Area
Connection icon and then click Properties.
2. Click Internet Protocol Version 4(TCP/IPv4)
and then click Properties. Then click on Use the
following IP address, and make sure you
assign your network adapter an IP address in
the subnet of 192.168.10.x.
2. Click Internet Protocol Version 4(TCP/IPv4)
and then click Properties. Then click on Use the
following IP address, and make sure you
assign your network adapter an IP address in
the subnet of 192.168.10.x.
2. Click Internet Protocol (TCP/IP) and then click
Properties. Then click on Use the following IP
address, and make sure you assign your
network adapter an IP address in the subnet of
192.168.10.x.
7
2. I typed http://192.168.10.100 in my Internet Browser'sAddress Bar, but an error message
says “The page cannot be displayed.” How can I get into the TEW-670AP's web
configuration page?
1. Check your hardware settings again by following the instructions in section 2.
2. Make sure the LAN and WLAN lights are lit.
3. Make sure the TCP/IPsettings are configured properly (see question 1).
4. Since theAccess Point's default IP address is 192.168.10.100, make sure that no other
network devices are assigned an IP address of 192.168.10.100.
5. Reset theAccess Point. Take a pin or paperclip and press the RESET button for 15
seconds, then let go. Then type http://192.168.10.100 into your browser.
3. If my network's IP is different than theAccess Point's range, what should I do?
You should still configure theAccess Point first.After all the settings are applied, go to the
Access Point's configuration page, click System -> LAN, change the IP address of theAccess
Point to match your network's IP and save the settings.
4.After I successfully configured the Access Point to meet my network settings, I can not
connect to my network using wireless computers.
If you have a DHCP server in your network, you need to go intoTCP/IP settings again and
re-select "Obtain an IP address automatically" to allow the PC to regain an IPaddress from
your DHCP server.
5.All the settings are correct, but I can not make a wireless connection to the Access Point.
1. Double check that the WLAN light on theAccess Point is lit.
2. Power cycle the TEW-670AP. Unplug the power to the TEW-670AP. Wait 15 seconds, then
plug the power back in.
3. Contact the manufacturer of your wireless network adapter. Make sure the wireless
network adapter is configured with the proper SSID. The default SSID of theAccess Point
is TRENDnet670N (2.4GHz) and TRENDnet670A(5GHz). If you have enabled encryption
on theAccess Point, make sure to configure the wireless network adapter with the same
encryption key.
If you still encounter problems or have any questions regarding the TEW-670AP, please contact
TRENDnet's Technical Support Department.
8
Wireless Tip
The following are some general wireless tips to help minimize the impact of interference
within an environment.
Assign your network a unique SSID. Do not use anything that would be identifying like
“Smith Family Network”. Choose something that you would easily identify when
searching for available wireless networks.
Do not turn off the SSID broadcast. The SSID broadcast is intended to be on and
turning it off can cause connectivity issues. The preferred method of securing a wireless
network is to choose a strong form of encryption with a strong and varied encryption
key.
Change the channel. Most wireless access points and routers are defaulted to channel
6. If you have a site survey tool that will display the channels you can plan your channel
selection around neighboring access points to minimize interference from them. If your
site survey tool does not display the channel try using channels 1 or 11.
If you are using an 802.11n router or access point you can also make the following
changes. Change the channel bandwidth to 20/40MHz. This will provide the highest
possible performance using an 802.11n device. Also, if using 802.11n you should be
securing the network with WPA2 security.
Please also make sure that the wireless hardware is not placed in any type of shelving
or enclosures.
Avoid stacking hardware on top of each other to prevent overheating issues. Maintain
enough free space around the hardware for good ventilation and airflow. There should
also be plenty of free space around the antennas to allow the wireless signal to
propagate.
Note: after setting up the SSID, encryption type and encryption key/passphrase, please
make a note of them for future reference. You will need this information to connect your
wireless computers to the wireless router/access point.
Note: Due to Wi-Fi certification considerations if you choose WEP, WPAor WPA2-TKIP
encryption this device may operate in legacy wireless mode (802.11b/g). You may not
get 802.11n performance as these forms of encryption are not supported by the 802.11n
specification.
Other manuals for TEW-670AP
2
Table of contents
Other TRENDnet Wireless Access Point manuals
TRENDnet
TRENDnet TEW-610APB User manual
TRENDnet
TRENDnet TEW-310APB User manual
TRENDnet
TRENDnet TEW-740APBO User manual
TRENDnet
TRENDnet TPL-110AP - 125Mbps 802.11g Wireless Powerline Access... User manual
TRENDnet
TRENDnet TEW-638APB User manual
TRENDnet
TRENDnet TEW-AP100 User manual
TRENDnet
TRENDnet TPL-110AP - 125Mbps 802.11g Wireless Powerline Access... User manual
TRENDnet
TRENDnet TEW-413APBO User manual
TRENDnet
TRENDnet TEW-638APB User manual
TRENDnet
TRENDnet TEW-230APB User manual
TRENDnet
TRENDnet TEW-753DAP User manual
TRENDnet
TRENDnet TEW-670APB User manual
TRENDnet
TRENDnet TEW-610APB User manual
TRENDnet
TRENDnet TEW-740APBO User manual
TRENDnet
TRENDnet TPL-110AP - 125Mbps 802.11g Wireless Powerline Access... Instruction Manual
TRENDnet
TRENDnet TEW-410APBplus User manual
TRENDnet
TRENDnet TEW-753DAP User manual
TRENDnet
TRENDnet TEW-650AP User manual
TRENDnet
TRENDnet TEW-653AP User manual
TRENDnet
TRENDnet TEW-430APB - Wireless Access Point User manual
